DOWNLOAD LG 37LC2RHA / 37HIZ22 (CHASSIS:LP62F) Service Manual ↓ Size: 3.72 MB | Pages: 45 in PDF or view online for FREE

- 10 -

No

Resolution

H-freq(kHz)

V-freq.(kHz)

Pixel clock(MHz)

Remarks

1.

720 x 480

31.47

59.94

27.000

SDTV 480P

2.

720 x 480

31.50

60.00

27.027

SDTV 480P

3.

720 x 576

31.25

50.00

27.000

SDTV 576P

4.

1280 x 720

44.96

59.94

74.176

HDTV 720P

5.

1280 x 720

45.00

60.00

74.250

HDTV 720P

6.

1280 x 720

37.50

50.00

74.25

HDTV 720P 50Hz

7.

1920 x 1080

33.72

59.94

74.176

HDTV 1080I

8.

1920 x 1080

33.75

60.00

74.250

HDTV 1080I

9.

1920 x 1080

28.125

50.00

74.250

HDTV 1080I 50Hz

No

Item

Content

Remark

1.

Product

Width

Length

Height

Unit

Dimension

Before Packing

944

286

729

mm

SET(With Stand)

After Packing

1052

383

858

mm

2.

Product Weight

Only SET

29.5

Kg

With BOX

35.5

Kg

3. 

Container Loading

Individual or

20ft

40ft

Quantity

Palletizing

Indi

Wooden

Indi

Wooden

60

60

132

132

4.

Stand Assy

Type

Attached ( detachable )

Size( W x D x H )

561

286.3

221.6

mm

Tilt Degree

-

Without Tilt function

Tilt force

-

Swivel Degree

-

Swivel Force

-

5.

Appearance

General

Refer to Standard of LG(55)G1-1020

This spec. sheet is applied to all of the LP62F chassis(H3-
High) manufactured at LG TV Plant all over the world.  

1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation
transformer will help to protect test instruments.

2) Adjustment must be done in the correct sequence.
3) The adjustment must be performed at 25±5°C temperature

and 65±10% relative humidity if there is no specified
designation.

4) The input voltage of the receiver must be kept between

100-220V, 50/60Hz.

5) Before adjustment, execute Heat-Run for 30 minutes at RF

no signal

1) Channel memory

- Download the channel data from BOM to EEPROM by

using LGIDS.

2) Option adjustment following BOM 

- Tool Option1
- Tool Option2
- Area Option

1) Auto AV(ZH-AV3, TH-AV1) Color Balance
2) Aging (by Power on key)
3) Adjustment of White Balance
4) Auto Component Color Balance adjustment

- Standard equipment : MSPG925FA

5) Auto RGB Color Balance adjustment

- Standard equipment : MSPG925FA

[Caution]

* Use the proper signal cable for EDID Download

- Analog EDID : Pin3 exists
- Digital EDID  : Pin3 exists

* Never connect HDMI & DVI-D & DVI-A cable at the same time.
* Use the proper cables below for EDID Writing.

(1) ANALOG(256 Bytes )

- BLOCK1 (128BYTE)

(2) HDMI(256 Bytes )

- BLOCK1 (128BYTE)

- BLOCK2 (128BYTE)

=> Detail EDID Options are below (a, b, c, d, e) 
a. Product ID

b. Serial No :  Controlled on production line
c. Month, Year : Controlled on production line:  

ex) Monthly : '03' => '03' 

Year    :  '2005' =>  '0F'

d. Model Name/Monitor Name

e. Checksum: Changeable by total EDID data

- 11 -

00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

00 00 FF FF FF FF FF FF FF 1E 6D
10

01 03 80 46 27 78 EA D9 B0 A3 57 49 9C 25

20 11 49 4B A5 6E 80 31 40 01 01 01 01 45 40 01 01
30 61 40 01 01 01 01 1B 21 50 A0 51 00 1E 30 48 88
40 35 00 BC 88 21 00 00 1C 4E 1F 00 80 51 00 1E 30
50 40 80 37 00 BC 88 21 00 00 18
60

