DOWNLOAD LG 37LG50 (CHASSIS:LA84A) Service Manual ↓ Size: 4.28 MB | Pages: 29 in PDF or view online for FREE

- 13 -

3.3.2 ADC 1080p Comp1/RGB

1) Check the connection condition of Component1 and

RGB from the device to use.

2) Apply 1080p Mode, 100% Horizontal Color Bar Pattern

to Comp1 and RGB port.

(MSPG-925 Series => model:225 , pattern:65 )

3) Set the input to Component1 and select °ÆNormal°Ø

as video.

4) Wait for one second or longer after receiving the signal,

press the ADJ key of the R/C to enter into 'Ez-Adjust',
select '4. ADC 1080p Comp1/RGB', and press the
Enter key to automatically adjust the component1.

5) If it is normally adjusted, the message "ADC

Component1 Success" is displayed, or if not, the
message 'ADC Component1 1080p Fail' is displayed.

6) When adjusting the Component1 is ended, it is

automatically switched to the RGB-DTV Mode and the
RGT adjustment is started. If it is normally adjusted, the
message "ADC RGB 1080P Success" is displayed.

7) If it is not normally adjusted, check the pattern or the

adjustment condition, and then readjust. The error
message is same to 6).

8) If the adjustment is ended, press the ADJ key to exit

from the adjustment mode. If the 7) adjustment is
ended, press the ADJ or the Exit of the adjustment R/C
to exit from the adjustment mode.

VESA specification. Function to implement the "Plug and
Play" for automatically reconfiguring the user°Øs environment
to directly use by exchanging the information with no direct
command to the PC or the monitor from the user. 

- PC (S/W included: EDID Data Write & Read)
- EDID DOWNLOAD JIG
- HDMI Cable, D-sub Cable

1) Configure the download environment as shown at the

adjustment wiring diagram and turn on the PC.

2) Execute the DDC program. (EDID Data Write & Read)
3) Go to Model -> Open, and select the EDID data of the

desired model.

4) Check the item to download from the <Test> item
4-1) HDMI & RGB: Check Digital & Analog
4-2) (Only)HDMI: Check Digital only
5) Press ESC(Cancel Mode) -> F8(Auto Mode). (Set Auto

Detecting)

6) Connect the desired signal cable to the set.
7) Make sure that the popup "Proceed to write?" is displayed.
8) Press the Enter key or the space key to download.
9) After downloading, check the OK message and disconnect

the connected cable.

LCD TV SET

(or VSC Board)

USB

D-SUB 

DVI to HDMI

Device configuration diagram for HDMI EDID Data input

- 14 -

Note) Because downloading can be down at the power on

mode only, if it is not set, press the Power ON key of

the remote controller to proceed.

O  

HDMI1  EDID (DDC (Display Data Channel) Data 

O  

HDMI2  EDID (DDC (Display Data Channel) Data

O  

HDMI3  EDID (DDC (Display Data Channel) Data

O  

Analog (RGB) EDID table

0

1

2

3

4

5

6

7

8

9

A

B

C

D

E

F

0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01

10 00 11 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23
20 09 48 4C AF CF 00 31 40 45 40 61 40 81 80 A9 40
30 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
40 36 00 C4 8E 21 00 00 1E 02 3A 80 18 71 38 2D 40
50 58 2C 45 00 C4 8E 21 00 00 1E 00 00 00 FD 00 30
60 58 1F 64 11 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 8A

0

1

2

3

4

5

6

7

8

9

A

B

C

D

E

F

0 02 03 18 F1 47 84 05 03 02 20 22 10 23 15 07 50

10 67 03 0C 00 10 00 B8 2D 01 1D 00 72 51 D0 1E 20
20 6E 28 55 00 C4 8E 21 00 00 1E 01 1D 80 18 71 1C
30 16 20 58 2C 25 00 C4 8E 21 00 00 9E 8C 0A D0 8A
40 20 E0 2D 10 10 3E 96 00 C4 8E 21 00 00 18 8C 0A
50 D0 8A 20 E0 2D 10 10 3E 96 00 13 8E 21 00 00 18
60 26 36 80 A0 70 38 1F 40 30 20 25 00 C4 8E 21 00
70 00 1A 00 00 00 00 00 00 00 00 00 00 00 00 00 27

0

1

2

3

4

5

6

7

8

9

A

B

C

D

E

F

0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01

10 00 11 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23
20 09 48 4C AF CF 00 31 40 45 40 61 40 81 80 A9 40
30 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
40 36 00 C4 8E 21 00 00 1E 02 3A 80 18 71 38 2D 40
50 58 2C 45 00 C4 8E 21 00 00 1E 00 00 00 FD 00 30
60 58 1F 64 11 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 8A

