LG 42LT760H-SA (CHASSIS:LJ3AZ) Service Manual ▷ View online
- 9 -
4.2.5. Download
4.2.6. Inspection
- In INSTART menu, check these keys.
4.3. LAN Inspection
4.3.1. Equipment & Condition
▪ Each other connection to LAN Port of IP Hub and Jig
4.3.2. LAN inspection solution
▪ LAN Port connection with PCB
▪ Network setting at MENU Mode of TV (Installer Menu -> 119
-> 253 -> Menu)
▪ setting automatic IP
▪ Setting state confirmation
- If automatic setting is finished, you confirm IP and MAC
Address.
4.4. LAN PORT INSPECTION(PING TEST)
4.4.1. Equipment setting
1) Play the LAN Port Test PROGRAM.
2) Input IP set up for an inspection to Test
Program.
*IP Number : 12.12.2.2.
*IP Number : 12.12.2.2.
4.4.2. LAN PORT inspection (PING TEST)
1) Play the LAN Port Test Program.
2) connect each other LAN Port Jack.
3) Play Test (F9) button and confirm OK Message.
4) remove LAN CABLE
- 10 -
4.5. Model name & Serial number Download
4.5.1. Model name & Serial number D/L
■ Press “Power on” key of service remocon.(Baud rate :
115200 bps)
■ Connect RS232 Signal Cable to RS-232 Jack.
■ Write Serial number by use RS-232.
■ Must check the serial number at Instart menu
4.5.2. Method & notice
A. Serial number D/L is using of scan equipment.
B. Setting of scan equipment operated by Manufacturing
Technology Group.
C. Serial number D/L must be conformed when it is produced
in production line, because serial number D/L is mandatory
by D-book 4.0
※
Manual Download (Model Name and Serial Number)
If the TV set is downloaded By OTA or Service man,
Sometimes model name or serial number is initialized.( Not
always)
There is impossible to download by bar code scan, so It need
Manual download.
a. Press the ‘instart’ key of ADJ remote controller.
b. Go to the menu ‘7.Model Number D/L’ like below photo.
c. Input the Factory model name(ex 32LT760H-SA) or Serial
number like photo
d. Check the model name Instart menu -> Factory name
displayed (ex 32LT760H-SA)
e. Check the Diagnostics (DTV country only) -> Buyer model
displayed (ex 32LT760H-SA)
4.6. WIFI MAC ADDRESS CHECK
4.6.1. Using RS232 Command
Command
Set ACK
Transmission
[A][l][][Set ID][][20][Cr] [O][K][x] or [N][G]
4.6.2. Check the menu on in-start
5. Manual Adjustment
5.1. ADC adjustment is not needed because
of OTP(Auto ADC adjustment)
5.2. EDID
(The Extended Display Identification Data)
/ DDC (Display Data Channel) download
5.2.1. Overview
It is a VESA regulation. A PC or a MNT will display an optimal
resolution through information sharing without any necessity of
user input. It is a realization of “Plug and Play”
5.2.2. Equipment
▪ Since embedded EDID data is used, EDID download JIG,
HDMI cable and D-sub cable are not need.
- 11 -
5.2.3. EDID DATA
▪ Since embedded EDID data is used, EDID download JIG,
HDMI ca
▪ 2D EDID (FHD MODEL : 37/42LT760H-SA)
▪Reference
- HDMI1 ~ HDMI3 / RGB
- In the data of EDID, bellows may be different by S/W or Input
mode.
ⓐ
Product ID
HEX
EDID Table
DDC Function
0001
0100
Analog
0001
0100
Digital
ⓑ
Serial No: Controlled on production line.
ⓒ
Month, Year: Controlled on production line:
ex) Monthly : ‘01’ -> ‘01’
Year : ‘2012’ -> ‘16’
ⓓ
Model Name(Hex): LGTV
Chassis
MODEL NAME(HEX)
LJ3AZ
00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20
ⓔ
Checksum(LG TV): Changeable by total EDID data.
ⓔ
1
ⓔ
2
ⓔ
3
HDMI1
43
15
X
HDMI2
43
5
X
HDMI3
43
F5
X
RGB
X
X
5C
ⓕ
Vendor Specific(HDMI)
INPUT
MODEL NAME(HEX)
HDMI1
67 03 0C 00 10 00 80 2D
HDMI2
67 03 0C 00 20 00 80 2D
HDMI3
67 03 0C 00 30 00 80 2D
▪ 2D EDID (HD MODEL : 32LT760H-SA)
*RGB_EDID DATA
▪Reference
- HDMI1 ~ HDMI3 / RGB
- In the data of EDID, bellows may be different by S/W or Input
mode.