00 00 00 FD

70 00 38 4B 1F 3D 09 00 0A 20 20 20 20 20 20 01 14

00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

00 02 03 24 F1 49 85 04 02 01 03 11 12 13 14 23 09
10 07 07 23 09 07 07 23 09 07 07 83 01 00 00 65 03
20 0C 00 10 00 01 1D 00 80 51 D0 1C 20 40 80 35 00
30 BC 88 21 00 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E
40 96 00 13 8E 21 00 00 18 2A 12 00 10 41 43 17 20
50 28 60 35 00 00 00 32 00 00 1C 01 1D 80 18 71 1C
60 16 20 58 2C 25 00 C4 8E 21 00 00 9E 00 00 00 00
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 6B

For Analog EDID

D-sub to DVI-I

For Digital EDID

DVI-D to DVI-D

For HDMI EDID

DVI-D to HDMI or HDMI to HDMI

No.

1

2

3

Item

Manufacturer ID

Version

Revision

Condition

GSM

Digital : 1

Digital : 3

Data

1E6D

01

03

a

b

00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

00 00 FF FF FF FF FF FF FF 1E 6D
10

01 03 01 46 27 78 EA D9 B0 A3 57 49 9C 25

20 11 49 4B A5 6E 80 31 40 01 01 01 01 45 40 01 01
30 61 40 01 01 01 01 1B 21 50 A0 51 00 1E 30 48 88
40 35 00 BC 88 21 00 00 1C 4E 1F 00 80 51 00 1E 30
50 40 80 37 00 BC 88 21 00 00 18 00 00 00 FD 00 38
60 4B 1F 3D 09 00 0A 20 20 20 20 20 20
70

00 99

c

a

b

d

d

d

d

Model Name

Product ID

Product ID

Dec

Hex

EDID table

37LC2RHA

30117(A)

30117

75A5

A575

30118(D)

30118

75A6

A675

Model Name

37LC2RHA-ZH 00 00 00 FC 00 33 37 4C 43 32 52 48 41 2D 5A 48 0A 20

- 12 -

* Caution : System control RS-232C Host should be “PC” for

adjustment

- Press the FRONT-AV KEY on remote control for converting

input mode

(Change RS-232C Host : pc, Band Rate : 115200bps)

1) Remote controller for adjustment
2) 802F Pattern Generator, Master (MSPG-925FA), etc.
3) MSPG-925FA Pattern Generator

(Which has Video Signal: 100% Color Bar Pattern
shown in Fig. 1)
=> Model : 202 / Pattern: 33 (PAL : ZH, TH)

Model : 201 / Pattern : 33 (NTSC : MH)

1) Press the FRONT-AV KEY on remote control for

converting input mode.

2) Input the Video Signal: 100% Color Bar signal into

AV3(ZH), AV1(TH), VIDEO1(MH).

3) Set the PSM to Standard mode in the Picture menu.
4) Press INSTART key on remote control for adjustment.
5) Press the 

G

(Vol.+) key to operate the set, then it

becomes automatically.

6) Auto-RGB OK means the adjustment is completed.

1) This AV color balance adjustment should be performed

before White Balance Adjustment.

2) After AV color balance adjustment, Change the mode

from AV to RF. (Cancel Heat-run mode.)

1) Remote controller for adjustment
2) 802F Pattern Generator, Master (MSPG-925FA), etc.
3) MSPG-925FA Pattern Generator 

(Which has 720p YPbPr signal : 100% Color Bar Pattern
shown in Fig. 2 )
=> Model: 217 / Pattern: 33

4) It is very import to use correct adjustment pattern like Fig.1.

- Within the pattern, color sequence should be aligned

: White-Yellow-Cyan-Green-Magenta-Red-Blue-Black
(If color sequence is reversed (Black -> ... -> White),
reverse the pattern with REV key, when using Master
pattern generator like MSPG-925)

- If Minimum Black Level and/or Maximum White Level

is not correct, select 100% Color Bar Pattern.

