LG 42PC5D-AB (CHASSIS:PB73B) Service Manual ▷ View online
- 6 -
A
EDID for HDMI-3 (DDC (Display Data Channel) Data)
EDID table =
EDID table =
A
EDID for RGB (DDC (Display Data Channel) Data)
EDID table =
EDID table =
4. POWER PCB Assy Voltage
Adjustments
(Va, Vs Voltage adjustments)
4-1. Test Equipment :
D.M.M. 1EA
4-2.Connection Diagram for Measuring
: refer to Fig.2
4-3. Adjustment Method
(1) Va Adjustment
1) After receiving 100% Full White Pattern, HEAT RUN.
2) Connect + terminal of D.M.M to Va pin of P812, connect
2) Connect + terminal of D.M.M to Va pin of P812, connect
- terminal to GND pin of P812.
3) After turning VR901, voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top.
(Deviation; ±0.5V)
(Deviation; ±0.5V)
(2) Vs Adjustment
1) Connect + terminal of D.M.M to Vs pin of P812, connect
– terminal to GND pin of P812.
2) After turning VR951, voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top.
(Deviation; ±0.5V)
(Deviation; ±0.5V)
5. MST3361M-Set Adjustment
5-1. Synopsis
MST3361M-Set adjustment to set the black level and the Gain
of optimum with an automatic movement from the analog =>
digital converter.
of optimum with an automatic movement from the analog =>
digital converter.
5-2. Test Equipment
Service R/C, 801GF(802B,802F,802R),
MSPG-925FA,MSPG-1025D Pattern Generator.
( 480i, 1080p Horizontal 60Hz Color Bar Pattern output will be
possible and the output level will accurately have to be
revised with 0.7±0.1Vp-p)
* It should be checked because the above pattern may be
different according to the model and the pattern of the used
equipment.
MSPG-925FA,MSPG-1025D Pattern Generator.
( 480i, 1080p Horizontal 60Hz Color Bar Pattern output will be
possible and the output level will accurately have to be
revised with 0.7±0.1Vp-p)
* It should be checked because the above pattern may be
different according to the model and the pattern of the used
equipment.
5-3. Adjustment method
(1) Component1 adjustment method.
1) Select Component1 as the input with Color Bar Pattern
in 480i 60Hz mode and select ‘Component1’ on screen.
2) After receiving signal for at least 1 second, press the
ADJ Key on the Service R/C to enter the ‘Ez - Adjust’
and select the ‘1. ADC 480i Comp1’. Pressing the Vol+
Key to adjust the component1.
and select the ‘1. ADC 480i Comp1’. Pressing the Vol+
Key to adjust the component1.
3) When the adjustment is over, 'ADC Component1
Success’ is displayed.
4) When the adjustment is not normally completed, a
message saying ‘ADC Component1 480i Fail’ is
displayed. When the component is not connected, a
message saying ‘Component1 Not Connected’, when
the input format is not 480i, a message saying ‘Not
Valid Format’ and when the input signal is not coming
out, a message saying ‘Check Signal Status’ is
displayed for 1 second.
(MSPG-925FA : -> model : 209, pattern : 65)
displayed. When the component is not connected, a
message saying ‘Component1 Not Connected’, when
the input format is not 480i, a message saying ‘Not
Valid Format’ and when the input signal is not coming
out, a message saying ‘Check Signal Status’ is
displayed for 1 second.
