LG 47LW980G / 47LW980S-ZA / 47LW980T / 47LW980W (CHASSIS:LD12D) Service Manual ▷ View online
- 9 -
(7) 3D Input mode
(6) RGB Input
No.
Resolution
H-freq(kHz)
V-freq.(Hz)
Pixel clock(MHz)
Proposed
3D input proposed mode
1
1920*1080
66.587
59.934
74.25
HDTV 1080P
Side by Side, Top & Bottom
No.
Side by Side
Top & Bottom
Checkerboard
Single Frame Sequential
Frame Packing
2D to 3D
1.
- 10 -
ADJUSTMENT INSTRUCTION
1. Application Range
This specification sheet is applied to all of the LED LCD TV
with LD12D chassis.
with LD12D chassis.
2. Designation
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of
(3) The adjustment must be performed in the circumstance of
25 ºC ± 5 ºC of temperature and 65 % ± 10 % of relative
humidity if there is no specific designation.
humidity if there is no specific designation.
(4) The input voltage of the receiver must keep AC 100-240
V~, 50 / 60Hz.
(5) The receiver must be operated for about 5 minutes prior to
the adjustment when module is in the circumstance of over
15.
15.
In case of keeping module is in the circumstance of 0 °C, it
should be placed in the circumstance of above 15 °C for 2
hours
should be placed in the circumstance of above 15 °C for 2
hours
In case of keeping module is in the circumstance of below -
20 °C, it should be placed in the circumstance of above 15
°C for 3 hours.
20 °C, it should be placed in the circumstance of above 15
°C for 3 hours.
[Caution]
When still image is displayed for a period of 20 minutes or
longer (especially where W/B scale is strong. Digital pattern
13ch and/or Cross hatch pattern 09ch), there can some
afterimage in the black level area.
When still image is displayed for a period of 20 minutes or
longer (especially where W/B scale is strong. Digital pattern
13ch and/or Cross hatch pattern 09ch), there can some
afterimage in the black level area.
3. Automatic Adjustment
3.1. ADC Adjustment
(1) Overview
ADC adjustment is needed to find the optimum black level
and gain in Analog-to-Digital device and to compensate
RGB deviation.
* If Adjust ADC is “OTP”, It doesn’t need ADC adjustment.
and gain in Analog-to-Digital device and to compensate
RGB deviation.
* If Adjust ADC is “OTP”, It doesn’t need ADC adjustment.
(GP3-BCM)
(2) Equipment & Condition
1) Jig (RS-232C protocol)
2) MSPG-925 Series Pattern Generator(MSPG-925FA,
2) MSPG-925 Series Pattern Generator(MSPG-925FA,
pattern - 65)
- Resolution : 480i Comp1
1080P Comp1
1920*1080 RGB
1920*1080 RGB
- Pattern : Horizontal 100% Color Bar Pattern
- Pattern level : 0.7 ± 0.1 Vp-p
- Image
- Pattern level : 0.7 ± 0.1 Vp-p
- Image
(3) Adjustment
1) Adjustment method
- Using RS-232, adjust items in the other shown in
“3.1.(3).3)”
2) Adj. protocol
Ref.) ADC Adj. RS232C Protocol_Ver1.0
3) Adj. order
- aa 00 00 [Enter ADC adj. mode]
- xb 00 04 [Change input source to Component1(480i&1080p)]
- ad 00 10 [Adjust 480i Comp1]
- xb 00 06 [Change input source to RGB(1024*768)]
- ad 00 10 [Adjust 1024*768 RGB]
- ad 00 90 End adj.
- xb 00 04 [Change input source to Component1(480i&1080p)]
- ad 00 10 [Adjust 480i Comp1]
- xb 00 06 [Change input source to RGB(1024*768)]
- ad 00 10 [Adjust 1024*768 RGB]
- ad 00 90 End adj.
