LG 37LN548C / 37LN549C / 37LP360H / 37LP361H (CHASSIS:LD3AC) Service Manual ▷ View online
- 13 -
* Auto-control interface and directions
(1) Adjust in the place where the influx of light like floodlight
around is blocked. (illumination is less than 10 lux).
(2) Adhere closely the Color analyzer(CA210) to the module
less than 10 cm distance, keep it with the surface of the
Module and Color analyzer's prove vertically.(80° ~ 100°).
(3) Aging time
- After aging start, keep the power on (no suspension of
power supply) and heat-run over 5 minutes.
- Using 'no signal' or 'POWER ONLY' or the others, check
the back light on.
▪ Auto adjustment Map(using RS-232C to USB cable)
RS-232C COMMAND
[CMD ID DATA]
Wb
00 00
White Balance Start
Wb
00 ff
White Balance End
<Caution>
Color Temperature : COOL, Medium, Warm.
One of R Gain/G Gain/ B Gain should be kept on 0xC0, and
adjust other two lower than C0.(When R/G/B Gain are all
C0, it is the FULL Dynamic Range of Module)
* Manual W/B process using adjust Remote control.
▪ After enter Service Mode by pushing "ADJ" key,
▪ Enter White Balance by pushing "►" key at "8. White
Balance".
* After you finished all adjustments, Press "In-start" key and
compare Tool option and Area option value with its BOM, if
it is correctly same then unplug the AC cable. If it is not
same, then correct it same with BOM and unplug AC cable.
For correct it to the model's module from factory Jig model.
* Push the "IN STOP" key after completing the function
inspection. And Mechanical Power Switch must be set “ON”.
4.5. Outgoing condition Configuration
■ When pressing IN-STOP key by SVC remocon, Red LED
are blinked alternatively. And then automatically turn off.
(Must not AC power OFF during blinking)
5. GND and HI-POT Test
5.1. HI-POT auto-check preparation
- Check the POWER cable and SIGNAL cable insertion condition
5.2. HI-POT auto-check
(1) Pallet moves in the station. (POWER CORD / AV CORD is
tightly inserted)
(2) Connect the AV JACK Tester.
(3) Controller (GWS103-4) on.
(4) HI-POT test (Auto)
- If Test is failed, Buzzer operates.
- If Test is passed, GOOD Lamp on and move to next proc-
ess automatically.
5.3. Checkpoint
(1) Test voltage
- Touchable Metal : 3 KV / min at 100 mA
- SIGNAL : 3KV / min at 100 mA
(2) TEST time: 1 second. (case : mass production )
(3) TEST POINT
- Touchable Metal => LIVE & NEUTRAL : Touchable Metal.
- SIGNAL => LIVE & NEUTRAL : SIGNAL.
6. Model name & Serial number D/L
▪ Press "Power on" key of service remote control.
(Baud rate : 115200 bps)
▪ Connect RS232 Signal Cable to RS-232 Jack.
▪ Write Serial number
▪ Must check the serial number at the Diagnostics of SET UP menu.
(Refer to below).
6.1. Signal Table
CMD : A0h
LENGTH : 85~94h (1~16 bytes)
ADH : EEPROM Sub Address high (00~1F)
ADL : EEPROM Sub Address low (00~FF)
Data : Write data
CS : CMD + LENGTH + ADH + ADL + Data_1 +...+ Data_n
Delay : 20ms
6.2. Command Set
* Description
FOS Default write : <7mode data> write
Vtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 0,
Phase
Data write : Model Name and Serial Number write in EEPROM,.
RS-232C COMMAND
[CMD ID DATA]
MIN
CENTER
(DEFAULT)
MAX
Cool
Mid
Warm
Cool Mid Warm
R Gain
jg
Ja
jd
00
172
192
192
192
G Gain
jh
Jb
je
00
172
192
192
192
B Gain
ji
Jc
jf
00
192
192
172
192
R Cut
64
64
64
128
G Cut
64
64
64
128
B Cut
64
64
64
128
EZ ADJUST
0. Tool Option1
1. Tool Option2
2. Tool Option3
3. Tool Option4
4. Tool Option5
5. Commercial Tool Option
6. Country Group
7. ADC Calibration
1. Tool Option2
2. Tool Option3
3. Tool Option4
4. Tool Option5
5. Commercial Tool Option
6. Country Group
7. ADC Calibration
8. White Balance
►
9. 10 Point WB
10. Test Pattern
11. EDID D/L
12. Sub B/C
13. Ext. Input Adjust
10. Test Pattern
11. EDID D/L
12. Sub B/C
13. Ext. Input Adjust
Whit Balance
Color Temp.