(MSPG-925FA : -> model : 209, pattern : 65)
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
00 FF FF FF FF FF
FF 00
1E
6D
01
00
01
01
01
01
10
00 11 01
03
80
73
41 96
0A
CF 74
A3
57 4C B0 23
20
09 48 4C AF CE 00
31 40
45
40
61
40
81
80
A9 40
30 D1 C0 01
01
01
01
66 21
50
B0
51
00
1B 30
40
70
40
36 00 C4 8E 21
00
00 1A
02
3A
80
18
71
38
2D 40
50
58 2C 45
00 C4 8E
21 00
00
1E
00
00
00 FD
00
30
60
58 1F 64
11
00
0A
20 20
20
20
20
20
00
00
00 FC
70
00 4C 47
20
54
56
0A 20
20
20
20
20
20
20
01
00
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
02 03 1E F1 4E
20
22 10
1F
01
02
03
04
05
12
93
10
14 07 16
23
15
07
50 66
03
0C
00
30
00
80
01 1D
20
00 72 51 D0 1E
20
6E 28
55
00
C4 8E
21
00
00 1E
30
01 1D 80
18
71
1C
16 20
58
2C
25
00 C4 8E
21
00
40
00 9E 8C 0A D0
90
20 40
31
20
0C
40
55
00
4C 6C
50
42 00 00
18
01
1D
00 BC 52
D0 1E
20
B8 28
55
40
60 C4 8E 21
00
00
1E
01 1D
80
D0
72
1C 16
20
10 2C
70
25 80 C4 8E 21
00
00 9E
00
00
00
00
00
00
00
38
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
00 FF FF FF FF FF
FF 00
1E
6D
01
00
01
01
01
01
10
0E 11 01
03
18
73
41 96
0A
CF 74
A3
57 4C B0 23
20
09 48 4C AF CF 00
31 40
45
40
61
40
81
80
A9 40
30 D1 C0 01
01
01
01
66 21
50
B0
51
00
1B 30
40
70
40
36 00 C4 8E 21
00
00 1A
02
3A
80
18
71
38
2D 40
50
58 2C 45
00 C4 8E
21 00
00
1E
00
00
00 FD
00
30
60
58 1F 64
11
00
0A
20 20
20
20
20
20
00
00
00 FC
70
00 4C 47
20
54
56
0A 20
20
20
20
20
20
20
01
59
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
02 03 04
00 0E
1F
00 80
51
00
1E
30
40
80
37
00
10 C4 8E 21
00
00
1C
00 00
00
00
00
00
00
00
00
00
20
00 00 00
00
00
00
00 00
00
00
00
00
00
00
00
00
30
00 00 00
00
00
00
00 00
00
00
00
00
00
00
00
00
40
00 00 00
00
00
00
00 00
00
00
00
00
00
00
00
00
50
00 00 00
00
00
00
00 00
00
00
00
00
00
00
00
00
60
00 00 00
00
00
00
00 00
00
00
00
00
00
00
00
00
70
00 00 00
00
00
00
00 00
00
00
00
00
00
00
00
25
<Fig.3> Adjust Pattern : 480i, 1080p 60Hz Color Bar Pattern
(Fig.2) Connection diagram of power adjustment for measuring
- 7 -
(2) Component1, RGB adjustment method.
1) Select Component1, RGB as the input with Color Bar
Pattern in 1080p 60Hz mode and select ‘Component1’
as input mode.
as input mode.
2) After receiving signal for at least 1 second, press the
ADJ Key on the Service R/C to enter the ‘Ez - Adjust’
and select the ‘2. ADC 480i Comp1/RGB’. Pressing the
Vol+ Key to adjust the component1.
and select the ‘2. ADC 480i Comp1/RGB’. Pressing the
Vol+ Key to adjust the component1.
3) When the adjustment is normally completed, the
message ‘ADC Component1 Success’ is displayed, or if
not, the message ‘ADC Component1 1080P Fail’ is
displayed. After adjusting the Component1 is
completed, it is automatically switched to the RGB-DTV
mode, and the RGB adjustment starts. If adjusting is
normally completed, the message ‘ADC RGB 1080P
Success’ is displayed.
not, the message ‘ADC Component1 1080P Fail’ is
displayed. After adjusting the Component1 is
completed, it is automatically switched to the RGB-DTV
mode, and the RGB adjustment starts. If adjusting is
normally completed, the message ‘ADC RGB 1080P
Success’ is displayed.
4) When the adjustment is not normally completed, check
the pattern or the adjustment condition, and then adjust
it again. The error message is same to (4)) of (1)
it again. The error message is same to (4)) of (1)
5) After adjustment is complete, exit the adjustment mode
by pressing the ADJ KEY.
