DOWNLOAD LG 42LN549C / 42LP360H (CHASSIS:LB3AC) Service Manual ↓ Size: 6.34 MB | Pages: 34 in PDF or view online for FREE

Model
42LN549C 42LP360H (CHASSIS:LB3AC)
Pages
34
Size
6.34 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / LCD
File
42ln549c-42lp360h-chassis-lb3ac.pdf
Date

LG 42LN549C / 42LP360H (CHASSIS:LB3AC) Service Manual ▷ View online

- 11 -
*  Connecting picture of the measuring instrument
(On Automatic control)
Inside PATTERN is used when W/B is controlled. Connect to 
auto  controller  or  push Adjustment  R/C  POWER  ON  → 
Enter the mode of White-Balance, the pattern will come out.
* Auto-control interface and directions
(1)  Adjust in the place where the influx of light like floodlight 
around is blocked. (illumination is less than 10 lux).
(2)  Adhere closely the Color analyzer(CA210) to the module 
less than 10 cm distance, keep it with the surface of the 
Module and Color analyzer's prove vertically.(80° ~ 100°).
(3) Aging time
-  After aging start, keep the power on (no suspension of 
power supply) and heat-run over 5 minutes.
-  Using 'no signal' or 'POWER ONLY' or the others, check 
the back light on.
▪ Auto adjustment Map(using RS-232C to USB cable)
RS-232C COMMAND
[CMD  ID  DATA]
  Wb 
00  00 
White Balance Start
  Wb 
00  ff 
White Balance End
<Caution>
Color Temperature : COOL, Medium, Warm. 
One of R Gain/G Gain/ B Gain should be kept on 0xC0, and 
adjust  other  two  lower  than  C0.(When  R/G/B  Gain  are  all 
C0, it is the FULL Dynamic Range of Module)
* Manual W/B process using adjust Remote control.
▪ After enter Service Mode by pushing "ADJ" key,
▪  Enter  White  Balance  by  pushing  "►"  key  at  "9.  White 
Balance". 
■  For manual adjustment, it is also possible by the following 
sequence.
(1)  Set  TV  in Adj.  mode  using  “P-ONLY”  key  on  remote 
controller  and  then  operate  heat  run  longer  than  15 
minutes.(If not executed this step, the condition for W/B 
may be different.)
(2) Push “Exit” key.
(3)  Enter White Balance mode by pushing the ADJ key and 
select “9. White Balance” When KEY (►) is pressed, 206 
Gray internal pattern will be displayed. 
(4)  Zero Calibrate the probe of Color Analyzer, then place it 
on the center of LCD module within 10cm of the surface
(5)  Select each items (Red/Green/Blue Gain) using ▲/▼(CH 
+/-) key on R/C..
(6) Adjust R/ G/ B Gain using ◄/►(VOL +/-) key on R/C.
(7) Adjust three modes all (Cool / Medium / Warm) 
- For All model w/o LS345
Fix the one of R/G/B gain and change the others
- For G-FIX model (TBD)
Cool Mode
1)  Fix the one of R/G/B gain to 192 (default data) and 
decrease  the  others.(If  G  gain  is  adjusted  over  172 
and R and B gain less than 192 , Adjust is O.K.)
2)  If G gain is less than 172, Increase G gain by up to 
172,  and  then  increase  R  gain  and  G  gain  same 
amount of increasing G gain. 
3)  If R gain or B gain is over 255, readjust G gain less 
than 172, Conform to R gain is 255 or B gain is 255 
     Medium / Warm Mode - Fix the one of R/G/B gain to 
192 (default data) and decrease the others.
(8)  When  adjustment  is  completed,  exit  adjustment  mode 
using EXIT key on R/C.
Full White Pattern
CA-210
COLOR
ANALYZER
TYPE : CA-210
RS-232C Communication
RS-232C COMMAND
[CMD ID DATA]
MIN
CENTER
(DEFAULT)
MAX
Cool
Mid
Warm
Cool Mid Warm
R Gain jg
Ja
jd
00
172
192 192
192
G Gain jh
Jb
je
00
172
192 192
192
B Gain ji
Jc
jf
00
192
192 172
192
R Cut
64
64
64
128
G Cut
64
64
64
128
B Cut
64
64
64
128
EZ ADJUST
0. Tool Option1
1. Tool Option2
2. Tool Option3
3. Tool Option4
4. Tool Option5
5. Tool Option6
6. Commercial Tool Option
7. Country Group
8. Area Option
9. ADC Calibration
10. White Balance   
11. 10 Point WB
12. Test Pattern
13 EDID D/L
14. Sub B/C
15. Ext. Input Adjust
16. SPK Lipsync Adjust
17. SPDIF Lipsync Adjust
Whit Balance
Color Temp. 
 
