DOWNLOAD LG 47LN5700 / 47LN570T / 47LN570Y / 47LN5710 (CHASSIS:LB33B) Service Manual ↓ Size: 11.02 MB | Pages: 119 in PDF or view online for FREE

Model
47LN5700 47LN570T 47LN570Y 47LN5710 (CHASSIS:LB33B)
Pages
119
Size
11.02 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / LCD
File
47ln5700-47ln570t-47ln570y-47ln5710-chassis-lb33b.pdf
Date

LG 47LN5700 / 47LN570T / 47LN570Y / 47LN5710 (CHASSIS:LB33B) Service Manual ▷ View online

- 5 -
IC Remove/Replacement
Some chassis circuit boards have slotted holes (oblong) through 
which the IC leads are inserted and then bent flat against the cir-
cuit foil. When holes are the slotted type, the following technique 
should be used to remove and replace the IC. When working with 
boards using the familiar round hole, use the standard technique 
as outlined in paragraphs 5 and 6 above.
Removal
1.  Desolder and straighten each IC lead in one operation by 
gently prying up on the lead with the soldering iron tip as the 
solder melts.
2.  Draw away the melted solder with an anti-static suction-type 
solder removal device (or with solder braid) before removing 
the IC.
Replacement
1. Carefully insert the replacement IC in the circuit board.
2.  Carefully bend each IC lead against the circuit foil pad and 
solder it.
3. Clean the soldered areas with a small wire-bristle brush.
(It is not necessary to reapply acrylic coating to the areas).
"Small-Signal" Discrete Transistor
Removal/Replacement
1.  Remove the defective transistor by clipping its leads as close 
as possible to the component body.
2.  Bend into a "U" shape the end of each of three leads remain-
ing on the circuit board.
3. Bend into a "U" shape the replacement transistor leads.
4.  Connect the replacement transistor leads to the corresponding 
leads extending from the circuit board and crimp the "U" with 
long nose pliers to insure metal to metal contact then solder 
each connection.
Power Output, Transistor Device
Removal/Replacement
1. Heat and remove all solder from around the transistor leads.
2. Remove the heat sink mounting screw (if so equipped).
3.  Carefully remove the transistor from the heat sink of the circuit 
board.
4. Insert new transistor in the circuit board.
5. Solder each transistor lead, and clip off excess lead.
6. Replace heat sink.
Diode Removal/Replacement
1.  Remove defective diode by clipping its leads as close as pos-
sible to diode body.
2.  Bend the two remaining leads perpendicular y to the circuit 
board.
3.  Observing diode polarity, wrap each lead of the new diode 
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5.  Inspect (on the circuit board copper side) the solder joints of 
the two "original" leads. If they are not shiny, reheat them and 
if necessary, apply additional solder.
Fuse and Conventional Resistor
Removal/Replacement
1.  Clip each fuse or resistor lead at top of the circuit board hollow 
stake.
2.  Securely crimp the leads of replacement component around 
notch at stake top.
3.  Solder the connections.
CAUTION: Maintain original spacing between the replaced 
component and adjacent components and the circuit board to 
prevent excessive component temperatures.
Circuit Board Foil Repair
Excessive heat applied to the copper foil of any printed circuit 
board will weaken the adhesive that bonds the foil to the circuit 
board causing the foil to separate from or "lift-off" the board. The 
following guidelines and procedures should be followed when-
ever this condition is encountered.
At IC Connections
To repair a defective copper pattern at IC connections use the 
following procedure to install a jumper wire on the copper pattern 
side of the circuit board. (Use this technique only on IC connec-
tions).
1.  Carefully remove the damaged copper pattern with a sharp 
knife. (Remove only as much copper as absolutely necessary).
2.  carefully scratch away the solder resist and acrylic coating (if 
used) from the end of the remaining copper pattern.
3.  Bend a small "U" in one end of a small gauge jumper wire and 
carefully crimp it around the IC pin. Solder the IC connection.
4.  Route the jumper wire along the path of the out-away copper 
pattern and let it overlap the previously scraped end of the 
good copper pattern. Solder the overlapped area and clip off 
any excess jumper wire.
At Other Connections
Use the following technique to repair the defective copper pattern 
at connections other than IC Pins. This technique involves the 