◄
►
R-Gain
G-Gain
B-Gain
R-Cut
G-Cut
B-Cut
Test-Pattern
Backlight
Reset
G-Gain
B-Gain
R-Cut
G-Cut
B-Cut
Test-Pattern
Backlight
Reset
To Set
Cool
172
172
192
172
192
64
64
64
64
64
ON
100
CMD
LENGTH
ADH
ADL
DATA_1
. . .
Data_n
CS
DELAY
Adjust mode
CMD(hex)
LENGTH(hex)
Description
EEPROM WRITE
A0h
84h+n
n-bytes Write (n = 1~16)
- 14 -
6.3. Method & notice
(1) Serial number D/L is using of scan equipment.
(2) Setting of scan equipment operated by Manufacturing
Technology Group.
(3) Serial number D/L must be conformed when it is produced in
production line, because serial number D/L is mandatory by
D-book 4.0.
* Manual Download(Model Name and Serial Number)
If the TV set is downloaded by OTA or Service man, sometimes
model name or serial number is initialized.(Not always)
There is impossible to download by bar code scan, so It need
Manual download.
1) Press the "Instart" key of Adjustment remote control.
2) Go to the menu "6.Model Number D/L" like below photo.
3) Input the Factory model name(ex 32LP360H-ZA) or Serial
number like photo.
4) Check the model name Instart menu. → Factory name displayed.
(ex 32LP360H-ZA)
5) Check the Diagnostics.(DTV country only) → Buyer model
displayed.(ex 32LP360H)
7. CI+ key download
7.1. Communication Prot connection
Connection : PCBA (USB Port)
→
USB to Serial Adapter
(UC-232A)
→
RS-232C cable
→
PC(RS-232C port)
7.2. CI+ Key Download
▪ Set CI+ Key path Directory at Start Mac & CI+ Download
Programme
▪ Com 1,2,3,4 and 115200(Baudrate)
▪ Port connection button click(1)
▪ Push the (2) MAC Address write.
▪ At success Download, check the OK (3).
▪ Start CI+ Key Download, Push the (4).
▪ Check the OK or NG.
GP4_LOW
- 15 -
8. Check Commercial Features.
8.1. External speaker(8OHM, 1W, Single-End)
<Equipment & Condition>
■ External speaker and Oscilloscope
■ Power only mode
(1) Connect external speaker(8 ohm) to speaker out port with
phone jack on TV side as below.
(2) Check the Max. speaker output is 1W or not. Sine wave
with 1KHz will be displayed.
8.2. IR OUT
< Equipment & Condition >
■ Simple Jig (commercial check JIG)
■ Power only mode
(1) Connect each other RS232C port on the Commercial
Check JIG.
(2) Press any key on Service Remote-control.
(3) Check the LED status of the Check JIG.
