DOWNLOAD LG 47LE5400 (CHASSIS:LA02D) Service Manual ↓ Size: 7.88 MB | Pages: 85 in PDF or view online for FREE

- 13 -

(1) Overview

It is a VESA regulation. A PC or a MNT will display an
optimal resolution through information sharing without any
necessity of user input. It is a realization of “Plug and Play”. 

(2) Equipment

• Since embedded EDID data is used, EDID download JIG,

HDMI cable and D-sub cable are not need.  

• Adjust by using remote controller.  

(3) Download method

1) Press Adj. key on the Adj. R/C, 
2) Select EDID D/L menu. 
3) By pressing Enter key, EDID download will begin 
4) If Download is successful, OK is display, but If

Download is failure, NG is displayed. 

5) If Download is failure, Re-try downloads. 

Caution) When EDID Download, must remove RGB/HDMI

Cable.

(4) EDID DATA 

- 14 -

(1) Overview

• W/B adj. Objective & How-it-works

- Objective: To reduce each Panel’s W/B deviation
- How-it-works: When R/G/B gain in the OSD is at 192, it

means the panel is at its Full Dynamic
Range. In order to prevent saturation of
Full Dynamic range and data, one of
R/G/B is fixed at 192, and the other two is
lowered to find the desired value.   

- Adj. condition : normal temperature

1) Surrounding Temperature: 25±5ºC
2) Warm-up time: About 5 Min
3) Surrounding Humidity: 20% ~ 80%

(2) Adj. condition and cautionary items 

• Lighting condition in surrounding area surrounding lighting

should be lower 10 lux.  Try to isolate adj. area into dark
surrounding. 

• Probe location: Color Analyzer (CA-210) probe should be

within 10cm and perpendicular of the module surface
(80°~ 100°) 

• Aging time 

1) After Aging Start, Keep the Power ON status during

5 Minutes. 

2) In case of LCD, Back-light on should be checked

using no signal or Full-white pattern. 

(3) Equipment

1)  Color Analyzer: CA-210 (NCG: CH 9 / WCG: CH12 /

LED : CH14) 

2) Adj. Computer (During auto adj., RS-232C protocol is

needed) 

3) Adjust Remocon
4) Video Signal Generator MSPG-925F 720p/216-Gray

(Model:217, Pattern:78) 

-> Only when internal pattern is not available

• Color Analyzer Matrix should be calibrated using CS-1000

(4) Equipment connection

(5) Adj. Command (Protocol)

1) RS-232C Command used during auto-adj. 

2) Adjustment Map

(6) Adj. method

• Auto adj. method

1) Set TV in adj. mode using POWER ON key
2) Zero calibrate probe then place it on the center of the

Display

3) Connect Cable(RS-232C)
4) Select mode in adj. Program and begin adj.
5) When adj. is complete (OK Sing), check adj. status pre

mode (Warm, Medium, Cool)

6) Remove probe and RS-232C cable to complete adj.

(7) Reference (White Balance Adj. coordinate and color

temperature)

• Luminance: 216 Gray
• Standard color coordinate and temperature using CS-

1000 

• Standard color coordinate and temperature using CA-210

(CH 14)

Co lo r An alyzer

 

Co m p ut er

 

Pat t ern Gen erat o r

 

RS -232C 

RS -232C 

RS -232C 

Probe

Signal Source

* If TV internal pattern is used, not needed

Connection Diagram of Automatic Adjustment

Mode

Color Coordination

Temp

∆

UV

x

y

COOL

0.269

0.273

13000K

0.0000

MEDIUM

0.285

0.293

9300K

0.0000

WARM

0.313

0.329

6500K

0.0000

Mode

Color Coordination

Temp

∆

UV

x

y

COOL

0.269±0.002

0.273±0.002

13000K

0.0000

MEDIUM

0.285±0.002

0.293±0.002

9300K

0.0000

WARM

0.313+0.002

0.329±0.002

6500K

0.0000

- 15 -

• Standard color coordinate and temperature using CA-

210(CH 14) – by aging time 

1) Edge/IOP LED models 

(1) Overview

•  Tool option selection is only done for models in Non-USA

• Applied model: LA02D and LA02E Chassis applied to

CANADA and MEXICO 

(2) Country Group selection 

•  Press ADJ key on the Adj. R/C, and then select Country

Group Menu 

•  Depending on destination, select KR or US, then on the

lower Country option, select US, CA, MX.  Selection is
done using +, - KEY 

(3)  Tool Option Inspection  

•  Press Adj. key on the Adj. R/C, and then check Tool

option.  

5.3.1. Edge LED models with local dimming 
(1) Press  ‘TILT” key of the Adj. R/C and check moving

patterns. The black bar patterns moves from left to right.    

If local dimming function does not work, a whole screen
shows full white. 

5.3.2. IOP LED models with local dimming 
(1) Press ‘TILT” key of the Adj. R/C and check moving
patterns. The black cross-bar patterns moves from top-left to
Bottom-right. If local dimming function does not work, a whole
screen shows full white. 

• After final inspection, press In-Stop key of the Adj. R/C and

check that the unit goes to Stand-by mode. 

- 16 -

6.1.1. GND & HI-POT auto-check preparation  

(1) Check the POWER CABLE and SIGNAL CABE

insertion condition 

6.1.2. GND & HI-POT auto-check  

(1) Pallet moves in the station. (POWER CORD / AV
CORD is tightly inserted) 
(2) Connect the AV JACK Tester. 
(3) Controller (GWS103-4) on. 
(4) GND Test (Auto)  

- If Test is failed, Buzzer operates. 
- If Test is passed, execute next process (Hi-pot test).

(Remove A/V CORD from A/V JACK BOX)  

(5) HI-POT test (Auto) 

- If Test is failed, Buzzer operates. 
- If Test is passed, GOOD Lamp on and move to next

process automatically. 

• TEST voltage

- GND: 1.5KV/min at 100mA
- SIGNAL: 3KV/min at 100mA

• TEST time: 1 second
• TEST POINT

- GND TEST = POWER CORD GND & SIGNAL CABLE

METAL GND

NEUTRAL

• LEAKAGE CURRENT: At 0.5mArms