LG 47LM8600 (CHASSIS:LT23E) Service Manual ▷ View online
- 3 -
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
An
isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this
protects the technician from accidents resulting in personal injury
from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitry that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown,
replace it with the specified.
When replacing a high wattage resistor (Oxide Metal Film Resistor,
over 1 W), keep the resistor 10 mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Before returning the receiver to the customer,
always perform an
AC leakage current check on the exposed
metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical
shock.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1 M
Ω and 5.2 MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Leakage Current Hot Check
(See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC voltage
measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
0.5 mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit
IMPORTANT SAFETY NOTICE
SAFETY PRECAUTIONS
- 4 -
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application range
This spec sheet is applied to the LCD TV used LT23E chassis.
2. Test condition
Each part is tested as below without special notice.
1) Temperature : 25 ºC ± 5 ºC (77 ºF ± 9 ºF), CST : 40 ºC±5 ºC
2) Relative Humidity: 65 % ± 10 %
3) Power Voltage : Standard input voltage (100~240V@
50/60Hz)
4) Specification and performance of each parts are followed
each drawing and specification by part number in
accordance with BOM.
5) The receiver must be operated for about 5 minutes prior to
the adjustment.
3. Test method
1) Performance: LGE TV test method followed
2) Demanded other specification
- Safety : CE, IEC specification
- EMC : CE, IEC
4. General Specification
No
Item
Specification
Remark
1.
Display Screen Device
54.64” Color Active Matrix LCD Module
46.96” Color Active Matrix LCD Module
46.96” Color Active Matrix LCD Module
72.07” Color Active Matrix LCD Module
LC550DUT-SEF1(55LM9600-DA)
LC470DUT-SEF1(47LM9600-DA)
LC470EUH-KEF1(47LM8600-DA)
LC720DUC-SDF1(72LM9500-DA)
2.
Aspect Ratio
16:9
All
3.
LCD Module
54.64” WUXGA diagonal LCD
46.96” WUXGA diagonal LCD
46.96” WUXGA diagonal LCD
72.07” WUXGA diagonal LCD
LC550DUT-SEF1(55LM9600-DA)
LC470DUT-SEF1(47LM9600-DA)
LC470EUH-KEF1(47LM8600-DA)
LC720DUC-SDF1(72LM9500-DA)
4.
Operating Environment
TFT
1) Temp. : 0 ~ 40 deg
2) Humidity : 0 ~ 85%
LGE SPEC
ALEF
Temp. : 0 ~ 50 deg
Humidity : 20 ~ 90%
5.
Storage Environment
TFT
Temp. : -20 ~ 60 deg
Humidity : 10 ~ 90%
LGE SPEC
ALEF
Temp. : -20 ~ 60 deg
Humidity : 10 ~ 90%
6.
Input Voltage
AC100 ~ 240V, 50/60Hz
7.
Power Consumption(Max) =
LCD(Module) + Backlight(LED)
T480
54.64” 190
W
LC550DUT-SEF1(55LM9600-DA)
46.96” 81
W
LC470DUT-SEF1(47LM9600-DA)
72.07” 385
W
LC720DUC-SDF1(72LM9500-DA)
T240
46.96” 129
W
LC470EUH-KEF1(47LM8600-DA)
- 5 -
8.
LCD Module
Size
Maker
Inch
(H) × (V) × (D)
LGD
54.64”
1217 x 689.9 x 1.5
LC550DUT-SEF1(55LM9600-DA)
46.96”
1046.68 x 594.02 x1.5 LC470DUT-SEF1(47LM9600-DA)
46.96”
1059.5 x 616.2 x 20.7 LC470EUH-KEF1(47LM8600-DA)
72.07”
1666.0 x 968.0 x 54.0 LC720DUC-SDF1(72LM9500-DA)
Pixel Pitch
Maker
Inch
(H) × (V) × (D)
LGD
47”
0.5415 x 0.5415
LC470DUT-SEF1(47LM9600-DA)
55”
0.630 x 0.630
LC550DUT-SEF1(55LM9600) ALEF 3D-PG T480
47”
0.5415 x 0.5415
LC470EUH-KEF1(47LM8600-DA)
72.07”
0.831 x 0.831
LC720DUC-SDF1(72LM9500-DA)
Back Light
LGD
54.64”
ALEF
LC550DUT-SEF1(55LM9600) ALEF 3D-PG T480
46.96”
ALEF
LC470DUT-SEF1(47LM9600-DA)
46.96”
EDG-LED
LC470EUH-KEF1(47LM8600-DA)
72.07”
EDG-LED
LC720DUC-SDF1(72LM9500-DA)
4. General Specification
No
Item
Specification
Remark
1.
