LG 42PJ350R-ZA / 42PJ351R-ZC / 42PJ352R-ZD / 42PJ353R-ZB (CHASSIS:PP01B) Service Manual ▷ View online
- 13 -
8-4. Adjustment of Area option.
(1) Area Option Adjustment following BOM
(Including SKD models )
Tool Option
Area Option
Option 1
Option 2
Option 3 ( Available for EU & Non EU model )
Area Option
Option 1
Option 2
Option 3 ( Available for EU & Non EU model )
* Profile : Must be changed the option value because being
different with some setting value depend on module,
inch and market
inch and market
* Equipment : Adjustment Remote Controller
1) Push the IN-START key in the Adjust R/C.
2) Enter Password number. The value of Password is “0 0
2) Enter Password number. The value of Password is “0 0
0 0”.
3) Input the Area Option Number that was specified in the
BOM, into the Shipping area.
4) Select “Area Option” by using
D
/
E
(CH+/-) key, and
press the number key(0~9) consecutively
ex) If the value of Area Option 40, input the data using
number key “40” (Fig. 3)
Caution:
- Although it is SKD model, adjust area option in SET
assemmbly process.
- Don’t Push “IN-STOP” key after PCB assembly
adjustment.
9. Adjustment of White Balance
9-1. Required Equipment
(1) Remote controller for adjustment
(2) Color Analyzer ( CS-1000, CA-100,100+,CA-210 or same
(2) Color Analyzer ( CS-1000, CA-100,100+,CA-210 or same
produc : CH 10 (PDP)
lease adjust CA-210, CA-100+ by CS-1000 before
measuring
measuring
(3) Auto W/B adjustment instrument(only for Auto adjustment)
9-2. AUTO White Balance Process.
Before Adjust of White Balance, Please press POWER ONLY
key
key
Adjust Process will start by execute RS232C Command.
O
CS-1000/CA-100+/CA-210(CH 10) White balance adjustment
coordinates and color temperature.
coordinates and color temperature.
9-3. Manual W/B process (using adjusts
Remote control)
(1) Enter ‘PICTURE RESET’ on Picture Mode, then turn off
Fresh Contrast and Fresh colour in Advanced Control
(2) After enter Service Mode by pushing “ADJ” key,
(3) Enter White Pattern off of service mode, and change off ->
(3) Enter White Pattern off of service mode, and change off ->
on.
(4) Enter “W/B ADJUST” by pushing “
G
” key at “3. W/B
ADJUST”.
(5) Adjust W/B DATA, for all CSM, choose ‘COPY ALL’
* Gain Max Value is 192. So, Never make any Gain Value
over 192 and please fix one Value on 192, between R, G
and B.
and B.
..
CSM Color Coordinate
Temp
Color Coordinate
x
y
Cool
0.276
0.283
11000K
0.002
Medium
0.285
0.293
9300K
0.002
Warm
0.313
0.329
6500K
0.002
Min
Tpy
Max
R-GAIN
0
192
192
G-GAIN
0
192
192
B-GAIN
0
192
192
- 14 -
* Auto-control interface and directions
(1) Adjust in the place where the influx of light like floodlight
around is blocked. (Illumination is less than 10ux).
(2) Measure and adjust after sticking the Color Analyzer
(CA-100+, CA210 ) to the side of the module.
(3) Aging time
After aging start, keep the Power on (no suspension of
power supply) and heat-run over 5 minutes
power supply) and heat-run over 5 minutes
*Above optical characteristics are should be measured by
following condition.
O
DDC Adjustment Command Set
Measured Mode
Picture Mode
Vivid
Fresh Contrast
Off
Fresh Color
Off
Smart Power Saving
Off
Adjustment
Adjustment
Adjustment
- 15 -
BLOCK DIAGRAM
- 16 -
EXPLODED VIEW
200
120
305
300
400
580
301
302
303
304
202
240
520
207
206
204
203
201
501
590
570
602
601
205
310
910
900
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
IMPORTANT SAFETY NOTICE
A10
A9
LV1
A12
A21
A2
Click on the first or last page to see other 42PJ350R-ZA / 42PJ351R-ZC / 42PJ352R-ZD / 42PJ353R-ZB (CHASSIS:PP01B) service manuals if exist.