(MSPG-925FA : -> model : 225, pattern : 65)
(MSPG-925FA : -> model : 225, pattern : 65)
6. Video Set Adjustment
It is the adjustment to reduce the color difference of the RF
and the video signal, which adjusts Analog RF, AV-PAL, and
AV-NTSC.
and the video signal, which adjusts Analog RF, AV-PAL, and
AV-NTSC.
6-1. Adjustment method
(1) Analog RF and AV-PAL adjustment method.
1) Connect the Video Signal Generator (Master) to the AV
input of the TV via the AV output. At this time, when
entering the input pattern with Model : 202(PAL) and
Pattern : 33(100% color Bar), the following screen is
displayed.
entering the input pattern with Model : 202(PAL) and
Pattern : 33(100% color Bar), the following screen is
displayed.
* It should be checked because the above pattern may be
different according to the model and the pattern of the used
equipment.
different according to the model and the pattern of the used
equipment.
2) After entering the in-house signal, when it is checked
that the signal is received, press the ADJ KEY of the
adjusting R/C to enter into ‘EZ-ADJUST’ Select ‘3.
Adjust RF and AV_PAL’ and press the right arrow key
(
adjusting R/C to enter into ‘EZ-ADJUST’ Select ‘3.
Adjust RF and AV_PAL’ and press the right arrow key
(
G
) to enter into the adjustment mode.
3) When it enters into the adjustment mode, the screen is
automatically switched to TV 3CH and the following
window is displayed.
window is displayed.
4) When the automatic adjustment starts, the main screen
is adjusted, and if adjusting is completed, the message
‘RF-PAL Configuration Success’ is displayed. If
adjusting is failed, the message ‘RF-PAL Configuration
Fail’ is displayed.
‘RF-PAL Configuration Success’ is displayed. If
adjusting is failed, the message ‘RF-PAL Configuration
Fail’ is displayed.
5) When the automatic adjustment of the RF signal is
completed, it is automatically switched to AV1 Mode
and the automatic adjustment is performed to the AV-
PAL. When the automatic adjustment is completed, the
message ‘AV-PAL Configuration Success’ is displayed.
If the adjustment is failed, the message ‘AV-PAL
Configuration Fail’ is displayed.
and the automatic adjustment is performed to the AV-
PAL. When the automatic adjustment is completed, the
message ‘AV-PAL Configuration Success’ is displayed.
If the adjustment is failed, the message ‘AV-PAL
Configuration Fail’ is displayed.
(2) AV-NTSC adjustment method.
1) Connect the Video Signal Generator (Master) to the AV
input of the TV via the AV output. At this time, when
entering the input pattern with Model : 201(NTSC) and
Pattern : 33(100% color Bar), the following screen is
displayed.
entering the input pattern with Model : 201(NTSC) and
Pattern : 33(100% color Bar), the following screen is
displayed.
* It should be checked because the above pattern may be
different according to the model and the pattern of the used
equipment.
different according to the model and the pattern of the used
equipment.
2) Press the ADJ KEY of the adjusting R/C to enter into
‘EZ-ADJUST’ Select ‘4. Adjust AV_NTSC’ and press the
right arrow key (
right arrow key (
G
) to enter into the adjustment mode.
3) When the automatic adjustment is completed, the
message ‘AV-NTSC Configuration Success’ is
displayed. If the adjustment is failed, the message ‘AV-
NTSC Configuration Fail’ is displayed.
displayed. If the adjustment is failed, the message ‘AV-
NTSC Configuration Fail’ is displayed.
<Fig.4> Model : 202(PAL), Pattern : 33(100% Color Bar)
<Fig.5> Model : 201(NTSC), Pattern : 33(100% Color Bar)
- 8 -
7. Adjustment of White Balance
7-1. Required Equipment
1) Color Analyzer : CA-100(CH 10)
2) When adjusting the PLASMA color temperature, the No.
2) When adjusting the PLASMA color temperature, the No.
