LG 47LW9800-CA (CHASSIS:LC12D) Service Manual ▷ View online
5. Manual Adjustment
5.1 ADC Adjustment
5.1.1 Overview
ADC adjustment is needed to find the optimum black level and gain in Analog-to-Digital device
and to compensate RGB deviation.
LG Electronics
5.1.2 Equipment & Condition
1) Adjust Remocon
2) 801GF(802B, 802F, 802R) or MSPG925FA Pattern Generator
- Resolution: 480i, 720*480
1) Adjust Remocon
2) 801GF(802B, 802F, 802R) or MSPG925FA Pattern Generator
- Resolution: 480i, 720*480
MSPG-925FA Î Model: 209, Pattern: 65) - 480i
1080p, 1920*1080
(MSPG-925FA Î Model: 225, Pattern: 65) - 1080p
- Pattern : Horizontal 100% Color Bar Pattern
- Pattern level: 0.7±0.1 Vp-p
- Image
- Pattern level: 0.7±0.1 Vp-p
- Image
3) Must use standard cable
5.1.3 Adjust method
5.1.3.1 ADC 480i, 1080p Comp1
1) Check connected condition of Comp1 cable to the equipment
2) Give a 480i, 1080p Mode, Horizontal 100% Color Bar Pattern to Comp1.
(MSPG-925FA Î Model: 209, Pattern: 65) - 480i
(MSPG-925FA Î Model: 225, Pattern: 65) - 1080p
(MSPG-925FA Î Model: 225, Pattern: 65) - 1080p
3) Change input mode as Component1 and picture mode as “Standard”
4) Press the In-start Key on the ADJ remote after at least 1 min of signal reception. Then,
4) Press the In-start Key on the ADJ remote after at least 1 min of signal reception. Then,
select 7. External ADC -> 1. COMP 1080p on the menu. Press enter key. The adjustment will
start automatically.
start automatically.
- 17 -
5) If ADC calibration is successful, “ADC RGB Success” is displayed.
If ADC calibration is failure, “ADC RGB Fail” is displayed.
6) If ADC calibration is failure, after recheck ADC pattern or condition retry calibration
Error message refer to
5.1.3.2 ADC 1920*1080 RGB
1) Check connected condition of Component & RGB cable to the equipment
Error message refer to
5.1.3.2 ADC 1920*1080 RGB
1) Check connected condition of Component & RGB cable to the equipment
2) Give a 1920*1080 Mode, 100% Horizontal Color Bar Pattern to RGB port.
(MSPG-925 Series Î
model:225
, pattern:65 )
3) Change input mode as RGB and picture mode as “Standard”
4) Press the In-start Key on the ADJ remote after at least 1 min of signal reception. Then,
4) Press the In-start Key on the ADJ remote after at least 1 min of signal reception. Then,
select 7. External ADC -> 1. COMP 1080p on the menu. Press enter key. The adjustment will
start automatically.
start automatically.
5) If ADC calibration is successful, “ADC RGB Success” is displayed.
If ADC calibration is failure, “ADC RGB Fail” is displayed.
6) If ADC calibration is failure, after recheck ADC pattern or condition retry calibration
Error message refer to 5)
5.2. EDID (The Extended Display Identification Data)
/ DDC (Display Data Channel) download
----We have decided to delete this part from GP2 model.
5.3 White Balance Adjustment
5.3.1 Overview
▪ W/B adj. Objective & How-it-works
- Objective: To reduce each Panel’s W/B deviation
- How-it-works: When R/G/B gain in the OSD is at 192, it means the panel is at its Full
- How-it-works: When R/G/B gain in the OSD is at 192, it means the panel is at its Full
Dynamic Range. In order to prevent saturation of Full Dynamic range and data,
one of R/G/B is fixed at 192, and the other two is lowered to find the desired
value.
one of R/G/B is fixed at 192, and the other two is lowered to find the desired
value.
-Adj. condition : normal temperature
1) Surrounding Temperature: 25±5℃
2) Warm-up time: About 5 Min
3) Surrounding Humidity: 20% ~ 80%
5.3.2 Equipment
1) Color Analyzer: CA-210 (
LED Module : CH 14
)
2) Adj. Computer(During auto adj., RS-232C protocol is needed)
- 18 -
3) Adjust Remocon
4) Video Signal Generator MSPG-925F 720p/216-Gray(Model:217, Pattern:78)
→ Only when internal pattern is not available
▪
4) Video Signal Generator MSPG-925F 720p/216-Gray(Model:217, Pattern:78)
→ Only when internal pattern is not available
▪
Color Analyzer Matrix should be calibrated using CS-1000
5.3.3 Equipment connection MAP
5.3.4 Adj. Command (Protocol)
<Command Format>
START 6E A 50 A LEN A 03 A CMD A 00 A VAL A CS A STOP
<Command Format>
START 6E A 50 A LEN A 03 A CMD A 00 A VAL A CS A STOP
- LEN: Number of Data Byte to be sent
- CMD: Command
- VAL: FOS Data value
- CS: Checksum of sent data
- A: Acknowledge
Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX]
▪RS-232C Command used during auto-adj.
- VAL: FOS Data value
- CS: Checksum of sent data
- A: Acknowledge
Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX]
▪RS-232C Command used during auto-adj.
RS-232C COMMAND
[CMD ID DATA]
[CMD ID DATA]
Explanation
wb
00
00
Begin White Balance adj.
wb
00
10
Gain adj.(internal white pattern)
wb
00
1f
Gain adj. completed
Color Analyzer
Computer
RS-
232C
Pattern Generator
RS-
232C
Probe
※
※If TV internal pattern is used, not
- 19 -
wb
00
20
Offset adj.(internal white pattern)
wb
00
2f
Offset adj. completed
wb
00
ff
End White Balance adj.
(internal pattern disappears )
(internal pattern disappears )
Ex) wb 00 00 -> Begin white balance auto-adj.
wb 00 10 -> Gain adj.
ja 00 ff -> Adj. data
jb 00 c0
...
...
wb 00 1f -> Gain adj. complete
*(wb 00 20(start), wb 00 2f(endc)) -> Off-set adj.
wb 00 ff ->End white balance auto adj.
▪Adj. Map
Applied Model : LD03R Chassis ALL MODELS
Adj.
item
Command
(lower caseASCII)
(lower caseASCII)
Data Range
(Hex.)
(Hex.)
Default
(Decimal)
(Decimal)
Details
CMD1 CMD2 MIN MAX
R Gain
j
g
00
C0
TBD
G Gain
j
h
00
C0
TBD
B Gain
j
i
00
C0
TBD
R
Cut
TBD
G
Cut
TBD
Cool
B
Cut
TBD
R Gain
j
a
00
C0
TBD
G Gain
j
b
00
C0
TBD
B Gain
j
c
00
C0
TBD
R
Cut
TBD
G
Cut
TBD
Medium
B
Cut
TBD
R Gain
j
d
00
C0
TBD
Warm
G Gain
j
e
00
C0
TBD
- 20 -
- 13 -
Click on the first or last page to see other 47LW9800-CA (CHASSIS:LC12D) service manuals if exist.