installation of a jumper wire on the component side of the circuit 
board.
1.  Remove the defective copper pattern with a sharp knife.
Remove at least 1/4 inch of copper, to ensure that a hazardous 
condition will not exist if the jumper wire opens.
2.  Trace along the copper pattern from both sides of the pattern 
break and locate the nearest component that is directly con-
nected to the affected copper pattern.
3.  Connect insulated 20-gauge jumper wire from the lead of the 
nearest component on one side of the pattern break to the 
lead of the nearest component on the other side.
Carefully crimp and solder the connections.
CAUTION: Be sure the insulated jumper wire is dressed so the 
it does not touch components or sharp edges.
- 6 -
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application range
This  specification  is  applied  to  the  LED  TV  used  LB33B 
chassis.
2. Requirement for Test
Each part is tested as below without special appointment.
1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C
2) Relative Humidity: 65 % ± 10 %
3) Power Voltage
: Standard input voltage (AC 100-240 V~, 50/60 Hz)
* Standard Voltage of each products is marked by models.
4)  Specification  and  performance  of  each  parts  are  followed 
each  drawing  and  specification  by  part  number  in 
accordance with BOM.
5)  The receiver must be operated for about 20 minutes prior to 
the adjustment.
3. Test method
1) Performance: LGE TV test method followed 
2) Demanded other specification 
- Safety : CE, IEC specification
- EMC : CE, IEC 
4. Model General Specification
No.
Item
Specification
Remarks
1
Market
(PAL/DVB Market)
Australia/New Zealand(AU), Singapore(SG), 
Indonesia(ID),Malaysia(MY), Vietnam(VN), South 
only Analog for A-ASIA
2
Broadcasting system
1) PAL/SECAM-B/G/D/K
2) PAL-I/II
3) NTSC-M
4) DVB-T
PAL for NZ/SG
3
Channel Storage
ATV – 135EA, DTV – 1000EA
4
Receiving system
Analog : Upper Heterodyne
Digital : COFDM(DVB-T)
► DVB-T
- Guard Interval(Bitrate_Mbit/s)
  1/4, 1/8, 1/16, 1/32
- Modulation : Code Rate
  QPSK : 1/2, 2/3, 3/4, 5/6, 7/8
  16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
  64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
5.
Video Input RCA 
PAL, SECAM, NTSC
4 System : PAL, SECAM, NTSC, PAL60
6
Component Input 
Y/Pb/Pr
7
Head phone out
Antenna, AV1, Component, HDMI1, 
HDMI2, HDMI3, USB1, USB2, USB3
8
HDMI Input 
HDMI1-DTV,HDMI2-DTV
HDMI3-DTV
PC(HDMI Ver. 1.4)
Support HDCP
9
Audio Input
DVI Audio
Component
AV1
10
SPDIF out 
SPDIF out
11
USB Input
For My Media(Movie/Photo/Music List)
or For SVC
- 7 -
5. Component Video Input (Y, P
b
, P
r
)
No.
Resolution
H-freq(kHz)
V-freq(Hz)
Propose
1.
720×480
15.73
60.00
SDTV, DVD 480i
2.
720×480
15.63
59.94
SDTV, DVD 480i
3.
720×480
31.47
59.94
480p
4.
720×480
31.50
60.00
480p
5.
720×576
15.625
50.00
SDTV, DVD 625 Line
6.
720×576
31.25
50.00
HDTV 576p
7.
1280×720
45.00
50.00
HDTV 720p
8.
1280×720
44.96
59.94
HDTV 720p
9.
1280×720
45.00
60.00
HDTV 720p
10.
1920×1080
31.25
50.00
HDTV 1080i
11.
1920×1080
33.75
60.00
HDTV 1080i
12.
1920×1080
33.72
59.94
HDTV 1080i
13.
1920×1080
56.250
50
HDTV 1080p
14.
1920×1080
67.5
60
HDTV 1080p
- 8 -
6.2. PC mode
No.
Resolution
H-freq(kHz)
V-freq(Hz)
Propose
Remark
1
640 x 350 @70Hz
31.468
70.09
EGA
2
720 x 400 @70Hz
31.469
70.08
DOS
3
640 x 480 @60Hz
31.469
59.94
VESA(VGA)
4
800 x 600 @60Hz
37.879
60.31
VESA(SVGA)
5
1024 x 768 @60Hz
48.363
60
VESA(XGA)
6
1152 x 864 @60Hz
54.348
60.053
VESA
7
1280 x 1024 @60Hz
63.981
60.02
VESA(SXGA)
FHD only(Support to HDMI-PC)
8
1360 x 768 @60Hz
47.712
60.015
VESA(WXGA)
9
1920 x 1080 @60Hz
67.5
60
WUXGA(Reduced Blanking) FHD only
No.
Resolution
H-freq(kHz)
V-freq(Hz)
Pixel clock(MHz)
Propose
1
640*480
31.469 / 31.5
59.94 / 60
SDTV 480P
2
720*480
31.469 / 31.5
59.94 / 60
27.00/27.03
SDTV 480P
3
720*576
31.25
50
54
SDTV 576P
4
720*576
15.625
50
SDTV 576I
5
1280*720
37.500
50
74.25
HDTV 720P
6
1280*720
44.96 / 45
59.94 / 60
74.17/74.25
HDTV 720P
7
1920*1080
33.72 / 33.75
59.94 / 60
74.17/74.25
HDTV 1080I
8
1920*1080
28.125
50.00
74.25
HDTV 1080I
9.
1920*1080
26.97 / 27
23.97 / 24
74.17/74.25
HDTV 1080P
10
1920*1080
25
HDTV 1080P
11
1920*1080
33.716/ 33.75
29.976/30.00
74.25
HDTV 1080P
12
1920*1080
56.250
50
148.5
HDTV 1080P
13
1920*1080
67.43 / 67.5
59.94 / 60
148.35/148.50
HDTV 1080P
6. HDMI Input
6.1. DTV mode
Page of 119
Display

Click on the first or last page to see other 47LN5700 / 47LN570T / 47LN570Y / 47LN5710 (CHASSIS:LB33B) service manuals if exist.