DOWNLOAD LG 47LV5700-CA (CHASSIS:LC12E) Service Manual ↓ Size: 10.89 MB | Pages: 120 in PDF or view online for FREE

- 5 -

Some chassis circuit boards have slotted holes (oblong) through
which the IC leads are inserted and then bent flat against the
circuit foil. When holes are the slotted type, the following technique
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique
as outlined in paragraphs 5 and 6 above.

Removal
1.  Desolder and straighten each IC lead in one operation by gently

prying up on the lead with the soldering iron tip as the solder
melts.

2.  Draw away the melted solder with an anti-static suction-type

solder removal device (or with solder braid) before removing the
IC.

Replacement
1.  Carefully insert the replacement IC in the circuit board.
2.  Carefully bend each IC lead against the circuit foil pad and

solder it.

3.  Clean the soldered areas with a small wire-bristle brush.

(It is not necessary to reapply acrylic coating to the areas).

1.  Remove the defective transistor by clipping its leads as close as

possible to the component body.

2.  Bend into a "U" shape the end of each of three leads remaining

on the circuit board.

3.  Bend into a "U" shape the replacement transistor leads.
4.  Connect the replacement transistor leads to the corresponding

leads extending from the circuit board and crimp the "U" with
long nose pliers to insure metal to metal contact then solder
each connection.

1.  Heat and remove all solder from around the transistor leads.
2. Remove the heat sink mounting screw (if so equipped).
3.  Carefully remove the transistor from the heat sink of the circuit

board.

4.  Insert new transistor in the circuit board.
5. Solder each transistor lead, and clip off excess lead.
6.  Replace heat sink.

1.  Remove defective diode by clipping its leads as close as

possible to diode body.

2.  Bend the two remaining leads perpendicular y to the circuit

board.

3.  Observing diode polarity, wrap each lead of the new diode

around the corresponding lead on the circuit board.

4.  Securely crimp each connection and solder it.
5.

Inspect (on the circuit board copper side) the solder joints of

the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.

1.  Clip each fuse or resistor lead at top of the circuit board hollow

stake.

2.  Securely crimp the leads of replacement component around

notch at stake top.

3.  Solder the connections.

Maintain original spacing between the replaced

component and adjacent components and the circuit board to
prevent excessive component temperatures.

Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
board causing the foil to separate from or "lift-off" the board. The
following guidelines and procedures should be followed whenever
this condition is encountered.

At IC Connections
To repair a defective copper pattern at IC connections use the
following procedure to install a jumper wire on the copper pattern
side of the circuit board. (Use this technique only on IC
connections).

1.  Carefully remove the damaged copper pattern with a sharp

knife. (Remove only as much copper as absolutely necessary).

2.  carefully scratch away the solder resist and acrylic coating (if

used) from the end of the remaining copper pattern.

3.  Bend a small "U" in one end of a small gauge jumper wire and

carefully crimp it around the IC pin. Solder the IC connection.

4.  Route the jumper wire along the path of the out-away copper

pattern and let it overlap the previously scraped end of the good
copper pattern. Solder the overlapped area and clip off any
excess jumper wire.

At Other Connections
Use the following technique to repair the defective copper pattern
at connections other than IC Pins. This technique involves the
installation of a jumper wire on the component side of the circuit
board.

1.  Remove the defective copper pattern with a sharp knife.

Remove at least 1/4 inch of copper, to ensure that a hazardous
condition will not exist if the jumper wire opens.

2.  Trace along the copper pattern from both sides of the pattern

break and locate the nearest component that is directly
connected to the affected copper pattern.

3.  Connect insulated 20-gauge jumper wire from the lead of the

nearest component on one side of the pattern break to the lead
of the nearest component on the other side.
Carefully crimp and solder the connections.

Be sure the insulated jumper wire is dressed so the

it does not touch components or sharp edges.

LGE                                            Display Division                                  LG(51) 

                                                                                                                                                                                                                                               

                                                                                                                                                                                                                                          LG  전자 

 

LGE                                            Display Division                                  LG(51) 

                                                                                                                                                                                                                                               

                                                                                                                                                                                                                                          LG  전자 

1. Application range.     
2. Specification   
3. Test Method   
4. Electrical Specification   
5. Feature and Function 

 

6. Safety and Regulation   
7. Video   
8. Digital Receiver (DTMB) 
9. Digital Receiver (DVB-C) 
10. Chroma & Brightness   
11. Audio   
12. Power   
13. Standard Level For Input Signal(Video, Audio, Y/C, Component, RGB)   
14. Component Video Input (Y, PB, PR)   
15. RGB Input ( PC )   
16. HDMI Input   
17. RGB/HV Control Signal In/Out Spec(D-sub15 pin Cable )   
18. USB Input 
19. WIFI 
20. Screen Size(over scan spec)   
21. The others   
22. Reliability   
23. LED Control   

LGE                                            Display Division                                  LG(51) 

                                                                                                                                                                                                                                               

                                                                                                                                                                                                                                          LG  전자 

24. SET factoring condition   
25. Accessories & Mechanical Spec. 
26. Additional Rules   
27. Energy Efficiency Index