DOWNLOAD LG 37LD460 (CHASSIS:LL01B) Service Manual ↓ Size: 8.99 MB | Pages: 73 in PDF or view online for FREE

Model
37LD460 (CHASSIS:LL01B)
Pages
73
Size
8.99 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / LCD
File
37ld460-chassis-ll01b.pdf
Date

LG 37LD460 (CHASSIS:LL01B) Service Manual ▷ View online

- 5 -
IC Remove/Replacement
Some chassis circuit boards have slotted holes (oblong) through
which the IC leads are inserted and then bent flat against the
circuit foil. When holes are the slotted type, the following technique
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique
as outlined in paragraphs 5 and 6 above.
Removal
1.  Desolder and straighten each IC lead in one operation by gently
prying up on the lead with the soldering iron tip as the solder
melts.
2.  Draw away the melted solder with an anti-static suction-type
solder removal device (or with solder braid) before removing the
IC.
Replacement
1.  Carefully insert the replacement IC in the circuit board.
2.  Carefully bend each IC lead against the circuit foil pad and
solder it.
3.  Clean the soldered areas with a small wire-bristle brush.
(It is not necessary to reapply acrylic coating to the areas).
"Small-Signal" Discrete Transistor
Removal/Replacement
1.  Remove the defective transistor by clipping its leads as close as
possible to the component body.
2.  Bend into a "U" shape the end of each of three leads remaining
on the circuit board.
3.  Bend into a "U" shape the replacement transistor leads.
4.  Connect the replacement transistor leads to the corresponding
leads extending from the circuit board and crimp the "U" with
long nose pliers to insure metal to metal contact then solder
each connection.
Power Output, Transistor Device
Removal/Replacement
1.  Heat and remove all solder from around the transistor leads.
2. Remove the heat sink mounting screw (if so equipped).
3.  Carefully remove the transistor from the heat sink of the circuit
board.
4.  Insert new transistor in the circuit board.
5. Solder each transistor lead, and clip off excess lead.
6.  Replace heat sink.
Diode Removal/Replacement
1.  Remove defective diode by clipping its leads as close as
possible to diode body.
2.  Bend the two remaining leads perpendicular y to the circuit
board.
3.  Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4.  Securely crimp each connection and solder it.
5.
Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.
Fuse and Conventional Resistor
Removal/Replacement
1.  Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2.  Securely crimp the leads of replacement component around
notch at stake top.
3.  Solder the connections.
CAUTION: Maintain original spacing between the replaced
component and adjacent components and the circuit board to
prevent excessive component temperatures.
Circuit Board Foil Repair
Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
board causing the foil to separate from or "lift-off" the board. The
following guidelines and procedures should be followed whenever
this condition is encountered.
At IC Connections
To repair a defective copper pattern at IC connections use the
following procedure to install a jumper wire on the copper pattern
side of the circuit board. (Use this technique only on IC
connections).
1.  Carefully remove the damaged copper pattern with a sharp
knife. (Remove only as much copper as absolutely necessary).
2.  carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.
3.  Bend a small "U" in one end of a small gauge jumper wire and
carefully crimp it around the IC pin. Solder the IC connection.
4.  Route the jumper wire along the path of the out-away copper
pattern and let it overlap the previously scraped end of the good
copper pattern. Solder the overlapped area and clip off any
excess jumper wire.
At Other Connections
Use the following technique to repair the defective copper pattern