3.2. MAC address/ CI+ key, Widevine key D/L
Connect: PCBA Jig-> RS-232C Port== PC-> RS-232C Port
Communication Port connection
Communication Port connection
A
Com 1,2,3,4 and 115200(Baud rate)
Mode check : Online Only
A
Check the test process: DETECT -> MAC -> CI -> Widevine
A
Play : START
A
Result : Ready, Test, OK or NG
A
Printer Out(MAC Address Label)
Protocol
Command
Set ACK
Enter adj. mode
aa 00 00
a 00 OK00x
Source change
xb 00 40
b 00 OK40x (Adjust 480i, 1080p Comp1 )
xb 00 60
b 00 OK60x (Adjust 1920*1080 RGB)
Begin adj.
ad 00 10
Return adj. result
OKx (Case of Success)
NGx (Case of Fail)
Read adj. data
(main)
(main)
ad 00 20
000000000000000000000000007c007b006dx
(sub)
(Sub)
ad 00 21
000000070000000000000000007c00830077x
Confirm adj.
ad 00 99
NG 03 00x (Fail)
NG 03 01x (Fail)
NG 03 02x (Fail)
OK 03 03x (Success)
End adj.
aa 00 90
a 00 OK90x
PCBA
PC(RS-232C)
RS-232C Po rt
- 11 -
3.3. LAN Inspection
(1) Equipment & Condition
A
Each other connection to LAN Port of IP Hub and Jig
(2) LAN inspection solution
A
LAN Port connection with PCB
A
Network setting at MENU Mode of TV
A
setting automatic IP
A
Setting state confirmation
-> If automatic setting is finished, you confirm IP and
MAC Address.
3.4. Widevine Key Inspection
Widevine key Inspection
- Confirm key input Data at the “IN START” MENU Mode.
- Confirm key input Data at the “IN START” MENU Mode.
3.5. LAN PORT INSPECTION(PING TEST)
Connect SET -> LAN port == PC -> LAN Port
(1) Equipment setting
1) Play the LAN Port Test PROGRAM.
2) Input IP set up for an inspection to Test Program.
2) Input IP set up for an inspection to Test Program.
*IP Number : 12.12.2.2
(2) LAN PORT inspection (PING TEST)
1) Play the LAN Port Test Program.
2) Connect each other LAN Port Jack.
3) Play Test (F9) button and confirm OK Message.
4) Remove LAN cable.
2) Connect each other LAN Port Jack.
3) Play Test (F9) button and confirm OK Message.
4) Remove LAN cable.
3.6. Model name & Serial number Download
(1) Model name & Serial number D/L
A
Press “Power on” key of service remote control.
(Baud rate : 115200 bps)
(Baud rate : 115200 bps)
A
Connect RS232 Signal Cable to RS-232 Jack.
A
Write Serial number by use RS-232.
A
Must check the serial number at Instart menu.
(2) Method & notice
A. Serial number D/L is using of scan equipment.
B. Setting of scan equipment operated by Manufacturing
B. Setting of scan equipment operated by Manufacturing
Technology Group.
C. Serial number D/L must be conformed when it is
produced in production line, because serial number D/L
is mandatory by D-book 4.0.
is mandatory by D-book 4.0.
* Manual Download (Model Name and Serial Number)
If the TV set is downloaded by OTA or service man, sometimes
model name or serial number is initialized.(Not always)
There is impossible to download by bar code scan, so It
need Manual download.
a. Press the ‘instart’ key of ADJ remote control.
b. Go to the menu ‘5.Model Number D/L’ like below photo.
c. Input the Factory model name(ex 42LW950-ZA) or Serial
model name or serial number is initialized.(Not always)
There is impossible to download by bar code scan, so It
need Manual download.
a. Press the ‘instart’ key of ADJ remote control.
b. Go to the menu ‘5.Model Number D/L’ like below photo.
c. Input the Factory model name(ex 42LW950-ZA) or Serial
number like photo.
d. Check the model name Instart menu. -> Factory name
displayed. (ex 42LW750S-ZA)
e. Check the Diagnostics. (DTV country only) -> Buyer
model displayed. (ex 42LW750S-ZA)
SET
PC
- 12 -
3.7. CI+ Key checking method
Check whether the key was downloaded or not at ‘In Start’
menu. (Refer to below).
menu. (Refer to below).
=> Check the Download to CI+ key value in LGset.
3.7.1. Check the method of CI+ Key value
(1) Check the method on Instart menu.
(2) Check the method of RS232C Command.
(2) Check the method of RS232C Command.
1) Into the main assembly mode (RS232 : aa 00 00)
2) Check the key download for transmitted command.
