LG 47LV375H (CHASSIS:LD03X) Service Manual ▷ View online
- 7 -
ADJUSTMENT INSTRUCTION
1. Application Range
This specification sheet is applied to all of the LCD TV with
LD03X chassis.
LD03X chassis.
2. Designation
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of
(3) The adjustment must be performed in the circumstance of
25 ºC ± 5 ºC of temperature and 65 % ±10 % of relative
humidity if there is no specific designation.
humidity if there is no specific designation.
(4) The input voltage of the receiver must keep AC 100-240
V~, 50 / 60Hz.
(5) The receiver must be operated for about 5 minutes prior to
the adjustment when module is in the circumstance of over
15.
15.
In case of keeping module is in the circumstance of 0 °C, it
should be placed in the circumstance of above 15 °C for 2
hours
should be placed in the circumstance of above 15 °C for 2
hours
In case of keeping module is in the circumstance of below -
20 °C, it should be placed in the circumstance of above 15
°C for 3 hours.
20 °C, it should be placed in the circumstance of above 15
°C for 3 hours.
[Caution]
When still image is displayed for a period of 20 minutes or
longer (especially where W/B scale is strong. Digital pattern
13ch and/or Cross hatch pattern 09ch), there can some
afterimage in the black level area.
When still image is displayed for a period of 20 minutes or
longer (especially where W/B scale is strong. Digital pattern
13ch and/or Cross hatch pattern 09ch), there can some
afterimage in the black level area.
3. Automatic Adjustment
3.1. ADC Adjustment
(1) Overview
ADC adjustment is needed to find the optimum black level
and gain in Analog-to-Digital device and to compensate
RGB deviation.
and gain in Analog-to-Digital device and to compensate
RGB deviation.
(2) Equipment & Condition
1) Jig (RS-232C protocol)
2) MSPG-925 Series Pattern Generator(MSPG-925FA,
2) MSPG-925 Series Pattern Generator(MSPG-925FA,
pattern - 65)
- Resolution : 480i Comp1
1080p Comp1
1080p RGB
1080p RGB
- Pattern : Horizontal 100% Color Bar Pattern
- Pattern level : 0.7 ± 0.1 Vp-p
- Image
- Pattern level : 0.7 ± 0.1 Vp-p
- Image
(3) Adjustment
1) Adjustment method
- Using RS-232, adjust items in the other shown in
“3.1.(3).3)”
2) Adj. protocol
Ref.) ADC Adj. RS232C Protocol_Ver1.0
3) Adj. order
- aa 00 00 [Enter ADC adj. mode]
- xb 00 40 [Change input source to Component1(No action)]
- ad 00 10 [Adjust 480i Comp1]
- ad 00 10 [Adjust 1080p Comp1]
- xb 00 60 [Change input source to RGB(No action)]
- ad 00 10 [Adjust 1080p RGB]
- ad 00 90 End adj.
- xb 00 40 [Change input source to Component1(No action)]
- ad 00 10 [Adjust 480i Comp1]
- ad 00 10 [Adjust 1080p Comp1]
- xb 00 60 [Change input source to RGB(No action)]
- ad 00 10 [Adjust 1080p RGB]
- ad 00 90 End adj.
3.2. MAC Address
(1) Equipment & Condition
- Play file: Serial.exe
- MAC Address edit
- Input Start / End MAC address
- MAC Address edit
- Input Start / End MAC address
(2) Download method
1) Communication Prot connection
Connect: PCBA Jig-> RS-232C Port== PC-> RS-232C Port
PCBA
PC(RS-232C)
RS-232C Po rt
Protocol
Command
Set ACK
Enter adj. mode
aa 00 00
a 00 OK00x
Source change
xb 00 40
b 00 OK40x (Adjust 480i, 1080p Comp1 )
xb 00 60
b 00 OK60x (Adjust 1920*1080 RGB)
Begin adj.
ad 00 10
Return adj. result
OKx (Case of Success)
NGx (Case of Fail)
Read adj. data
(main)
(main : component1 480i, RGB 1080p)
ad 00 20
000000000000000000000000007c007b006dx
(main)
(main : component1 1080p)
ad 00 30
000000070000000000000000007c00830077x
Confirm adj.
ad 00 99
NG 03 00x (Fail)
NG 03 01x (Fail)
NG 03 02x (Fail)
OK 03 03x (Success)
End adj.
aa 00 90
a 00 OK90x
- 8 -
2) MAC Address Download
- Com 1,2,3,4 and 115200(Baud rate)
- Click “Port connection” button(1).