1) Input the Component 720p 100% Color Bar(MSPG-

925FA model:217, pattern:33) signal into Component.
(ZH : component , TH/MH : component 1 or 2)

2) Set the PSM to Standard mode in the Picture menu.
3) Press the INSTART key on remote control for

adjustment.

4) Press the 

G

(Vol. +) key to operate the set , then it

becomes automatically.

5) Auto-RGB OK means the adjustment is completed.

1) Remote controller for adjustment
2) 802F Pattern Generator, Master (MSPG-925FA), etc.
3) MSPG-925FA Pattern Generator

(Which has XGA [1024x768] 60Hz PC Format output
signal : 100% Color Bar Pattern shown in Fig. 1)

4) It is very import to use correct adjustment pattern like Fig.1.

- Within the pattern, color sequence should be aligned.

: White-Yellow-Cyan-Green-Magenta-Red-Blue-Black
(If color sequence is reversed (Black ->...-> White),
reverse the pattern with REV key, when using Master
pattern generator like MSPG-925).

- If Minimum Black Level and/or Maximum White Level

is not correct, Do select 100% Color Bar Pattern.

1) Input the PC 1024x768 @ 60Hz 1/2 Black & White

Pattern (MSPG-925FA model : 3, patter : 3) into RGB.

2) Set the PSM to Standard mode in Picture menu.
3) Press the INSTART key on remote control for adjustment.
4) Press the 

G

(Vol. +) key operate To set , then it becomes

automatically.

5) Auto-RGB OK means adjustment is completed.

Notice : Before White-balance, change input mode.

Move to AV3(ZH) or AV1(TH) or VIDEO1(MH) by using
the FRONT-AV KEY on Remote controller.

<Caution>

- System control RS-232 Host should be "PC" for

adjustment.

- AV ADC(ZH: AV3, TH : AV1, MH: VIDEO1) should be

done before White-balance.

MSPG-

925FA

AV ADC Condition

PAL

NTSC

Input

ZH model:AV3

MH model

-select

TH model:AV1

:VIDEO1

Model:202(PAL-BGDHI)

Model:201(NTSC)

Pattern :33

*100% Color Bar

Component

Model : 217

DVI(RGB)

Model : 3 

(1024x768@6

0Hz)

<Fig. 1>

White balance

ZH(AV3), TH(AV1)

MH(VIDEO1)

MSPG925FA  216 Level (85IRE)

Model : 202

Model : 201

Full screen pattern

* Pal Video

* NTSC Video

* Test Equipment

Color Analyzer (CA-110)
PC(For communication through RS-232C)
=>UART Baud rate : 115200
Pattern Generator (MSPG-925FA etc.)

*Target Value [ PSM: Standard(ZH/TH), CSM: Normal]

- Normal(9300K±1000K) x:283±0.015, y: 298±0.015
- Luminance(Y)

AV/COPM  : Min. 250 Cd/m

2

(Typ : 300 Cd/m

2

)

PC 

: Min. 300 Cd/m

2

(Typ : 350 Cd/m

2

)

=> Reference Value(Automatically fixed)

- Cool (11000K ± 1000K)
- Warm (7200K ± 1000K)

1) Execute CA-110 Zero Calibration.
2) Execute the SET Heat Run for 30minutes.
3) As below Fig.2, Supply 216Level (85 IRE) full screen

pattern to Video input. AV3/ AV4 (Input 50Hz)

4) Press the FRONT-AV KEY on remote control for converting

input mode.

5) Set the PSM to Standard mode in Picture menu.
6) Enter the White Balance adjustment mode by pressing the

INSTART key twice (White Balance) on remote control.

7) Stick sensor to center of the screen and select each items

(Red/Green/Blue Gain and Offset) using 

D

/

E

(CH+/-) key

on remote control.