10 channel with the matrix compensated (White, Red,
Green and Blue compensated) should be used for the
CS-1000 as Color analyzer (CA-100), which should be
adjusted based on the white balance adjustment
coordinate as described below.
Green and Blue compensated) should be used for the
CS-1000 as Color analyzer (CA-100), which should be
adjusted based on the white balance adjustment
coordinate as described below.
2) Automatic adjuster (necessary for the automatic
adjustment, possible to communicate via the RS-232C)
3) Video Signal Generator MSPG-925F 720p,
216Gray(Model : 217, Pattern : 78)
7-2 Measuring device connection diagram
(for automatic adjustment)
7-3 White Balance adjustment method
Basically it uses the internal pattern but when internal pattern
is not possible, you can select HDMI input for adjustment.
Through the option at the most bottom part of the Ez Adjust
Menu 7.White Balance menu, you can select NONE, INNER
and HDMI, and the default is set to INNER. When the
adjustment cannot be done with the internal pattern, you can
select HDMI input for adjustment.
is not possible, you can select HDMI input for adjustment.
Through the option at the most bottom part of the Ez Adjust
Menu 7.White Balance menu, you can select NONE, INNER
and HDMI, and the default is set to INNER. When the
adjustment cannot be done with the internal pattern, you can
select HDMI input for adjustment.
For manual adjustment, press the ADJ KEY of the adjustment
R/C to enter Ez Adjust 7.White-Balance, and the pattern is
automatically displayed. (When you set the Option to INNER,
the default is always set to INNER)
R/C to enter Ez Adjust 7.White-Balance, and the pattern is
automatically displayed. (When you set the Option to INNER,
the default is always set to INNER)
1) Connect the set according to the internal pattern or HDMI
input in accordance with 7-3 measuring device connection
diagram.
diagram.
2) Set the Baud Rate of RS-232C to 115200. It is set to
115200 as default.
3) Connect the RS-232C Cable to the set.
4) Connect the HDMI Cable to the set. (Limited to the set with
4) Connect the HDMI Cable to the set. (Limited to the set with
HDMI option)
5) Select and adjust the model applicable to PB75A chassis
from the adjuster.
Caution) For automatic adjustment, RS-232C Command and
Chassis are commonly applied
Caution) Adjustment map
* White Balance adjustment (For automatic adjustment)
- Execute Power Only Key of the adjustment R/C to execute
automatic adjustment. Set the Baud Rate to 115200.
- Always start adjustment with “wb 00 00” and end
adjustment with “wb 00 ff”
- Adjust the offset if necessary.
adjustment with “wb 00 ff”
- Adjust the offset if necessary.
Color Analyer
RS-232C
Full White Pattern
(Inner pattern)
(Inner pattern)
<Fig. 6> Connection diagram for internal pattern
<Fig. 7> Connection diagram for HDMI input
216Gray White Pattern
(HDMI Pattern)
(HDMI Pattern)
Color Analyer
MSPG-925FS
MSPG-925FS
Video Signal Generator
Video Signal Generator
ideo Signal Generator
Model : 217
Model : 217
Pattern : 78
Pattern : 78
Pattern : 78
RS-232C
RS-232C
Baud Rate : 1
Baud Rate : 1
Baud Rate : 115200
15200
Remark
RS-232C Command
[CMD ID DATA]
wb
wb
wb
wb
wb
wb
00
00
00
00
00
00
00
10
1f
20
2f
ff
Start white balance adjustment
End Gain adjustment
End Offset adjustment
R Gain
G Gain
B Gain
R Cut
G Cut
B Cut
jg
jh
ji
Cool
ja
jb
jc
Mid
RS-232C COMMAND
[CMD ID DATA]
CENTER
(DEFAULT)
jd
je
jf
00
00
00
192
192
192
127
127
127
Warm
Min
Max
192
192
192
64
64
64
Cool
192
192
192
64
64
64
Mid
192
192
192
64
64
64
Warm
- 9 -
7-4. Adjustment of White Balance
(For manual adjustment)
- Required Equipment : When adjusting the PLASMA color
temperature, the No. 10 channel with the matrix
compensated (White, Red, Green and Blue
compensated) should be used for the CS-1000 as Color
analyzer (CA-100), which should be adjusted based on
the white balance adjustment coordinate as described
below.
compensated (White, Red, Green and Blue
compensated) should be used for the CS-1000 as Color
analyzer (CA-100), which should be adjusted based on
the white balance adjustment coordinate as described
below.