- Click “Port connection” button(1).
- Click “Load” button(2) for MAC Address write.
- Click “MAC Address write” button(3)
- Check the OK Or NG.
- Click “MAC Address write” button(3)
- Check the OK Or NG.
3.3. LAN
(1) Equipment & Condition
A
Each other connection to LAN Port of IP Hub and Jig
(2) LAN inspection solution
A
LAN Port connection with PCB
A
Network setting at MENU Mode of Installation Menu
- “In-start” key input -> “menu” key input -> Installation
Menu
- Network Setup -> Network Setting --> Press “Enter” ->
IP Auto Setting -> OK
A
setting automatic IP
A
Setting state confirmation
-> If automatic setting is finished, you confirm IP and
MAC Address.
3.4. LAN PORT INSPECTION(PING TEST)
Connect SET -> LAN port == PC -> LAN Port
(1) Equipment setting
1) Play the LAN Port Test PROGRAM.
2) Input IP set up for an inspection to Test Program.
2) Input IP set up for an inspection to Test Program.
*IP Number : 12.12.2.2
(2) LAN PORT inspection (PING TEST)
1) Play the LAN Port Test Program.
2) Connect each other LAN Port Jack.
3) Play Test (F9) button and confirm OK Message.
4) Remove LAN cable.
2) Connect each other LAN Port Jack.
3) Play Test (F9) button and confirm OK Message.
4) Remove LAN cable.
3.5. Model name & serial number download
(1) Model name & Serial number D/L
A
Press “Power on” key of service remote control.
(Baud rate : 115200 bps)
(Baud rate : 115200 bps)
A
Connect RS232 Signal Cable to RS-232 Jack.
A
Write Serial number by use RS-232.
A
Must check the serial number at Instart menu.
(2) Method & notice
A. Serial number D/L is using of scan equipment.
B. Setting of scan equipment operated by Manufacturing
B. Setting of scan equipment operated by Manufacturing
Technology Group.
C.Serial number D/L must be conformed when it is
produced in production line, because serial number D/L
is mandatory by D-book 4.0.
is mandatory by D-book 4.0.
* Manual Download (Model Name and Serial Number)
If the TV set is downloaded by OTA or service man, sometimes
model name or serial number is initialized.(Not always)
There is impossible to download by bar code scan, so It
need Manual download.
a. Press the ‘Instart’ key of Adjustment remote control.
b. Go to the menu ‘5.Model Number D/L’ like below photo.
c. Input the Factory model name(ex 42LD450-ZA) or Serial
model name or serial number is initialized.(Not always)
There is impossible to download by bar code scan, so It
need Manual download.
a. Press the ‘Instart’ key of Adjustment remote control.
b. Go to the menu ‘5.Model Number D/L’ like below photo.
c. Input the Factory model name(ex 42LD450-ZA) or Serial
number like photo.
d. Check the model name Instart menu. -> Factory name
displayed. (ex 42LE7500-ZA)
e. Check the Diagnostics. (DTV country only) -> Buyer
model displayed. (ex 42LE7500-ZA)
Commercial MENU
SET
PC
- 9 -
4. Check Commercial Features
4.1. External SPK Out and Volume control
4.1.1. Equipment & Condition
- Jig(Speaker out JIG, Speaker out control Jig) or Oscilloscope
- Power only mode
- Power only mode
4.1.2. Check the speaker out & control
1) Connect the External Speaker : Check the sound.
2) Press the “+” key on the control Jig : Check the Max output.
3) Press the “-” key on the control Jig : Check the Min output.