R-Gain
G-Gain
B-Gain
R-Cut
G-Cut
B-Cut
Test-Pattern
Backlight
Reset 
      To Set
Cool
172
172
192
64
64
64
ON
100
- 12 -
* CASE Cool
First adjust the coordinate far away from the target value(x, y).
 x, y > target
i) Decrease the R, G. 
 x, y < target
i) First decrease the B gain, 
ii) Decrease the one of the others.
 x > target, y < target
i)  First  decrease  B,  so  make  y  a  little  more  than  the 
target.
ii) Adjust x value by decreasing the R
 x < target, y > target
i)  First  decrease  B,  so  make  x  a  little  more  than  the 
target.
ii) Adjust x value by decreasing the G
*  After You finish all adjustments, Press “In-start” button and 
compare Tool option and Area option value with its BOM, if 
it is correctly same then unplug the AC cable.
   If it is not same, then correct it same with BOM and unplug 
AC cable.
  For correct it to the model’s module from factory JIG model.
*  Push  The  “IN  STOP  KEY”  after  completing  the  function 
inspection.
4.2. DDC EDID Write (RGB 128Byte )
■ Connect D-sub Signal Cable to D-Sub Jack.
■  Write  EDID  DATA  to  EEPROM(24C02)  by  using  DDC2B 
protocol.
■ Check whether written EDID data is correct or not.
*  For Service main Assembly, EDID have to be downloaded to 
Insert Process in advance.
4.3. DDC EDID Write (HDMI 256Byte)
■ Connect HDMI Signal Cable to HDMI Jack.
■  Write  EDID  DATA  to  EEPROM(24C02)  by  using  DDC2B 
protocol.
■ Check whether written EDID data is correct or not.
*  For Service main Assembly, EDID have to be downloaded to 
Insert Process in advance.
4.4. EDID data
(1) All Data : HEXA Value
(2) Changeable Data :
    *: Serial No : Controlled / Data:01
    **: Month : Controlled / Data:00
    ***: Year : Controlled
    ****: Check sum
4.4.1. Auto Download
■ After enter Service Mode by pushing “ADJ” key,
■Enter EDID D/L mode.
■Enter “START” by pushing “OK” key. 
* Caution :  Never  connect  HDMI  &  D-sub  Cable  when  EDID 
downloaded. 
* EDID data and Model option download (RS232)
4.4.2. Manual Download
<Caution>
(1) Use the proper signal cable for EDID Download
* For HDMI EDID(DVI-D to HDMI or HDMI to HDMI Cable)
- Analog EDID : Pin3 exists
- Digital EDID : Pin3 exists
(2) Never connect HDMI & D-sub Cable at the same time.
(3) Use the proper cables below for EDID Writing.
(4)  Download  HDMI1,  HDMI2  separately  because  HDMI1  is 
different from HDMI2.
EZ ADJUST
0. Tool Option1
1. Tool Option2
2. Tool Option3
3. Tool Option4
4. Tool Option5
5. Tool Option Commercial
6. Country Group
7. Area Option
8. ADC Calibration
9. White Balance
10. 10 Point WB
11. Test Pattern
12. EDID D/L 
 
