LG 42LM6210 (CHASSIS:LJ22E) Service Manual ▷ View online
- 13 -
5.2.9. Component 3D Input (3D supported mode manually)
No
Resolution
H-freq(kHz)
V-freq.(Hz)
Pixel clock(MHz)
3D input proposed mode
Proposed
1
1280*720
37.5
50
74.25
2D to 3D,
Side by Side(half),
Top & Bottom
HDTV 720P
2
1280*720
45.00
60.00
74.25
2D to 3D,
Side by Side(half),
Top & Bottom
HDTV 720P
3
1280*720
44.96
59.94
74.176
2D to 3D,
Side by Side(half)
Top & Bottom
HDTV 720P
4
1920*1080
33.75
60.00
74.25
2D to 3D,
Side by Side(half)
Top & Bottom
HDTV 1080I
5
1920*1080
33.72
59.94
74.176
2D to 3D,
Side by Side(half)
Top & Bottom
HDTV 1080I
6
1920*1080
28.12
50
74.25
2D to 3D,
Side by Side(half)
Top & Bottom
HDTV 1080I
7
1920*1080
67.500
60
148.50
2D to 3D,
Side by Side(half)
Top & Bottom
HDTV 1080P
8
1920*1080
67.432
59.94
148.352
2D to 3D,
Side by Side(half)
Top & Bottom
HDTV 1080P
9
1920*1080
27.000
24.000
74.25
2D to 3D,
Side by Side(half)
Top & Bottom
HDTV 1080P
10
1920*1080
28.12
25
74.25
2D to 3D,
Side by Side(half)
Top & Bottom
HDTV 1080P
11
1920*1080
56.25
50
74.25
2D to 3D,
Side by Side(half)
Top & Bottom
HDTV 1080P
12
1920*1080
26.97
23.976
74.176
2D to 3D,
Side by Side(half)
Top & Bottom
HDTV 1080P
13
1920*1080
33.75
30.000
74.25
2D to 3D,
Side by Side(half)
Top & Bottom
HDTV 1080P
14
1920*1080
33.71
29.97
74.176
2D to 3D,
Side by Side(half)
Top & Bottom
HDTV 1080P
- 14 -
ADJUSTMENT INSTRUCTION
1. Application Range
This specification sheet is applied all of the LJ22E LCD TV
models, which produced in manufacture department or similar
LG TV factory.
2. Specification
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order. But it is
flexible when its factory local problem occurs.
(3) The adjustment must be performed in the circumstance of
25 ±5ºC of temperature and 65±10% of relative humidity if
there is no specific designation.
(4) The input voltage of the receiver must keep 100~220V,
50/60Hz.
(5) Before adjustment, execute Heat-Run for 5 minutes.
▪ After Receive 100% Full white pattern (06CH) then process
Heat-run
(or “8. Test pattern” condition of Ez-Adjust status)
▪ How to make set white pattern
1) Press Power ON button of Service Remocon
2) Press ADJ button of Service remocon. Select “8. Test
pattern” and, after select “White” using navigation button,
and then you can see 100% Full White pattern.
* In this status you can maintain Heat-Run useless any pattern
generator
* Notice : if you maintain one picture over 20 minutes
(Especially sharp distinction black with white pattern
-13Ch, or Cross hatch pattern – 09Ch) then it can
appear image stick near black level.
3. Adjustment items
3.1. PCB Assembly Adjustment
▪ MAC Address / ESN / Widevine Download
▪ Adjust 1080p Comp1/RGB (Except GP3 BCM MODEL using
ADC OTP)
▪ EDID (The Extended Display Identification Data)/DDC
(Display Data Channel) download
* If it is necessary, it can adjustment at Manufacture Line
You can see set adjustment status at “1. ADJUST CHECK”
of the “In-start menu”
3.2. Set Assembly Adjustment
▪ Color Temperature (White Balance) Adjustment
▪ Using RS-232C
▪ PING Test
▪ Selection Factory output option
4. PCB Assembly Adjustment
4.1. MAC Address, ESN Key and Widevine
Key download
4.1.1. Equipment & Condition
1) Play file: keydownload.exe
4.1.2. Communication Port connection
1) Key Write: Com 1,2,3,4 and 115200 (Baudrate)
2) Barcode: Com 1,2,3,4 and 9600 (Baudrate)
4.1.3. Download process
1) Select the download items.
2) Mode check: Online Only
3) Check the test process
- DETECT -> MAC_WRITE -> ESN_WRITE -> WIDEVINE_
WRITE
4) Play : START
5) Check of result: Ready, Test, OK or NG
4.1.4. Communication Port connection
1) Connect: PCBA Jig -> RS-232C Port == PC -> RS-232C
Port
4.1.5. Download
1) 11Y LCD TV + MAC + Widevine + ESN Key
4.1.6. Inspection
- In INSTART menu, check these keys.
- 15 -
4.2. LAN PORT INSPECTION(PING TEST)
4.1.1. Equipment setting
1) Play the LAN Port Test PROGRAM.