0

1

2

3

4

5

6

7

8

9

A

B

C

D

E

F

0 02 03 18 F1 47 84 05 03 02 20 22 10 23 15 07 50

10 67 03 0C 00 30 00 98 25 01 1D 00 72 51 D0 1E 20
20 6E 28 55 00 C4 8E 21 00 00 1E 01 1D 80 18 71 1C
30 16 20 58 2C 25 00 C4 8E 21 00 00 9E 8C 0A D0 8A
40 20 E0 2D 10 10 3E 96 00 C4 8E 21 00 00 18 8C 0A
50 D0 8A 20 E0 2D 10 10 3E 96 00 13 8E 21 00 00 18
60 26 36 80 A0 70 38 1F 40 30 20 25 00 C4 8E 21 00
70 00 1A 00 00 00 00 00 00 00 00 00 00 00 00 00 2F

0

1

2

3

4

5

6

7

8

9

A

B

C

D

E

F

0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01

10 00 11 01 03 18 73 41 96 0A CF 74 A3 57 4C B0 23
20 09 48 4C AF CF 00 31 40 45 40 61 40 81 80 A9 40
30 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
40 36 00 C4 8E 21 00 00 1A 02 3A 80 18 71 38 2D 40
50 58 2C 45 00 C4 8E 21 00 00 1E 00 00 00 FD 00 30
60 58 1F 64 11 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 F6

0

1

2

3

4

5

6

7

8

9

A

B

C

D

E

F

0 02 03 04 00 0E 1F 00 80 51 00 1E 30 40 80 37 00

10 C4 8E 21 00 00 1C F1 27 00 A0 51 00 25 30 50 80
20 37 00 C4 8E 21 00 00 1C 26 36 80 A0 70 38 1F 40
30 30 20 25 00 C4 8E 21 00 00 0A 00 00 00 00 00 00
40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 BC

0

1

2

3

4

5

6

7

8

9

A

B

C

D

E

F

0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01

10 00 11 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23
20 09 48 4C AF CF 00 31 40 45 40 61 40 81 80 A9 40
30 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
40 36 00 C4 8E 21 00 00 1E 02 3A 80 18 71 38 2D 40
50 58 2C 45 00 C4 8E 21 00 00 1E 00 00 00 FD 00 30
60 58 1F 64 11 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 8A

0

1

2

3

4

5

6

7

8

9

A

B

C

D

E

F

0 02 03 18 F1 47 84 05 03 02 20 22 10 23 15 07 50

10 67 03 0C 00 20 00 B8 2D 01 1D 00 72 51 D0 1E 20
20 6E 28 55 00 C4 8E 21 00 00 1E 01 1D 80 18 71 1C
30 16 20 58 2C 25 00 C4 8E 21 00 00 9E 8C 0A D0 8A
40 20 E0 2D 10 10 3E 96 00 C4 8E 21 00 00 18 8C 0A
50 D0 8A 20 E0 2D 10 10 3E 96 00 13 8E 21 00 00 18
60 26 36 80 A0 70 38 1F 40 30 20 25 00 C4 8E 21 00
70 00 1A 00 00 00 00 00 00 00 00 00 00 00 00 00 17

- 15 -

- Purpose and principle for adjusting the white balance
- Purpose : Adjust the white balance to reduce the deviation

of the module.

- Principle: The full dynamic range of the module when the

RGB gain on the OSD is 192. In order to adjust the white
balance with no saturation of the full dynamic range and the
data, fix one of the RGB gains to 192 and decrease the
remaining two gains to adjust

1) Color Analyzer : CA-210 (NCG: CH 9 / WCG: CH12)
2) Computer to adjust (needed for the automatic adjustment,

possible to communicate with the RS-232C)

3) Adjustment remote controller
4) Video Signal Generator MSPG-925F 720p/216Gray

(Model:217, Pattern:78)

=> Applied only when the inner pattern cannot be used

*Use the Color Analyzer with the matrix calibrated by the CS-

1000

- "wb 00 00": Start Auto-adjustment of white balance.
- "wb 00 10": Start Gain Adjustment (Inner pattern) 
- "jb 00 c0" : 
- …
- "wb 00 1f": End of Adjustment

* If it needs, offset adjustment (wb 00 20-start, wb 00 2f-

end)

- "wb 00 ff": End of white balance adjustment (inner pattern

disappear)

1) The adjustment condition should be set by the Power On

key.

2) Perform the zero calibration of the Color Analyzer and

place the probe close to the display center.

3) Connect the communication cable (RS-232C).
4) Select the desired model of the adjustment program and

perform the adjustment.

5) After the adjustment is ended (check the OK sign), check

the adjustment condition for each mode of the set.

(Warm, Medium, Cool)

6) Disconnect the probe and the communication cable to end

the adjustment.

* The adjustment should be started with "wb 00 00" and ended

with "wb 00 ff", and the offset should be adjusted when
necessary.