- IR LED(OK condition: blinking) (LED #1)
- 16 -
TROUBLE SHOOTING GUIDE
1. Check the booting Voltage
;ΒΜΖ͑ΤΦΣΖ͑ΥΙΖ͑΄ΥΒΟΕ͞ΓΪ͑·ΠΝΥΒΘΖ
ͥͤ͑ͪ͡ίͣ͢ΡΚΟ͑ͫ͑ͤͦ͜͟· ΐ΄΅͑
ͥͤ͑ͪ͡ίͣ͢ΡΚΟ͑ͫ͑ͤͦ͜͟· ΐ΄΅͑
;ΒΜΖ͑ΤΦΣΖ͑ΥΙΖ͑;ΚΔΠΞ͑ΧΠΝΥΒΘΖ
ͽͥͥ͑ͫ͑ͤͦ͜͟͡· ΐ΄΅͑
ͽͥͥ͑ͫ͑ͤͦ͜͟͡· ΐ΄΅͑
;ΒΜΖ͑ΤΦΣΖ͑ΥΙΖ͑ʹͽͼ͑ΠΗ͑Ήͣ͢͡
ͺΤ ͑ͣͥ;Ϋ
ͺΤ ͑ͣͥ;Ϋ
;ΒΜΖ͑ΤΦΣΖ͑ΥΙΖ͑ΈΐͿ͑ΠΗ͑ͥͤ͡
͢ΡΚΟ͑ͫ͑ͤͤ͟·
͢ΡΚΟ͑ͫ͑ͤͤ͟·
;ΒΜΖ͑ΤΦΣΖ͑ΥΙΖ͑;ΦΝΥΚ͑·ΠΝΥΒΘΖ
ͥͤ͑ͣ͡ΡΚΟ͑ͫ͑ͣͥ· ͑ͨ͢͝ΡΚΟ͑ͫ͑ͣ͢·
ͥͤ͑ͣ͡ΡΚΟ͑ͫ͑ͣͥ· ͑ͨ͢͝ΡΚΟ͑ͫ͑ͣ͢·
;ΒΜΖ͑ΤΦΣΖ͑ΥΙΖ͑ΦΥΡΦΥ͑·ΠΝΥΒΘΖ͑ΠΗ͑ͺʹ͑ͥͣͤͨ͡͠͠
ͺʹͥͣ͑ͫ͑ͣͦ͟͡· ͑͝ͺʹͥͤͫ͑͢͟͢͡· ͑͝ͺʹͥͨ͑ͫ͑ͦ͢͟͡· ͑ͥͤ͑ͫ͑͝͡ ͤͤ͟·
ͺʹͥͣ͑ͫ͑ͣͦ͟͡· ͑͝ͺʹͥͤͫ͑͢͟͢͡· ͑͝ͺʹͥͨ͑ͫ͑ͦ͢͟͡· ͑ͥͤ͑ͫ͑͝͡ ͤͤ͟·
;ΒΜΖ͑ΤΦΣΖ͑ΥΙΖ͑ΠΨΖΣ͑
ʹΠΟΟΖΔΥΠΣ
ʹΠΟΟΖΔΥΠΣ
;ΒΜΖ͑ΤΦΣΖ͑ΥΙΖ͑ΕΚΤΔΠΟΟΖΔΥΚΠΟ͑ΠΗ͑
;ΒΚΟ͑ΓΠΒΣΕ͑ͤͦ͟· ͑ΔΚΣΔΦΚΥ
;ΒΚΟ͑ΓΠΒΣΕ͑ͤͦ͟· ͑ΔΚΣΔΦΚΥ
ͶΩΔΙΒΟΘΖ͑ΥΙΖ͑
ʹΚΣΔΦΚΥ͑ΓΠΒΣΕ
ʹΚΣΔΦΚΥ͑ΓΠΒΣΕ
;ΒΜΖ͑ΤΦΣΖ͑ΥΙΖ͑ΧΠΝΥΒΘΖ͑ΠΗ͑ͽ· ͵΄͑ΠΨΖΣ
ͥͪ͑ͫ͑ͣ͢͡·
ͥͪ͑ͫ͑ͣ͢͡·
;ΒΜΖ͑ΤΦΣΖ͑ΥΙΖ͑ΠΦΥΡΦΥ͑ΠΗ͑;΄΅Ͳ͑ͽ·͵΄
;ΒΜΖ͑ΤΦΣΖ͑ΥΙΖ͑ͺΟΧΖΣΥΖΣ͑ΔΠΟΥΣΠΝ͑ΒΟΕ͑ΖΣΣΠΣ
ͥͤ͑ͩ͢͡ΡΚΟ͑ͫ͑ΚΘΙ͑ͣͥ͝ΡΚΟ͑ͫ͑ͽΠΨ
ͥͤ͑ͩ͢͡ΡΚΟ͑ͫ͑ΚΘΙ͑ͣͥ͝ΡΚΟ͑ͫ͑ͽΠΨ
ͶΩΔΙΒΟΘΖ͑ΥΙΖ͑ͽʹ͵͑;ΠΕΦΝΖ