13. Sub B/C
14. Ext. Input Adjust
EDID
  HDMI1 
NG
  HDMI2 
NG
  HDMI3 
NG
  RGB 
NG
Start
Reset
EDID
  HDMI1 
OK
  HDMI2 
OK
  HDMI3 
OK
  RGB 
OK
Start
Reset
NO
Item
CMD 1 CMD 2 Data 0
Enter download
MODE
Download
‘Mode In’
A
A
0
0 When transfer the ‘Mode 
In’, Carry the command.
EDID data and
Model option
download
Download
A
E
00 10
Automatically download
(The use of a internal 
data)
For Analog
For HDMI EDID
D-sub to D-sub
DVI-D to HDMI or HDMI to HDMI
No.
Item
Condition
Hex Data
1
Manufacturer ID
GSM
1E6D
2
Version
Digital : 1
01
3
Revision
Digital : 3
03
- 13 -
(1) FHD RGB EDID data
(2) FHD HDMI EDID data
(3) Detail EDID Options are below
a. Product ID
b. Serial No: Controlled on production line.
c. Month, Year: Controlled on production line:
ex) Week : '01' -> '01'
Year : '2012' -> '16' fix
d. Model Name(Hex):
cf) TV set’s model name in EDID data is below. 
e. Checksum: Changeable by total EDID data.
f. Vendor Specific(HDMI)
4.5. Model name & Serial number D/L
▪ Press "Power on" key of service remote control.
(Baud rate : 115200 bps)
▪ Connect RS232 Signal Cable to RS-232 Jack.
▪ Write Serial number by use RS-232.
▪  Must check the serial number at the Diagnostics of SET UP 
menu. (Refer to below)
(1) Signal Table
CMD : A0h
LENGTH : 85~94h (1~16 bytes)
ADH : EEPROM Sub Address high (00~1F)
ADL : EEPROM Sub Address low (00~FF)
Data : Write data
CS : CMD + LENGTH + ADH + ADL + Data_1 +...+ Data_n
Delay : 20ms
(2) Comand Set
* Description
FOS Default write : <7mode data> write
Vtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 
0, Phase
Data write :  Model  Name  and  Serial  Number  write  in 
EEPROM,.
(3) Method & notice
1) Serial number D/L is using of scan equipment.
2)  Setting  of  scan  equipment  operated  by  Manufacturing 
Technology Group.
3)  Serial  number  D/L  must  be  conformed  when  it  is 
produced in production line, because serial number D/L 
is mandatory by D-book 4.0.
0
1
2
3
4
5
6
7
8
9
A B C D E
F
00 00 FF FF FF FF FF FF 00 1E 6D
a
b
10
c
01 03 80 10 09 78 0A EE 91 A3 54 4C 99 26
20 0F 50 54 A1 08 00 71 4F 81 80 01 01 01 01 01 01
30 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C
40 45 00 A0 5A 00 00 00 1E 1B 21 50 A0 51 00 1E 30
50 48 88 35 00 A0 5A 00 00 00 1C 00 00 00 FD 00 3A
60 3E 1E 53 10 00 0A 20 20 20 20 20 20
d
70
d
01 e
80 02 03 26 F1 4E 10 1F 84 13 05 14 03 02 12 20 21
90 22 15 01 26 15 07 50 09 57 07
f
A0
f
E3 05 03 01 01 1D 80 18 71 1C 16 20 58 2C
B0 25 00 A0 5A 00 00 00 9E 01 1D 00 72 51 D0 1E 20
C0 6E 28 55 00 A0 5A 00 00 00 1E 02 3A 80 18 71 38
D0 2D 40 58 2C 45 00 A0 5A 00 00 00 1E 01 1D 00 BC
E0 52 D0 1E 20 B8 28 55 40 A0 5A 00 00 00 1E 00 00
F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e
MODEL NAME
HEX
EDID Table
DDC Function
HD/FHD Model
0001
01 00
Analog/Digital
Model name
MODEL NAME(HEX)
LG TV
00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20  (LG TV)
EDID C/S data
FHD
HDMI
RGB
Check sum
(Hex)
Block 0
43
5C
Block 1
25 (HDMI1)
-
15 (HDMI2)
5 (HDMI3)
Input
Model name(HEX)
HDMI1
67030C001000B82D
HDMI2
67030C002000B82D
HDMI3
67030C003000B82D
CMD
LENGTH
ADH
ADL
DATA_1
. . .
Data_n
CS
DELAY
Adjust mode
CMD(hex)
LENGTH(hex)
Description
EEPROM WRITE
A0h
84h+n
n-bytes Write (n = 1~16)
0
1
2
3
4
5
6
7
8
9
A B C D E
F
00 00 FF FF FF FF FF FF 00 1E 6D
a
b
10
c
01 03 68 10 09 78 0A EE 91 A3 54 4C 99 26
20 0F 50 54 A1 08 00 81 80 61 40 45 40 31 40 01 01
30 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C
40 45 00 A0 5A 00 00 00 1E 01 1D 00 72 51 D0 1E 20
50 6E 28 55 00 A0 5A 00 00 00 1E 00 00 00 FD 00 3A
60 3E 1E 53 10 00 0A 20 20 20 20 20 20
d
70
d
00 e
- 14 -
* Manual Download(Model Name and Serial Number)
If  the  TV  set  is  downloaded  by  OTA  or  Service  man, 
sometimes  model  name  or  serial  number  is  initialized.(Not 
always)
There  is  impossible  to  download  by  bar  code  scan,  so  It 
need Manual download.
1) Press the "Instart" key of Adjustment remote control.
2) Go to the menu "6.Model Number D/L" like below photo.
3)  Input the Factory model name(ex 32LV2510-TB) or Serial 
number like photo.
4)  Check  the  model  name  Instart  menu.  →  Factory  name 
displayed. (ex 32LV2510-TB)
5)  Check the Product/Service Info.(Menu Key → Red Key → 
Select  Product/Service  Info.)  →  Buyer  model  displayed 
(ex 32LV2510-TB)
4.5. Outgoing condition Configuration
■  When  pressing  IN-STOP  key  by  Service  remote  control, 
Red  LED  are  blinked  alternatively. And  then  automatically 
turn off. (Must not AC power OFF during blinking)
5. Check Commercial features
5.1. External SPK Out and Volume control
(1)  Connect external speaker to speaker out port with phone 
jack on TV side as below.
(2)  Check  the  Max.  speaker  output  is  1W  or  not.  Sine  wave 
with 1KHz will be displayed.
5.2. IR Out
5.2.1. In using Commercial Check Jig
(1) Check the LED for IR-Out inspection.
* Please refer to the criteria of Judgement.
5.2.2. In using Mini check Jig
(1)  Connect  JIG  for  inspection  to  RS-232C  port  on  TV  as 
below. 
(2) Check the LED for IR-Out inspection.
* Please refer to the criteria of Judgement.
Page of 34
Display

Click on the first or last page to see other 42LN549C / 42LP360H (CHASSIS:LB3AC) service manuals if exist.