at connections other than IC Pins. This technique involves the
installation of a jumper wire on the component side of the circuit
board.
1.  Remove the defective copper pattern with a sharp knife.
Remove at least 1/4 inch of copper, to ensure that a hazardous
condition will not exist if the jumper wire opens.
2.  Trace along the copper pattern from both sides of the pattern
break and locate the nearest component that is directly
connected to the affected copper pattern.
3.  Connect insulated 20-gauge jumper wire from the lead of the
nearest component on one side of the pattern break to the lead
of the nearest component on the other side.
Carefully crimp and solder the connections.
CAUTION: Be sure the insulated jumper wire is dressed so the
it does not touch components or sharp edges.
- 6 -
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application range
This specification is applied to the 32”/37”/42”/47” LCD TV
used LL01B chassis.
2. Requirement for Test
Each part is tested as below without special appointment.
1) Temperature :  25 ºC ± 5 ºC (77 ºF ± 9 ºF), CST : 40ºC  ± 5 ºC
2) Relative Humidity :  65 ± 10 %
3) Power Voltage : Standard input voltage (100-240V~50/60Hz)
* Standard Voltage of each products is marked by models.
4) Specification and performance of each parts are followed
each drawing and specification by part number in
accordance with BOM.
5) The receiver must be operated for about 5 minutes prior to
the adjustment.
3. Test method
1) Performance: LGE TV test method followed 
2) Demanded other specification 
- Safety: CE / ICE specification
EMI: CE / ICE
- 7 -
4. Chroma& Brightness
4.1. Module optical specification
*** LGD module Uniformity Measurement Position*** 
P1
P2
P3
P4
P5
1W/4
2W/4
3W/4
1H/4
2H/4
3H/4
: Measurement position (5 point)
1) Optical characteristics are determined after the unit has been ‘ON’ and stable in a dark environment at 25 °C ± 2 °C
2) Surface luminance is the luminance value at center 1-point across the LCD surface 50cm from the surface with all pixels
displaying white.
No.
Item Specification 
Min.
Typ.
Max.
Remark
1.
Viewing Angle<CR>10> 
Right/Left/Up/Down 
70
88
CR > 10
Luminance (cd/m
2
)
360 450
2.
Luminance
Variation -
1.25 
3.
Contrast Ratio 
CR 
4000 
5000
All white/ All black
White WX
0.278 
WY Typ
0.285
Typ 
RED Xr
0.03
0.641
+0.03
4.
CIE Color Coordinates
Yr
0.344
Green Xg
0.280
Yg
0.607
Blue Xb 
0.144
Yb  
0.072
4.1.1. 32” LCD Module (SHARP) LK315D3LA57
- 8 -
1) Optical characteristics are determined after the unit has been ‘ON’ and stable in a dark environment at 25±2°C
2) Surface luminance is the luminance value at center 1-point across the LCD surface 50cm from the surface with all pixels
displaying white.
No.
Item Specification 
Min.
Typ.
Max.
Remark
1.
Viewing Angle<CR>10> 
Right/Left/Up/Down 
89
CR > 10
Luminance (cd/m
2
)
400 500
2.
Luminance
Variation -
1.3 
3.
Contrast Ratio 
CR 
1000 
1400
All white/ All black
White WX
0.279 
WY Typ
0.292
Typ 
RED Xr
0.03
0.642
+0.03
4.
CIE Color Coordinates
Yr
0.334
Green Xg
0.292
Yg
0.607
Blue Xb 
0.146
Yb  
0.056
4.1.2. 32” LCD Module (LGD) LC320WUG-SCA1
1) Optical characteristics are determined after the unit has been ‘ON’ and stable in a dark environment at 25±2°C
2) Surface luminance is the luminance value at center 1-point across the LCD surface 50cm from the surface with all pixels
displaying white.
No.
Item Specification 
Min.
Typ.
Max.
Remark
1.
Viewing Angle<CR>10> 
Right/Left/Up/Down 
89
CR > 10
Luminance (cd/m
2
)
400 500
2.
Luminance
Variation -
1.3 
3.
Contrast Ratio 
CR 
1100 
1500
All white/ All black
White WX
0.279 
WY Typ
0.292
Typ 
RED Xr
0.03
0.639
+0.03
4.
CIE Color Coordinates
Yr
0.334
Green Xg
0.289
Yg
0.606
Blue Xb 
0.145
Yb  
0.065
4.1.3. 37” LCD Module (LGD) LC370WUG-SCA1
Page of 73
Display

Click on the first or last page to see other 37LD460 (CHASSIS:LL01B) service manuals if exist.