8) Adjust Only High Light with R Gain/B Gain using 

F

/

G

(VOL

+/-) key on remote control.

9) Adjust it until color coordination becomes as below. 

(Initially, R/G/B gain and R/G/B offset values are fixed as
below.
Red Gain : 82,

Green Gain : 80,

Blue Gain : 86

Red Offset : 80,

Green Offset : 80,

Blue Offset : 8C)

10) Adjust High light with R/B Gain.

1) LPL Module

2) AUO Module

* Input Select Data

RF(10), AV1~4(20,21,22,23), SAV(30), COMP(40), DVI
(50or60), HDMI(90)

* Command Set (SET ID : 0-> ALL , 1~99 -> each SET)

- 13 -

<Fig. 2>

216 Level(85IRE)

Command1 Command2 Set ID

Data

Min

Max

Input Select

XB

B

00

00h

90h

R-Gain

J

A

00

00h

E0h

G-Gain

J

B

00

00h

E0h

B-Gain

J

C

00

00h

E0h

R-Offset

J

D

00

00h

90h

G-Offset

J

E

00

00h

90h

B-Offset

J

F

00

00h

90h

Command1 Command2 Set ID

Data

Min

Max

Input Select

XB

B

00

00h

90h

R-Gain

J

A

00

00h

E0h

G-Gain

J

B

00

00h

E0h

B-Gain

J

C

00

00h

E0h

R-Offset

J

D

00

00h

90h

G-Offset

J

E

00

00h

90h

B-Offset

J

F

00

00h

90h

POWER ON/OFF

MAIN INPUT

ARC 

SCREEN MUTE

AUDIO MUTE

VOLUME 

CONTRAST

BRIGHTNESS

COLOR

TINT

SHARPNESS

OSD ON/OFF

CHILD LOCK

PIP MODE

PIP ARC

PIP POSITION

TREBLE

BASS

BALANCE

COLOR TEMP.

RED LEVEL

GREEN LEVEL

BLUE LEVEL

PIP INPUT

CURRENT STATE

Adjustment

CMD

SET ID VAL

Remark

KA(ka)

XB(xb)

KC(kc)

KD(kd)

KE(ke)

KF(kf)

KG(kg)

KH(kh)

KI(ki)

KJ(kj)

KK(kk)

KL(kl)

KM(km)

KN(kn)

KO(ko)

KQ(kq)

KR(kr)

KS(ks)

KT(kt)

KU(ku)

KV(kv)

KW(kw)

K$(k$)

XY(xy)

KZ(kz)

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~99

0~1

10~90

0~6

0~1

0~1

0~64

0~64

0~64

0~64

0~64

0~64

0~1

0~1

0~3

0~64

0~64

0~64

0~3

0~60

0~60

0~60

10~90

FF

0: OFF, 1:ON

RF(10), AV1~4(20,21,22,23),

SAV(30), COMP(40),

RGB(50 or 60), HDMI(90)

SPECTACLE, FULL, ORIGINAL

4:3, 16:9, 14:9, ZOOM

0: MUTE,  1: MUTE OFF

0: MUTE,  1: MUTE OFF

0:0,  64:100 (Hexadecimal)

0:0,  64:100 (Hexadecimal)

0:0,  64:100 (Hexadecimal)

0:0,  64:100 (Hexadecimal)

0:R50,  64:G50 (Hexadecimal)

0: 0, 64:100 (Hexadecimal)

0: OFF,  1: ON

0: LOCK, 1: OFF

PIP_OFF, PIP, DW1, DW2

NOT USED

NOT USED

0:0,  64:100

0:0,  64:100

0:L50,  64:R50

COOL, NORMAL, WARM, USER

0:-30,  60:30

0:-30,  60:30

0:-30,  60:30

RF(10), AV1~4(20,21,22,23),

SAV(30), COMP(41),

DVI(50 or 60), ,HDMI(61)

ACK : 0 - With signal

ACK : 1 -> Without signal

ACK : 2 -> Power Off