DOWNLOAD LG 42PC1D-UB / 42PC1DA-UB (CHASSIS:PA-61B) Service Manual ↓ Size: 27.82 MB | Pages: 46 in PDF or view online for FREE

- 6 -

REMOTE CONTROL KEY FUNCTIONS

When using the remote control, aim it at the remote control sensor on the TV.

APM   

CC

AUTO DEMO M/C EJECT

MODE

DAY+/DAY-

MENU

INFO

TV GUIDE 

THUMBSTICK

(Up/Down/Left

Right/ENTER)

EXIT

SAP

CC

RATIO

VOLUME UP

/DOWN

MUTE

FAV

CHANNEL

UP/DOWN

PAGE UP/

PAGE DOWN

— (DASH)

FLASHBK

Select the remote operating mode: TV, DVD, VCR,
AUDIO, CABLE or STB. 

Control video cassette recorders or DVD players.

Move the Listings Grid forward or backward in 24
hour increments.

Displays the main menu. Enters or exits a Panel
Menu in the TV Guide On Screen system.

Display information at the top of the screen. 

Displays the TV Guide On Screen system.

Navigate the on-screen menus and adjust the sys-
tem settings to your preference.

Clear all on-screen displays and return to TV view-
ing from any menu.

Analog mode: Selects MTS sound(Mono, Stereo, and a SAP)

DTV mode: Change the audio language.

Select a closed caption.
(*In DTV/CADTV mode

Change the aspect ratio.

Increase/decrease the sound level.

Switch the sound on or off.

Scroll through the programmed Favorite channels.

Select available channels.

Move from one full set of screen information to the
next one.

Used to enter a program number for multiple pro-
gram channels such as 2-1, 2-2, etc.

Tune to the last channel viewed.

VCR/DVD 

control buttons

NUMBER but-

- 7 -

Inside the Sliding Cover

POWER

TV INPUT

INPUT

Turns your TV or any other
programmed equipment on or
off, depending on the mode.

In AV 1-2, Component 1-2,
RGB-DTV (or RGB-PC),
HDMI1/DVI, and HDMI2 input
sources, screen returns to the
last TV channel.

External input modes rotate in
regular sequence: Antenna,
Cable, AV1-2, Component 1-
2, RGB-DTV (or RGB-PC),
HDMI1/DVI and HDMI2 (AV 1-
2, Component 1-2, RGB-DTV
(or RGB-PC), HDMI1/DVI,
and HDMI2 input sources are
linked automatically, only if
these are connected ).

TIMER

APM

ADJUST

Select the amount of time before your TV turns off auto-
matically. 

Compare the Daylight, Normal, Night Time and
User1(or2) on the screen. 

Adjust the screen position,size,and phase in PC mode. 

PIP

PIPCH-

/PIPCH+  

PIP INPUT

SWAP

EZ PIC

EZ SOUND

Switches the sub picture PIP, POP, Twin
picture or off mode. 

Changes the PIP channel. 

Select the connected input source for the
sub-picture. 

Exchange the main/sub images. 

Adjust the factory preset picture depend
on the viewing environment. 

Select the appropriate type of sound for
type of program. 

- 8 -

The specifications shown above may be changed without prior notice for quality improvement.

42PC1DA

(42PC1DA-UB)

MODELS

44.4 x 29.5 x 15.0 inches

1129.0 x 748.5 x 380.0 mm

44.4 x 27.4 x 4.1 inches

1129.0 x 695.0 x 103.7 mm

61.1 pounds / 27.7 kg

53.4 pounds / 24.2 kg

AC100-240V ~ 50/60Hz

NTSC-M, ATSC, 64 & 256 QAM

VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135

75 ohm

32 ~ 104°F (0 ~ 40°C)

Less than 80%

-4 ~ 140°F (-20 ~ 60°C)

0 ~ 85%

Dimensions

(Width x Height x Depth)

Weight

Power requirement

Television System

Program Coverage

External Antenna

Impedance

Environment condition

including stand

excluding stand

including stand

excluding stand

Operating Temperature

Operating Humidity

Storage Temperature

Storage Humidity

These instructions are applied to all of the PDP TV, PA61B.

(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation
transformer will help protect test equipment.

(2) Adjustments must be done in the correct order.
(3) The adjustments must be performed in the circumstance of

25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.

(4) The input voltage of the receiver be must kept 110V, 60Hz

when adjusting.

(5) The receiver must be operational for about 15 minutes

prior to the adjustments.  

O

Preliminary action is applied to the test for afterimage

discharge detection, and 100% FULL WHITE PATTERN
must be operated automatically.

O

Test for afterimage discharge detection

1) After pressing Power Only key(only operating by

pressing Power Only key), Full Test Pattern(2 min
30sec) --> Full Black Pattern(30sec) --> After this state,
Full White Pattern is displayed.
(but you must preset the program for Full White State
when you press the Main Power Off/On) 

2) Pattern Mode is deselected by pressing CH +/-, Exit Key.

[

Set is activated HEAT-RUN without signal generator in this

mode.

(1) Test Equipment: PC, Jig for download
(2) Connect the power of VSC B/D.
(3) Execute download program(iMPACK) of PC.
(4) After executing the hot key on the Programmer, click icon
(5) End after confirming

(1) As shown below, connect the MPLAB ICD2 equipment, PC

and Digital Connector.

(2) Turn on the MPLAB ICD2 POWER Supply.
(3) After turn on the PC and MONITOR, select the ‘MPLAB

IDE’ from the screen.

(1) When the program is executed, select the MPLAB ICD2

from Programmer -> Select Programmer . 

- 9 -

+13V

<Digital Board>

Connect the MPLAB ICD2 and connector of Digital Board

Connect the RS-232 or USB Cable

GND
Data

PC

VSC

B/D

Connection Diagram of EPLD Download

Test Pattern 2min 30sec

Test Pattern 30sec

If you turn on a still screen more than 20 minutes (Especially
Digital pattern(13 CH), Cross Hatch Pattern), an afterimage
may occur in the black level part of the screen.