DOWNLOAD LG 47LW6500-TA / 47LW6510-TB (CHASSIS:LB12C) Service Manual ↓ Size: 13.31 MB | Pages: 115 in PDF or view online for FREE

- 13 -

- ALELF&EDGE LED module change color coordinate

because of aging time.

- Apply under the color coordinate table, for compensated

aging time.

- EDGE LED - LGD Only

Step 1) Connect set and Dongle of Wireless to Cable of HDMI

& TTA 20Pin 

Step 2) At OSD of SET, check the message like Fig 3.
Step 3) Detach Cable of Wireless Dongle 

Step 1) Turn on TV.
Step 2) Press EYE key of Adjustment remote control.
Step 3) Cover the Eye Q II sensor on the front of the using

your hand and wait for 6 seconds.

Step 4) Confirm that R/G/B value is lower than 10 of the “Raw

Data (Sensor data, Back light)”. If after 6 seconds,
R/G/B value is not lower than 10, replace Eye Q II
sensor.

Step 5) Remove your hand from the Eye Q II sensor and wait

for 6 seconds.

Step 6) Confirm that “ok” pop up. If change is not seen,

replace Eye Q II sensor.

Step 1) Turn on TV.
Step 2) At the Local Dimming mode, module Edge Backlight

moving right to left Back light of IOP module moving.

Step 3) Confirm the Local Dimming mode.
Step 4) Press “exit” key.

- Equipment : RF Remote control for test, IR-KEY-Code

Remote control for test

- You must confirm the battery power of RF-Remote control

before test(recommend that change the battery per every lot) 

- Sequence (test)

1) if you select the ‘start(Mute)’ key on the controller, you

can pairing with the TV SET.

2) You can check the cursor on the TV Screen, when select

the ‘OK’ key on the controller 

3) You must remove the pairing with the TV Set by select

‘OK’ Key + ‘Mute’ key on the controller for 5 seconds.

Aging Time

Cool

Medium

Warm

GP3

(Min.)

X

Y

X

Y

X

Y

269

273

285

293

313

329

1

0-2

279

288

295

308

319

338

2

3-5

278

286

294

306

318

336

3

6-9

277

285

293

305

317

335

4

10-19

276

283

292

303

316

333

5

20-35

274

280

290

300

314

330

6

36-49

272

277

288

297

312

327

7

50-79

271

275

287

295

311

325

8

80-149

270

274

286

294

310

324

9

Over 150

269

273

285

293

309

323

Fig.1 

Fig.3 Connect the Dongle  

Fig.2 

Connect

Local Dimming Demo (Edge LED Model)

Local Dimming Demo (IOP & ALEF Model)

- 14 -

(Pattern Generator MSHG-600, MSPG-6100[Support HDMI1.4])
* HDMI mode NO. 872 , pattern No.83

1) Please input 3D test pattern like below (HDMI mode No.

872 , pattern No.83)

2) When 3D OSD appear automatically , then select OK

button.

3) Don’t wear a 3D Glasses, Check the picture like below .

1) Start 3D pattern inspection.
2) If IR emitter signal is correctly received to IR receiver, the

lamp of IR tester turn on

(1) Overview

- Option selection is only done for models in NON-AU/-ID/-

SG/-MY/-VN/-IL/-ZA/-IR

model

(2) Method

1) Press ADJ key on the Adjustment remote control, then

select Country Group Menu

2) Depending on destination, select Country Group Code

12 or Country Group A-ASIA. 

3) Press ADJ key on the Adjustment remote control, then

select Area Option. 

4) Depending on Area code number, select Default Lang.,

Wi-Fi Frequency, Lang Gr., Teletext Lang Gr., I II Save,
HDEV, MONO, Location.

- Method : Press Adj. key on the Adj. Remote Control, then

select Tool option.

After final inspection, press IN-STOP key of the Adjustment
remote control and check that the unit goes to Stand-by
mode.

(1) Method

- Check that Power Cord is fully inserted to the SET.

(If loose, re-insert)

- Unit fully inserted Power cord, Antenna cable and A/V

arrive to the auto-check process. 

- Connect D-terminal to AV JACK TESTER
- Auto CONTROLLER(GWS103-4) ON
- Perform GND TEST
- If NG, Buzzer will sound to inform the operator.
- If OK, changeover to I/P check automatically.
(Remove CORD, A/V form AV JACK BOX)
- Perform I/P test
- If NG, Buzzer will sound to inform the operator.
- If OK, Good lamp will lit up and the stopper will allow

the pallet to move on to next process.

(2) Checkpoint

• TEST voltage

- GND: 1.5 KV / min at 100 mA
- SIGNAL: 3 KV / min at 100 mA

• TEST time: 1 second
• TEST POINT

- GND TEST = POWER CORD GND & SIGNAL CABLE

METAL GND

& NEUTRAL

• LEAKAGE CURRENT: At 0.5 mArms

<IR Tester Lamp turned off(NG)>

<IR Emitter inspection>

<IR Tester Lamp turned on(OK)>

Module

Tool 1

Tool 2

Tool 3

Tool 4

Tool 5

Tool 6

Remark

LGD

33032

4811

3327

17593

47701

726

STD B/L: 55

- 15 -

Measurement condition:
1. RF input: Mono, 1 KHz sine wave signal, 100 % Modulation
2. CVBS, Component: 1 KHz sine wave signal 0.5 Vrms
3. RGB PC: 1 KHz sine wave signal 0.7 Vrms

1) Put the USB Stick to the USB socket.
2) Automatically detecting update file in USB Stick.

- If your downloaded program version in USB Stick is Low,

it didn’t work. But your downloaded version is High, USB
data is automatically detecting.

3) Show the message “Copying files from memory”.

4) Updating is starting.

5) Updating Completed, The TV will restart automatically.
6) If your TV is turned on, check your updated version and

Tool option. (explain the Tool option, next stage)

* If downloading version is more high than your TV have, TV

can lost all channel data. In this case, you have to channel
recover. if all channel data is cleared, you didn’t have a
DTV/ATV test on production line.

* After downloading, have to adjust TOOL OPTION again.

1) Push "IN-START" key in service remote control.
2) Select "Tool Option 1" and push “OK” key.
3) Push in the number. (Each model has their number.)

No.

Item

Min.

Typ.

Max.

Unit

1. 

Audio practical max

9.0

10.0

12.0

W

EQ Off

Output, L/R

AVL Off

(Distortion=10 %

8.5

8.9

9.8

Vrms

Clear Voice Off

max Output)

2. 

Speaker (8 Ω

10.0

15.0

W

EQ On

Impedance)

AVL On

Clear Voice On

- 16 -

A2

AG1

A5

A10

300

200

LV

1

LV

2

120

510

51

1

810

900

910

800

521

530

540

400

710

700

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by       in the Schematic Diagram and EXPLODED VIEW. 
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. 
Do not modify the original design without permission of manufacturer.