2) Press the “+” key on the control Jig : Check the Max output.
3) Press the “-” key on the control Jig : Check the Min output.
Connect oscilloscope, you can see this waveform.
4.2. IR Out and DC Power Outlet(5 V / 12 V)
4.2.1. Equipment & Condition
- Jig (commercial check JIG)
- Special 232C Cable for commercial check Jig
- Power only mode
- Special 232C Cable for commercial check Jig
- Power only mode
4.2.2. Check the power out & IR out - commercial
check jig
1) Connect each other RS232C port on the Commercial Check
JIG.
2) Press RED Color key on Service remote control.
3) Check the LED of jig board.
3) Check the LED of jig board.
- +12V / +5V LED (OK condition: Turn On)
- IR LED (OK condition: blinking)
- IR LED (OK condition: blinking)
4.2.3. Check the power out & IR out - mini jig
1) Connect mini jig on RS232c port.
2) Press RED Color key on Service remote control.
3) Check the LED of mini jig.
2) Press RED Color key on Service remote control.
3) Check the LED of mini jig.
4.3. Pro:Idiom
1) Connect the RF Cable.
2) Turn to the Pro:Idiom channel (No. 333).
3) Check the video & sound.
** Only displayed at “POWER ONLY” mode
2) Turn to the Pro:Idiom channel (No. 333).
3) Check the video & sound.
** Only displayed at “POWER ONLY” mode
4.4. Front LED Clock
1) Check the LED Clock in Power only mode.
Button of Vol. control
Waveform of Oscilloscope
UP(+)
DOWN(-)
Recommended Input Signal
: RF, 1 KHz, Sine wave
: RF, 1 KHz, Sine wave
5. Manual Adjustment
5.1. ADC Adjustment
5.1.1. Overview
ADC adjustment is needed to find the optimum black level and
gain in Analog-to-Digital device and to compensate RGB
deviation.
gain in Analog-to-Digital device and to compensate RGB
deviation.
5.1.2. Equipment & Condition
(1) Adjustment remote coontrol
(2) 801GF(802B, 802F, 802R) or MSPG925FA Pattern Generator
(2) 801GF(802B, 802F, 802R) or MSPG925FA Pattern Generator
- Resolution :
480i, Comp1 (MSPG-925FA: Model-209, Pattern-65)
1080p Comp1 (MSPG-925FA: Model: 225, Pattern-65)’
1080p RGB (MSPG-925FA: Model-225, Pattern-65)
1080p Comp1 (MSPG-925FA: Model: 225, Pattern-65)’
1080p RGB (MSPG-925FA: Model-225, Pattern-65)
- Pattern : Horizontal 100% Color Bar Pattern
- Pattern level: 0.7 ± 0.1 Vp-p
- Image
- Pattern level: 0.7 ± 0.1 Vp-p
- Image
(3) Must use standard cable
5.1.3. Adjust method
(1) ADC 480i/1080p Comp1, RGB
1) Check connected condition of Comp1 cable to the
equipment.
2) Give a 480i, Horizontal 100% Color Bar Pattern to
Comp1.(MSPG-925FA -> Model: 209, Pattern: 65)
3) Change input mode as Component1 and picture mode
as “Standard”.
4) Press the In-start Key on the ADJ remote control after at
least 1 min of signal reception. Then, select ‘7. External
ADC’. And press OK or Right key for going to sub menu.
ADC’. And press OK or Right key for going to sub menu.
5) Press OK in Comp 480i menu.
6) Give a 1080p Mode, Horizontal 100% Color Bar Pattern
6) Give a 1080p Mode, Horizontal 100% Color Bar Pattern
to Comp1. (MSPG-925A -> Model: 225, Pattern: 65)
7) Press OK in Comp 1080p menu.
8) Press OK in RGB menu.
9) If ADC Comp is successful, “ADC Component Success”
8) Press OK in RGB menu.
9) If ADC Comp is successful, “ADC Component Success”
is displayed.
If ADC calibration is failure, “ADC Component Fail” is
displayed.
displayed.