Display Screen Device
54.64” Color Active Matrix LCD Module
46.96” Color Active Matrix LCD Module
46.96” Color Active Matrix LCD Module
72.07” Color Active Matrix LCD Module
LC550DUT-SEF1(55LM9600-DA)
LC470DUT-SEF1(47LM9600-DA)
LC470EUH-KEF1(47LM8600-DA)
LC720DUC-SDF1(72LM9500-DA)
2.
Aspect Ratio
16:9
All
3.
LCD Module
54.64” WUXGA diagonal LCD
46.96” WUXGA diagonal LCD
46.96” WUXGA diagonal LCD
72.07” WUXGA diagonal LCD
LC550DUT-SEF1(55LM9600-DA)
LC470DUT-SEF1(47LM9600-DA)
LC470EUH-KEF1(47LM8600-DA)
LC720DUC-SDF1(72LM9500-DA)
4.
Operating Environment
TFT
1) Temp. : 0 ~ 40 deg
2) Humidity : 0 ~ 85%
LGE SPEC
ALEF
Temp. : 0 ~ 50 deg
Humidity : 20 ~ 90%
5.
Storage Environment
TFT
Temp. : -20 ~ 60 deg
Humidity : 10 ~ 90%
LGE SPEC
ALEF
Temp. : -20 ~ 60 deg
Humidity : 10 ~ 90%
6.
Input Voltage
AC100 ~ 240V, 50/60Hz
7.
Power Consumption(Max) =
LCD(Module) + Backlight(LED)
T480
54.64” 190
W
LC550DUT-SEF1(55LM9600-DA)
46.96” 81
W
LC470DUT-SEF1(47LM9600-DA)
72.07” 385
W
LC720DUC-SDF1(72LM9500-DA)
T240
46.96” 129
W
LC470EUH-KEF1(47LM8600-DA)
- 6 -
5. External Input Support Format
5.1. Component(Y, Pb, Pr)
5.2. RGB Input ( PC )
No.
Resolution
H-freq(kHz)
V-freq(Hz)
Remark
1.
720*480i
15.73
59.94
13.500
SDTV, DVD 480I(525I)
2
720*480i
15.73
60.00
13.514
SDTV, DVD 480I(525I)
3.
720*576i
15.625
50.00
13.500
SDTV, DVD 576I(625I) 50Hz
4
720*480p
31.47
59.94
27.000
SDTV 480P
5
720*480p
31.50
60.00
27.027
SDTV 480P
6
720*576p
31.25
50.00
27.000
SDTV 576P 50Hz
7
1280*720
44.96
59.94
74.176
HDTV 720P
8
1280*720
45.00
60.00
74.250
HDTV 720P
9
1280*720
37.50
50.00
74.25
HDTV 720P 50Hz
10
1920*1080
28.125
50.00
74.250
HDTV 1080I 50Hz,
11
1920*1080
33.72
59.94
74.176
HDTV 1080I
12
1920*1080
33.75
60.00
74.25
HDTV 1080I
13
1920*1080
26.97
23.976
63.296
HDTV 1080P
14
1920*1080
27.00
24.000
63.36
HDTV 1080P
15
1920*1080
33.71
29.97
79.120
HDTV 1080P
16
1920*1080
33.75
30.00
79.20
HDTV 1080P
17
1920*1080
56.25
50
148.5
HDTV 1080P
18
1920*1080
67.432
59.94
148.350
HDTV 1080P
19
1920*1080
67.5
60.00
148.5
HDTV 1080P
No
Resolution
H-freq(kHz)
V-freq.(Hz)
Pixel clock (MHz)
Proposed
Remark
1
640*350
31.468
70.09
25.174
EGA
For only DOS mode
2
720*400
31.469
70.08
28.321
DOS
For only DOS mode
3
640*480
31.469
59.94
25.17
VESA(VGA)
Input 848*480 60Hz,
852*480 60Hz
=> 640*480 60Hz Display
4
800*600
37.879
60.31
40.00
VESA(SVGA)
5.
1024*768
48.363
60.00
65.00
VESA(XGA)
6.
1152*864
54.348
60.053
80.00
VESA(XGA Plus)
7.
1360*768
47.712
60.015
85.50
VESA(WXGA)
FHD Only
8.
1920*1080
67.5
60.00
148.5
VESA(WUXGA)