DOWNLOAD LG 42LG30 (CHASSIS:LA85D) Service Manual ↓ Size: 5.74 MB | Pages: 39 in PDF or view online for FREE

- 13 -

(3) Adjustment Map

(Automatic Adjustment)

1) The adjustment condition should be set by the Power On

key.

2) Perform the zero calibration of the Color Analyzer and

place the probe close to the display center.

3) Connect the communication cable (RS-232C).
4) Select the desired model of the adjustment program and

perform the adjustment.

5) After the adjustment is ended (check the OK sign), check

the adjustment condition for each mode of the set.
(Warm, Medium, Cool)

6) Disconnect the probe and the communication cable to end

the adjustment.

* The adjustment should be started with "wb 00 00" and

ended with "wb 00 ff", and the offset should be adjusted
when necessary.

1) The adjustment condition should be set by the Power On

key.

2) Press the ADJ of the R/C to enter into 'EZ-ADJUST'.
3) Select '10.TEST PATTERN' with the CH +/- key and press

the Enter key for 30 minutes or longer to perform the heat
run.

4) Perform the zero calibration of the Color Analyzer and fix

the sensor with the 10cm or less distance at the center of
the LCD module surface when adjusting.

5) Press the ADJ of the R/C to select '7.White-Balance' of the

Ez-Adjust and press the right arrow key(

G

) to enter into the

adjustment mode. (As soon as you press '

G

', the screen is

entered into the full white inner pattern.)

6) Fix one of the R/G/B gains to 192 and decrease the

remaining two gains to adjust not to exceed 192.

7) The adjustment is done at three white balances of Cool,

Medium and Warm.

* The inner pattern is basically used, and if it is not possible,

the adjustment can be done by selecting the HDMI input.
NONE, INNER or HDMI can be selected by the bottom
option at the Ez Adjust Menu 7.White Balance menu and it is
set to INNER as default. If the adjustment cannot be done by
the inner pattern, select the HDMI to adjust.

1) Environment illuminance

Adjust it to 10 LUX or less at the place where the light
source such as lamp should be blocked at maximum.

2) Probe location

: Maintain the Color Analyzer (CA-210) close to the

module surface by 10cm or less and keep the probe of
the Color Analyzer perpendicular to the module
surface (80°~ 100°).

3) Aging time

- Keep the power on after the aging start (with no power

off) to perform the heat run for 15 minutes or longer.

- Make sure that the back light is turned on by using no

signal and the full white pattern or others.

(1) Brightness: Full white 216 Gray 
(2) Standard color coordinate and white balance when using

the CS-1000

(3) Standard color coordinate and white balance when using

the CA-210 (CH 10)

• Set write size to 64 bytes 
• Set delay time to 250ms 
• Connect D-sub Signal Cable to D-Sub Jack
• Input HDCP key with HDCP-key- in-program
• HDCP Key value is stored on EEPROM(AT24C512) which is

80~A1 addresses o 0xA0~0xA2 page 

• AC off/ on and on HDCP button of MSPG925 and confirm

whether picture is displayed or not of using MSPG925 

• HDCP Key value is different among the sets. 

ITEM

Command

Data Range

Defaulta

(Hex.)

(Decimal)

Cmd 1

Cmd 2

Min

Max

Cool

R-Gain

j

g

00

C0

TBD

G-Gain

j

h

00

C0

TBD

B-Gain

j

i

00

C0

TBD

R-Cut

TBD

G-Cut

TBD

B-Cut

TBD

Medium

R-Gain

j

a

00

C0

TBD

G-Gain

j

b

00

C0

TBD

B-Gain

j

c

00

C0

TBD

R-Cut

TBD

G-Cut

TBD

B-Cut

TBD

Warm

R-Gain

j

d

00

C0

TBD

G-Gain

j

e

00

C0

TBD

B-Gain

j

f

00

C0

TBD

R-Cut

G-Cut

Mode

Color Coordination

Temp

∆UV

x

y

COOL

0.276

0.283

11000K

0.0000

MEDIUM

0.285

0.293

9300K

0.0000

WARM

0.313

0.329

6500K

0.0000

Mode

Color Coordination

Temp

∆UV

x

y

COOL

0.276±0.002

0.283±0.002

11000K

0.0000

MEDIUM

0.285±0.002

0.293±0.002

9300K

0.0000

WARM

0.313+0.002

0.329±0.002

6500K

0.0000

model only, which selects the rating related country.

2) Applied models: LA84A Chassis applied None USA

Model(Canada, Mexico)

1) Press the In-Start key of the R/C and press the red oval

OP1(PIP CH-) key to enter into the Factory Option menu.

2) Select 1.USA, 2.CANADA or 3.MEXICO from the country

select according to the destination. At this time, use the
volume +/- key to adjust 

- After completing the final test, in order to set the set to the

shipping condition, press the In-Stop key of the R/C to make
sure that the set is turned off.

(1) Preparing for the automatic test on the GND & resisting

pressure 

- Make sure that the power cord is completely inserted into

the set. (When it is disconnected or loosened, test after
inserting it)

(2) Perform the automatic test on the GND & resisting pressure

1) The set with power cord, the cord and the A/V

completely inserted into the tuner is loaded on the pallet
and entered into the automatic test process.

2) Connect the D-terminal AV JACK tester
3) Turn on the automatic (GWS103-4)
4) Perform the GND TEST
5) If it is not good, the buzzer is operated to notify the test

result to the operator.

6) If it is OK, it is automatically switched to the resisting

pressure test. (Disconnect the cord and the A/V from the
AV JACK BOX)

6) Perform the resisting pressure test
7) If it is not good, the buzzer is operated to notify the test

result to the operator.

8) If it is OK, the GOOD LAMP is turned and the stopper is

moves down, and it moves to the next process.

(1) TEST voltage

- GND:1.5KV/min at 100mA
- SIGNAL:3KV/min at 100mA

(2) TEST time:1 second
(3) TEST POINT

- GND test = between Power cord GND and Signal cable

metal GND

- Resisting pressure test = between Power cord GND and

Live & Neutral

(4) LEAKAGE CURRENT: Set to 0.5mArms 

The USB download is for the quick service response via the
S/W upgrade and for applying the S/W upgrade necessary for
the board adjustment

1) After turning on the set, make sure that the display screen

is turned on.

2) When the USB Memory Stick with the upgrade file applied

is inserted into the USB jack on the main board, the
following screen (example) is displayed after several
seconds

3) Check the current version at [Current TV Software Version

Information], check the S/W version to upgrade at [New
Found TV Software Version Information], and press the
Enter button of the TV remote controller.

4) Downloading is proceeded as shown at the below screen,

and when it is ended, turning on/off is automatically done.

(When the automatic proceeding is not smoothly done,
manually perform the power On/Off).

5) When downloading is ended, remove the USB Memory

Stick from the USB jack.

6) Press the IN-START button of the remote controller to

check the upgraded S/W version.

- 14 -

- 15 -

- 16 -