10) If ADC calibration is failure, after recheck ADC pattern
or condition, retry calibration
11) If ADC RGB is successful, “ADC RGB Success” is
displayed. If ADC calibration is failure, “ADC RGB Fail”
is displayed.
is displayed.
12) If ADC calibration is failure, after recheck ADC pattern
or condition, retry calibration Error message refer to 5).
5.2. EDID(The Extended Display Identification
Data)/DDC(Display Data Channel) download
(1) Overview
It is a VESA regulation. A PC or a MNT will display an
optimal resolution through information sharing without any
necessity of user input. It is a realization of “Plug and Play”.
optimal resolution through information sharing without any
necessity of user input. It is a realization of “Plug and Play”.
(2) Equipment
- Since embedded EDID data is used, EDID download JIG,
HDMI cable and D-sub cable are not need.
- Adjustment remote control
(3) Download method
1) Press ADJ key on the Adjustment remote control
2) Select EDID D/L menu.
3) By pressing Enter key, EDID download will begin.
4) If Download is successful, OK is display, but If
2) Select EDID D/L menu.
3) By pressing Enter key, EDID download will begin.
4) If Download is successful, OK is display, but If
Download is failure, NG is displayed.
5) If Download is failure, Re-try download.
<Caution>
When EDID Download, must remove RGB/HDMI Cable.
When EDID Download, must remove RGB/HDMI Cable.
(4) EDID DATA
A
HDMI
A
RGB
- 10 -
D-sub to D-sub
DVI-D to HDMI or HDMI to HDMI
For HDMI EDID
For Analog EDID
0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F
0x00 00
FF
FF
FF
FF
FF
FF
00
1E
6D
ⓐ
ⓑ
0x01
ⓒ
01
03
80
10
09
78
0A
EE
91
A3
54
4C
99
26
0x02 0F
50
54
A1
08
00
71
4F
81
80
01
01
01
01
01
01
0x03 01
01
01
01
01
01
02
3A
80
18
71
38
2D
40
58
2C
0x04 45
00
A0
5A
00
00
00
1E
01
1D
00
72
51
D0
1E
20
0x05 6E
28
55
00
A0
5A
00
00
00
1E
00
00
00
FD
00
3A
0x06 3E
1E
53
10
00
0A
20
20
20
20
20
20
ⓓ
0x07
ⓓ
01
ⓔ
0x00 02
03
26
F1
4E
10
1F
84
13
05
14
03
02
12
20
21
0x01 22
15
01
26
15
07
50
09
57
07
67
ⓕ
0x02
ⓕ
E3
05
03
01
01
1D
80
18
71
1C
16
20
58
2C
0x03 25
00
A0
5A
00
00
00
9E
01
1D
00
80
51
D0
1A
20
0x04 6E
88
55
00
A0
5A
00
00
00
1A
02
3A
80
18
71
38
0x05 2D
40
58
2C
45
00
A0
5A
00
00
00
1E
66
21
50
B0
0x06 51
00
1B
30
40
70
36
00
A0
5A
00
00
00
1E
00
00
0x07 00
00
00
00
00
00
00
00
00
00
00
00
00
00
01
ⓔ2
0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F
0x00 00
FF
FF
FF
FF
FF
FF
00
1E
6D
ⓐ
ⓑ
0x01
ⓒ
01
03
68
10
09
78
0A
EE
91
A3
54
4C
99
26
0x02 0F
50
54
A1
08
00
81
80
61
40
45
40
31
40
01
01
0x03 01
01
01
01
01
01
02
3A
80
18
71
38
2D
40
58
2C
0x04 45
00
A0
5A
00
00
00
1E
01
1D
00
72
51
D0
1E
20
0x05 6E
28
55
00
A0
5A
00
00
00
1E
00
00
00
FD
00
3A
0x06 3E
1E
53
10
00
0A
20
20
20
20
20
20
ⓓ
0x07
ⓓ
00
ⓔ3
Click on the first or last page to see other 47LV375H (CHASSIS:LD03X) service manuals if exist.