1) The adjustment condition should be set by the Power On

key.

2) Press the ADJ of the R/C to enter into 'EZ-ADJUST'.
3) Select '10.TEST PATTERN' with the CH +/- key and press

the Enter key for 30 minutes or longer to perform the heat
run.

4) Perform the zero calibration of the Color Analyzer and fix

the sensor with the 10cm or less distance at the center of
the LCD module surface when adjusting.

5) Press the ADJ of the R/C to select '7.White-Balance' of the

Ez-Adjust and press the right arrow key(

G

) to enter into

the adjustment mode.

(As soon as you press '

G

', the screen is entered into the

full white inner pattern.)

6) Fix one of the R/G/B gains to 192 and decrease the

remaining two gains to adjust not to exceed 192.

7) The adjustment is done at three white balances of Cool,

Medium and Warm.

* The inner pattern is basically used, and if it is not possible, the

adjustment can be done by selecting the HDMI input. NONE,
INNER or HDMI can be selected by the bottom option at the Ez
Adjust Menu 7.White Balance menu and it is set to INNER as
default. If the adjustment cannot be done by the inner pattern,
select the HDMI to adjust.

* Adjustment environment and reference

1) Environment illuminance

Adjust it to 10 LUX or less at the place where the light
source such as lamp should be blocked at maximum.

2) Probe location

- PDP: Locate the Color Analyzer (CA-100, CA-100+,

CA210) close to the module surface to measure and
adjust

- LCD: Maintain  the  Color Analyzer (CA-210) close to the

module surface by 10cm or less and keep the probe
of the Color Analyzer perpendicular to the module
surface (80°~ 100°).

3) Aging time

- Keep the power on after the aging start (with no power off)

to perform the heat run for 15 minutes or longer.

- Keep the white pattern with the inner pattern for the PDP.
- For the LCD, make sure that the back light is turned on by

using no signal and the full white pattern or others.

RS-232C COMMAND

Meaning

[CMD    ID      DATA]

wb

00

00

White Balance adjustment start.

wb

00

10

Start of adjust gain (Inner white pattern)

wb

00

1f

End of gain adjust

wb

00

20

Start of offset adjust(Inner white pattern)

wb

00

2f

End of offset adjust

wb

00

ff

End of White Balance adjust(Inner pattern disappeared)

- 16 -

O  

Brightness: Full white 216 Gray 

O  

Standard color coordinate and white balance when using the

CS-1000

O  

Standard color coordinate and white balance when using the
CA-210 (CH 10)

only, which selects the rating related country.

- Applied models: LA84A Chassis applied None USA

Model(Canada, Mexico)

1) Press the In-Start key of the R/C and press the red oval

OP1(PIP CH-) key to enter into the Factory Option menu.

2) Select 1.USA, 2.CANADA or 3.MEXICO from the country

select according to the destination. At this time, use the
volume +/- key to adjust

- After completing the final test, in order to set the set to the

shipping condition, press the In-Stop key of the R/C to make
sure that the set is turned off.

1) Preparing for the automatic test on the GND & resisting

pressure

- Make sure that the power cord is completely inserted into

the set. (When it is disconnected or loosened, test after
inserting it)

2) Perform the automatic test on the GND & resisting

pressure

- The set with power cord, the cord and the A/V completely

inserted into the tuner is loaded on the pallet and entered
into the automatic test process.

- Connect the D-terminal AV JACK tester
- Turn on the automatic (GWS103-4)
- Perform the GND TEST
- If it is not good, the buzzer is operated to notify the test

result to the operator.

- If it is OK, it is automatically switched to the resisting

pressure test. (Disconnect the cord and the A/V from the
AV JACK BOX)

- Perform the resisting pressure test

- If it is not good, the buzzer is operated to notify the test

result to the operator.

- If it is OK, the GOOD LAMP is turned and the stopper is

moves down, and it moves to the next process.

O  

TEST voltage

- GND:1.5KV/min at 100mA
- SIGNAL:3KV/min at 100mA

O

TEST time:1 second

O  

TEST POINT

- GND TEST = between POWER CORD GND and

SIGNAL CABLE METAL GND

- Resisting pressure TEST = between POWER CORD

GND and LIVE & NEUTRAL

O  

LEAKAGE CURRENT: Set to 0.5mArms 

Color temperature

Color Coordination         

Temp

UV

x

y

COOL

0.276

0.283

11000K

0.0000

MEDIUM

0.285

0.293

9300K

0.0000

WARM

0.313

0.324

6500K

0.0000

Color temperature Test Equipment

Color Coordination

x

y

COOL

CA-210

0.276±0.002

0.283±0.002

MEDIUM

CA-210

0.285±0.002

0.293±0.002

WARM

CA-210

0.313±0.002

0.329±0.002