ⓐ
Product ID
HEX
EDID Table
DDC Function
0001
0100
Analog
0001
0100
Digital
ⓑ
Serial No: Controlled on production line.
ⓒ
Month, Year: Controlled on production line:
ex) Monthly : ‘01’ -> ‘01’
Year : ‘2012’ -> ‘16’
ⓓ
Model Name(Hex): LGTV
Chassis
MODEL NAME(HEX)
LJ3AZ
00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20
ⓔ
Checksum(LG TV): Changeable by total EDID data.
ⓔ
1
ⓔ
2
ⓔ
3
HDMI1
78
D5
X
HDMI2
78
C5
X
HDMI3
78
B5
X
RGB
X
X
91
ⓕ
Vendor Specific(HDMI)
INPUT
MODEL NAME(HEX)
HDMI1
65 03 0C 00 10 00 01 1D
HDMI2
65 03 0C 00 20 00 01 1D
HDMI3
65 03 0C 00 30 00 01 1D
a
c
e1
b
d
e2
f
- 12 -
5.3. White Balance Adjustment
5.3.1. Overview
5.3.1.1. W/B adj. Objective & How-it-works
(1) Objective: To reduce each Panel’s W/B deviation
(2) How-it-works: When R/G/B gain in the OSD is at 192, it
means the panel is at its Full Dynamic Range. In order to
prevent saturation of Full Dynamic range and data, one of
R/G/B is fixed at 192, and the other two is lowered to find
the desired value.
(3) Adj. condition: normal temperature
- Surrounding Temperature: 25±5 °C
- Warm-up time: About 5 Min
- Surrounding Humidity: 20% ~ 80%
- Before White balance adjustment, Keep power on status,
don’t power off
5.3.2. Equipment
(1) Color Analyzer: CA-210 (LED Module : CH 14)
(2) Adj. Computer (During auto adj., RS-232C protocol is
needed)
(3) Adjust Remocon
(4) Video Signal Generator MSPG-925F 720p/204-
Gray(Model:217, Pattern:49)
→ Only when internal pattern is not available
※
Color Analyzer Matrix should be calibrated using CS-1000
5.3.3. Equipment connection
5.3.4. Adjustment Command (Protocol)
<Command Format>
START 6E A 50 A LEN A 03 A CMD A 00 A VAL A CS A
STOP
- LEN: Number of Data Byte to be sent
- CMD: Command
- VAL: FOS Data value
- CS: Checksum of sent data
- A: Acknowledge
Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX]
▪ RS-232C Command used during auto-adj
RS-232C COMMAND
Explanation
CMD
DATA
ID
wb
00
00
Begin White Balance adj.
wb
00
10
Gain adj.(internal white pattern)
wb
00
1f
Gain adj. completed
wb
00
20
Offset adj.(internal white pattern)
wb
00
2f
Offset adj. completed
Wb
00
ff
End White Balance adj.
(internal pattern disappears )
Ex) wb 00 00 -> Begin white balance auto-adj.
wb 00 10 -> Gain adj.
ja 00 ff -> Adj. data
jb 00 c0
...
...
wb 00 1f -> Gain adj. complete
*(wb 00 20(start), wb 00 2f(endc)) -> Off-set adj.
wb 00 ff ->End white balance auto adj.
▪ Adj. Map
Adj. item Command
(lower caseASCII)
Data Range
(Hex.)
CMD1
CMD2
MIN
MAX
Cool
R Gain
j
g
00
C0
G Gain
j
h
00
C0
B Gain
j
i
00
C0
Medium
R Gain
j
a
00
C0
G Gain
j
b
00
C0
B Gain
j
c
00
C0
Warm
R Gain
j
d
00
C0
G Gain
j
e
00
C0
B Gain
j
f
00
C0
5.3.5. Adjustment method
5.3.5.1 Auto WB calibration
(1) Set TV in ADJ mode using P-ONLY key (or POWER ON
key)
(2) Place optical probe on the center of the display
- It need to check probe condition of zero calibration before
adjustment.
(3) Connect RS-232C Cable
(4) Select mode in ADJ Program and begin a adjustment.
(5) When WB adjustment is completed with OK message,
check adjustment status of pre-set mode (Cool, Medium,
Warm)
(6) Remove probe and RS-232C cable.
▪ W/B Adj. must begin as start command “wb 00 00” , and
finish as end command “wb 00 ff”, and Adj. offset if need
Color Analyzer
Computer
Pattern Generator
※
Signal Source
Probe
RS-232C
RS-232C
RS-232C
※
If TV internal pattern is used, not needed
Click on the first or last page to see other 42LT760H-SA (CHASSIS:LJ3AZ) service manuals if exist.