ͶΩΔΙΒΟΘΖ͑ΥΙΖ͑ͽͥͥ͡
ͶΩΔΙΒΟΘΖ͑ΥΙΖ͑Ήͣ͢͡
Ζ͞ΕΠΨΟΝΠΒΕ͑ΠΗ͑ͷΚΣΞΨΒΣΖ
ͶΩΔΙΒΟΘΖ͑ΥΙΖ͑ΔΚΣΔΦΚΥ͑ΓΠΒΣΕ
ͶΩΔΙΒΟΘΖ͑ΥΙΖ͑ͺʹͥͣͤͨ͑͡͠͠͝
ͥͤ͡
ͥͤ͡
ͶΩΔΙΒΟΘΖ͑ΥΙΖ͑ͥͪ͡
ͶΩΔΙΒΟΘΖ͑ΥΙΖ͑;ΤΥΒΣ͙ͺʹ͚͢͢͡
Σ͑;ΒΚΟ͑ΓΠΒΣΕ
Σ͑;ΒΚΟ͑ΓΠΒΣΕ
ͶΩΔΙΒΟΘΖ͑ΥΙΖ͑ΔΚΣΔΦΚΥ͑ΠΣ͑ΔΙΖΔΜ
΅ΙΖ͑ͽʹ͵͑ΞΠΕΦΝΖ
΅ΙΖ͑ͽʹ͵͑ΞΠΕΦΝΖ
ͿΠ
ͿΠ
ͿΠ
ͿΠ
ͿΠ
ͿΠ
ͿΠ
ͿΠ
ͿΠ
Ί ΖΤ
Ί ΖΤ
Ί ΖΤ
Ί ΖΤ
Ί ΖΤ
Ί ΖΤ
Ί ΖΤ
Ί ΖΤ
Ί ΖΤ
Ί ΖΤ
Ί ΖΤ
ͿΠ
ͶΩΔΙΒΟΘΖ͑ΥΙΖ͑;ΤΥΒΣ͙ͺʹ͚͢͢͡
Σ͑;ΒΚΟ͑ΓΠΒΣΕ
Σ͑;ΒΚΟ͑ΓΠΒΣΕ
ʹΙΖΔΜ͑ΥΙΖ͑΄ΥΒΟΕ͞ΓΪ͑·ΠΝΥΒΘΖ
ͥͤ͑ͪ͡ίͣ͢ΡΚΟ͑ͫ͑ͤͦ͜͟· ΐ΄΅͑
ͥͤ͑ͪ͡ίͣ͢ΡΚΟ͑ͫ͑ͤͦ͜͟· ΐ΄΅͑
ʹΙΖΔΜ͑ΥΙΖ͑΅ΦΟΖΣ͑ͤͤ͟· ͑
ͬ͑ͽͤͨͤ͡
ͬ͑ͽͤͨͤ͡
ʹΙΖΔΜ͑ΥΙΖ͑΅ΦΟΖΣ͑ͩ͢͟·
ͺʹͤͨͤ͑ͣ͡ΡΚΟ͑ͫ͑ͩ͢͟·
ͺʹͤͨͤ͑ͣ͡ΡΚΟ͑ͫ͑ͩ͢͟·
ʹΙΖΔΜ͑ΥΙΖ͑ͺͷΐ͠Ϳ͑Τ ΚΘΟΒΝ
΅Άͤͨͥ͑͢͢͢͡͡͠ΡΚΟ
΅Άͤͨͥ͑͢͢͢͡͡͠ΡΚΟ
ʹΙΖΔΜ͑ΥΙΖ͑ͽ· ͵΄͑ΠΦΥΡΦΥ͑ΤΚΘΟΒΝ͑ΠΗ͑;ΤΥΒΣ͑ͺʹ
ͶΩΔΙΒΟΘΖ͑ΥΙΖ͑ͽͤͨͤ͡
ͶΩΔΙΒΟΘΖ͑ΥΙΖ͑ͺʹͤͨͤ͡
ͶΩΔΙΒΟΘΖ͑ΥΙΖ͑΅ΦΟΖΣ
ͶΩΔΙΒΟΘΖ͑ΥΙΖ͑;ΤΥΒΣ͙ͺʹ͚͢͢͡
Σ͑;ΒΚΟ͑ΓΠΒΣΕ
Σ͑;ΒΚΟ͑ΓΠΒΣΕ
ͿΠ
ͿΠ
ͿΠ
ͿΠ
Ί ΖΤ
Ί ΖΤ
Ί ΖΤ
Ί ΖΤ
2. Digital TV Video
Click on the first or last page to see other 37LN548C / 37LN549C / 37LP360H / 37LP361H (CHASSIS:LD3AC) service manuals if exist.