(1) Enter to ‘EZ-ADJUST’ by pressing ADJ key of R/C.
(2) HEAT RUN at least 30 minutes by pressing the ‘11. TEST
(2) HEAT RUN at least 30 minutes by pressing the ‘11. TEST
Pattern’ on the Service Remote Control and adjust.
(3) Set CA-100 in Zero Calibration, when adjust PDP module
make it contacting completely in the surface.
(4) Select ‘6. White-Balance’ of ‘Ez - Adjust’ by pressing the
ADJ KEY on the Service R/C. Then enter adjustment mode
by pressing the Right KEY (G). This time white pattern is
displayed. (When press Gkey, the screen enters to Full
White internal pattern.)
by pressing the Right KEY (G). This time white pattern is
displayed. (When press Gkey, the screen enters to Full
White internal pattern.)
(5) The adjustment completes in three color temperatures as
Cool, Medium, and Warm.
(6) When R GAIN is fixed at 192:
keep G GAIN and B GAIN less than 192 and find proper
values for adjustment.
values for adjustment.
When G GAIN is fixed at 192:
keep R GAIN and B GAIN less than 192 and find proper
values for adjustment.
values for adjustment.
When B GAIN is fixed at 192:
keep R GAIN and G GAIN less than 192 and find proper
values for adjustment.
values for adjustment.
(7) Adjust using Volume +/- KEY.
(8) When the adjustment is completed, press the OK (
(8) When the adjustment is completed, press the OK (
A
KEY)
button to move to the Ez –Adjust screen. Press the ADJ
KEY to exit the adjustment mode.
KEY to exit the adjustment mode.
[Ref.] White Balance Adjustment Pixel and Color Temperature
(1) Standard white balance standard white balance coordinate
when using CS-1000 device:
(2) Directed color coordinate when using CA-100 CH 10
Brightness: Full white 216gray
(3) Directed color coordinate when using CA-210 CH 10
8. Check the adjustment of the plant
shipping mode
Color temperature Color analyzer
Color coordinate
X
Y
COOL
CA-100
0.276±0.002
0.283±0.002
MEDIUM
CA-100
0.285±0.002
0.293±0.002
WARM
CA-100
0.313±0.002
0.329±0.002
Color temperature Color analyzer
Color coordinate
X
Y
COOL
CA-210
0.276±0.002
0.283±0.002
MEDIUM
CA-210
0.285±0.002
0.293±0.002
WARM
CA-210
0.313±0.002
0.329±0.002
Color temperature Measuring instrument
Color coordinate
X
Y
COOL
11000K, ∆uv=0.000
0.276
0.283
MEDIUM
9300K, ∆uv=0.000
0.285
0.293
WARM
6500K, ∆uv=0.000
0.313
0.329
1
2
3
4
5
6
7
8
9
10
Digital
30
Off
16:9
1
Dynamic
Cool
Off
Auto
Standard
Off
0
On
On
--
Off
Off
Off
16:9
Off
Normal
Off
C0, C5, C6, S11,
C20, C35, C52, C68
C43
Item
Condition
No
Remark
Input Mode
Volume Level
Mute
Aspect Ratio
SET ID
Picture PSM
Color Temp.
Advanced
Cinema
Black level
Sound
SSM
AVL
Balance
TV Speaker
Time
Auto Clock
Manual Clock
Off Timer / On Timer
Sleep Timer / Auto Off
Option
Sub title
Child Lock
ARC
Demo
ISM Method
Low Power
Channel Memory Analog
Digital
Click on the first or last page to see other 42PC5D-AB (CHASSIS:PB73B) service manuals if exist.