2) Input IP set up for an inspection to Test
Program.
*IP Number : 12.12.2.2.
*IP Number : 12.12.2.2.
4.2.2. LAN PORT inspection (PING TEST)
1) Play the LAN Port Test Program.
2) connect each other LAN Port Jack.
3) Play Test (F9) button and confirm OK Message.
4) remove LAN CABLE
4.3. Using RS-232C
- Adjust 3 items at 3.1 PCB assembly adjustments “adjustment
sequence” one after the order.
● Adjustment protocol
Order
Command
Set response
(1) Inter the Adjustment mode aa 00 00
a 00 OK00x
(2) Change the Source
xb 00 40
xb 00 60
b 00 OK40x (Adjust 480i Comp1 )
(Adjust 1080p Comp1)
b 00 OK60x (Adjust 1080p RGB)
(3) Start Adjustment
ad 00 10
(4) Return the Response
OKx ( Success condition )
NGx ( Failed condition )
(5) Read Adjustment data
( main)
ad 00 20
( main )
ad 00 30
(main : component1 480i, RGB 1080p)
000000000000000000000000007c007b-
006dx
(main : component1 1080p)
000000070000000000000000007c0083
0077x
(6) Confirm Adjustment
ad 00 99
NG 03 00x (Failed condition)
NG 03 01x (Failed condition)
NG 03 02x (Failed condition)
OK 03 03x (Success condition)
(7) End of Adjustment
ad 00 90
d 00 OK90x
See ADC Adjustment RS232C Protocol_Ver1.0
● Necessary items before Adjustment items
▪ Pattern Generator : (MSPG-925FA)
▪ Adjust 480i Comp1 (MSPG-925FA:model :209 , pattern :65) –
Comp1 Mode
▪ Adjust 1080p Comp1 (MSPG-925FA:model :225 , pattern
:65) – Comp1 Mode
▪ Adjust RGB (MSPG-925FA:model :225 , Pattern :65) – RGB-
PC Mode
If you want more information then see the below Adjustment
method (Factory Adjustment)
● Adjustment sequence
▪ aa 00 00: Enter the ADC Adjustment mode.
▪ xb 00 40: Change the mode to Component1 (No actions)
▪ ad 00 10: Adjust 480i Comp
▪ ad 00 10: Adjust 1080p Comp
▪ xb 00 60: Change to RGB-PC mode(No action)
▪ ad 00 10: Adjust 1080p RGB
▪ xb 00 90: Endo of Adjustmennt
- 16 -
5. Factory Adjustment
5.1. EDID (The Extended Display Identification
Data)/DDC (Display Data Channel) Download
● Summary
▪ It is established in VESA, for communication between PC
and Monitor without order from user for building user
condition. It helps to make easily use realize “Plug and Play”
function. For EDID data write, we use DDC2B protocol.
● Auto Download
▪ After enter Service Mode by pushing “ADJ” key
▪ Enter EDID D/L mode.
▪ Enter “START” by pushing “OK” key.
=> Caution : Never connect HDMI & D-sub Cable when the
user downloading . Use the proper cables below
for EDID Writing.
※
Edid data and Model option download (RS232)
NO
Item
CMD 1 CMD 2
Data 0
Enter
download
MODE
Download
‘Mode In’
A
E
0
0
When transfer the
‘Mode In’,
Carry the com-
mand.
Edid data
and
Model
option
download
Download
A
E
*Note1 *Note2 Automatically
download
(The use of a
internal Data)
Adjust
‘Mode Out’
A
E
9
0
Adjustment
Confirma-
tion
A
E
9
9
To check Download
on Assembly line.
Manual Download
● Write HDMI EDID data
▪ Using instruments
- Jig.(PC Serial to D-Sub connection) for PC, DDC adjustment.
- S/W for DDC recording (EDID data write and read)
- D-sub jack
- Additional HDMI cable connection Jig.
▪ Preparing and setting
- Set instruments and Jig. Like pic.5), then turn on PC and Jig
- Operate DDC write S/W (EDID write & read)
- It will operate in the DOS mode.
Pic.3) For write EDID data, setting Jig and another instruments.
* EDID data for Non 3DTV (LS5700-SB Series) (Model name =
LG TV)
- HDMI EDID table (0x1E : Physical Address)
- HDMI-1 EDID table (0x43, 0x15)
1) HDMI 1 Check sum : 0x43, 0X15 (CEA Block 0x1E :10)
2) HDMI 2 Check sum : 0x43, 0X05 (CEA Block 0x1E :20)
3) HDMI 3 Check sum : 0x43, 0XF5 (CEA Block 0x1E :30)
4) HDMI 4 Check sum : 0x43, 0XE5 (CEA Block 0x1E :40)
- Analog (RGB) EDID table
1) RGB CheckSum : 5C
PC
JIG
LCD TV SET
(or digital board)
(or digital board)
Click on the first or last page to see other 42LM6210 (CHASSIS:LJ22E) service manuals if exist.