LG 47LM8600 (CHASSIS:LC23E) Service Manual ▷ View online
LGE
Display Division
LG(53)
Establish : 11.08.18 32
Reform : 72
Reform : 72
LG Electronics
LC23E Product Specification
2) Dark room measure condition : Using touch type Color analyzer CA-210 Dark room in the non outside light
3) Bright room measure condition : In bright room of 150Lx illumination in the panel surface, locate a source of light on the above 45˚of the panel surface.
4) Test pattern and points (
Picture mode: Vivid
)
LDSCR
▣
3D Crosstalk
1) Test condition
- Source : HDMI 1080p
- Room light : 0 lux
- Warm up time : > 1 hour
- Measurement device : CS-1000 / PR-880
3D_측정기준
2) Test method
- Measurement Distance >50 cm / Measurement point : Center / Measurement view angle : < 1°
3) Test pattern and points
LGE
Display Division
LG(53)
Establish : 11.08.18 33
Reform : 72
Reform : 72
LG Electronics
LC23E Product Specification
4) Formula of crosstalk
* 3D Luminance = W
LR
+ W
RL
LGE
Display Division
LG(53)
Establish : 11.08.18 34
Reform : 72
Reform : 72
LG Electronics
LC23E Product Specification
10.3
SET Optical Feature
1) General feature
(Measurement Condition: Full white/ Dynamic)
(Measurement Condition: Full white/ Dynamic)
à
Measure the black luminance after 30 seconds.
Luminance (min)
C/R(min)
No
Item
Module
AV, COMPONENT, HDMI
AV, COMPONENT, HDMI
Remark
1
55LM9600-CA
LGD
200 ( 2D )
200
Except from the PC mode.
2
47LM8600-CA
LGD
200 ( 2D )
200
Except from the PC mode.
3
55LM8600-CA
LGD
200 ( 2D )
200
Except from the PC mode.
2) 3D Crosstalk
No.
Item
Specification
Min.
Typ.
Max.
Remark
1.
3D Crosstalk
1
3
%
11. Audio
11.1. Speaker component specification
No
Item
Min
Typ
Max
Unit
Measured
Result
Remark
1
Output range
10
14
W
8Ω Impedance
Full-range
72
90
108
Hz
2
fo
Woofer
120
150
180
Hz
Full-range
78
80
82
dB
3
SPL
Woofer
72
90
108
dB
11.2. Sound pressure Level
No
Item
Min
Typ
Max
Unit
Measured
Result
Remark
LGE
Display Division
LG(53)
Establish : 11.08.18 35
Reform : 72
Reform : 72
LG Electronics
LC23E Product Specification
1
Sound pressure
72
dB
- EQ on, Volume Max, AVL&Clear voice
off
off
11.3. General specification
No
Item
Min
Typ
Max
Unit
Remark
1
Auto Volume Level (AVL )
(1) the level changing between AVL on and off.
(2) the level changing at Start point and End point
(2) the level changing at Start point and End point
at AVL ON
PEQ on/off
<Test condition>
1. Before the Test (AutoVolume, PEQ, Bass EQ,
ClearVoice and Surround Effect are “off”)
* PEQ: Parametric Equalize
2. Open the test file, “ Stereo test(autovolume test).at27”
3. Check the reference. signal, the difference of volume
levels should be about 2dB.(Adjust Low Level Percentage
in Analog Generator)
4.Then, AutoVolume “ON” and capture the waveform.
5.Compare the captured waveform with the reference
waveform.
1. Before the Test (AutoVolume, PEQ, Bass EQ,
ClearVoice and Surround Effect are “off”)
* PEQ: Parametric Equalize
2. Open the test file, “ Stereo test(autovolume test).at27”
3. Check the reference. signal, the difference of volume
levels should be about 2dB.(Adjust Low Level Percentage
in Analog Generator)
4.Then, AutoVolume “ON” and capture the waveform.
5.Compare the captured waveform with the reference
waveform.
4.5
8.5
12.5
dBr
3.7
7.2
10.7
dBr
3
6
9
dBr
2.2
4.7
7.2
dBr
1.25
3.25
5.25
dBr
0.6
1.6
2.6
dBr
-0.5
0
0.5
dBr
-3.3
-2
-0.7
dBr
-6.5
-4
-1.5
dBr
-7.5
-5
-2.5
dBr
-11
-7
-3
dBr
-13.5
-9
-4.5
dBr
-16
-10
-4
dBr
PEQ off
<Test condition>
1. Before the Test (AutoVolume, PEQ, Bass EQ,
ClearVoice and Surround Effect are “off”)
2. Open the test file, “sound_effect_test.at27”
Source Output Level: 0.4mVrms
TV Set Output Level: 70mW±10mW(8ohm)
*PEQ: Parametric Equalize
3. Clear Voice Step:Off, +6 ~-6(13 Steps)
4. Capture the waveform.:
1. Before the Test (AutoVolume, PEQ, Bass EQ,
ClearVoice and Surround Effect are “off”)
2. Open the test file, “sound_effect_test.at27”
Source Output Level: 0.4mVrms
TV Set Output Level: 70mW±10mW(8ohm)
*PEQ: Parametric Equalize
3. Clear Voice Step:Off, +6 ~-6(13 Steps)
4. Capture the waveform.:
4
8.5
13
dBr
2.5
7
11.5
dBr
2
6
10
dBr
1.5
4.5
7.5
dBr
2
Clear Voice II
0.5
3
5.5
dBr
PEQ on
(Optional test)
(Optional test)
<Test condition>
1. Before the Test (AutoVolume, PEQ, Bass EQ,
ClearVoice and Surround Effect are “off”)
2. Open the test file, “sound_effect_test.at27”
Source Output Level: 0.4mVrms
1. Before the Test (AutoVolume, PEQ, Bass EQ,
ClearVoice and Surround Effect are “off”)
2. Open the test file, “sound_effect_test.at27”
Source Output Level: 0.4mVrms
Click on the first or last page to see other 47LM8600 (CHASSIS:LC23E) service manuals if exist.