(RS232 : ci 00 10)
3) Result value
- Normally status for download : OKx
- Abnormally status for download : NGx
- Abnormally status for download : NGx
3.7.2. Check the method of CI+ Key value (RS232)
1) Into the main assembly mode (RS232 : aa 00 00)
2) Check the method of CI+ key by command
(RS232 : ci 00 20)
3) Result value
i 01 OK 1d1852d21c1ed5dcx
3.8. WIFI MAC ADDRESS CHECK
(1) Using RS232
(2) Check the menu on in-start.
4. Manual Adjustment
4.1. ADC Adjustment
ADC adjustment is not needed because of OTP.(Auto ADC
adjustment)
adjustment)
4.2. EDID(The Extended Display Identification
Data)/DDC(Display Data Channel) download
(1) Overview
It is a VESA regulation. A PC or a MNT will display an
optimal resolution through information sharing without any
necessity of user input. It is a realization of “Plug and Play”.
optimal resolution through information sharing without any
necessity of user input. It is a realization of “Plug and Play”.
(2) Equipment
- Since embedded EDID data is used, EDID download JIG,
HDMI cable and D-sub cable are not need.
- Adjust remote control
(3) Download method
1) Press ADJ key on the Adjustment remote control, then
select “12.EDID D/L”, By pressing Enter key, enter EDID
D/L menu.
D/L menu.
2) Select [Start] button by pressing Enter key, HDMI1/
HDMI2/ HDMI3/ HDMI4/ RGB are Writing and display
OK or NG.
OK or NG.
(4) EDID DATA
A
HDMI
A
RGB
CMD 1
CMD 2
Data 0
A
A
0
0
CMD 1
CMD 2
Data 0
C
I
1
0
CMD 1
CMD 2
Data 0
A
A
0
0
CMD 1
CMD 2
Data 0
C
I
2
0
CI+ key Value
H-freq(kHz)
V-freq.(Hz)
Transmission
[A][I][ ][Set ID][ ][20][Cr]
[O][K][X] or [NG]
0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F
0x00 00
FF
FF
FF
FF
FF
FF
00
1E
6D
ⓐ
ⓑ
0x01 ⓒ
01
03
80
10
09
78
0A
EE
91
A3
54
4C
99
26
0x02 0F
50
54
A1
08
00
71
40
81
C0
81
0
81
80
95
0
0x03 90
40
A9
C0
B3
00
02
3A
80
18
71
38
2D
40
58
2C
0x04 45
00
A0
5A
00
00
00
1E
66
21
50
B0
51
00
1B
30
0x05 40
70
36
00
A0
5A
00
00
00
1E
00
00
00
FD
00
39
0x06 3F
1F
52
10
00
0A
20
20
20
20
20
20
ⓓ
0x07
ⓓ
01
ⓔ1
0x00 02
03
37
F1
4E
10
1F
84
13
05
14
03
02
12
20
21
0x01 22
15
01
26
15
07
50
09
57
07
ⓕ
0x02
ⓕ
0x03
ⓕ
E3
05
03
01
01
1D
80
18
71
1C
16
20
58
0x04 2C
25
00
A0
5A
00
00
00
9E
01
1D
00
80
51
D0
1A
0x05 20
6E
88
55
00
A0
5A
00
00
00
1A
02
3A
80
18
71
0x06 38
2D
40
58
2C
45
00
A0
5A
00
00
00
1E
00
00
00
0x07 00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
ⓔ2
0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F
0x00
0
FF
FF
FF
FF
FF
FF
0
1E
6D
ⓐ
ⓑ
0x01 ⓒ
01
03
68
10
09
78
0A
EE
91
A3
54
4C
99
26
0x02 0F
50
54
A1
08
00
71
40
81
C0
81
00
81
80
95
00
0x03 90
40
A9
C0
B3
00
02
3A
80
18
71
38
2D
40
58
2C
0x04 45
00
A0
5A
00
00
00
1E
66
21
50
B0
51
00
1B
30
0x05 40
70
36
00
A0
5A
00
00
00
1E
00
00
00
FD
00
3A
0x06 3E
1E
53
10
00
0A
20
20
20
20
20
20
ⓓ
0x07
ⓓ
0
ⓔ3
Click on the first or last page to see other 47LW980G / 47LW980S-ZA / 47LW980T / 47LW980W (CHASSIS:LD12D) service manuals if exist.