LG 32PC5RV-UG (CHASSIS:PP78C) Service Manual ▷ View online
- 5 -
ADJUSTMENT INSTRUCTIONS
1. Application Range
This spec sheet is applied all of the 32” PDP TV, PP78C
chassis .
chassis .
2. Specification
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument..
transformer will help protect test instrument..
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of
(3) The adjustment must be performed in the circumstance of
25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.
there is no specific designation.
(4) The input voltage of the receiver must keep 100~220V,
50/60Hz
(5) Before adjustment, execute Heat-Run for 30 minutes.
3. Download Program Installation
(1) Extract a Zip file
(2) Visaul I2C & LPT Driver Installation
(3) Verification (Start>Programs>Micronas>Visual I2C or
LptDrv)
(4) LPT delay setting (File>Preference>LPT preferences..)
(5) Exchange the bootloader.bat file
Install the LPT Driver
Install the Visual I2C
Install the Visual I2C
G
LPT SETTING
- Delay -> 1
- Timeout -> 500 ms
- Timeout -> 500 ms
- 6 -
G
Select the "Bootloader.bat" file.
(install > VCTP_download > Bootloader)
G
Push "OK".
G
Finish the program, after saving the file
"download_cs.vi2
c
".
4. S/W Program Download
4-1. Download Method 1 (PCB Ass’y)
(1) Connect the download jig to D-sub jack.
(2) Execute ‘Download.vi2c’ program in PC, then a main
(2) Execute ‘Download.vi2c’ program in PC, then a main
window will be opened
(3) Double click the red box and confirm “Bootloader Version”
as 42.
(4) Click the “Erase Flash” button
(5) Double click the download file low, then “edit” window will
be opened
(6) Click the choice button in the “edit window”, then “file
choice window” will be opened
ADJUSTMENT INSTRUCTIONS
- 7 -
(7) Choose the Hex file in folder and execute downloading
with click “ open” button.
(8) Click OK button at the “edit window”
(9) Under Downloading process
(10) If download is failed, for example “No acknowledge from
slave”. Execute download again from(1)
4-2. Download Method 2 (SET)
(1) Push the “Tilt” button in an Adjust Remocon Then the PDP
will change a “slave mode”
(2) Connect Zig to TV using a D-sub cable
(3) Execute ‘Download_CS.vi2c’ program in PC, then a main
widow will be opened.
(4) Click “GO” button
If you don’t push the “go”, the Hex file would not be
downloaded although the download proceeds normally at
first glance
downloaded although the download proceeds normally at
first glance
(5) Double click the blue box and confirm “Bootloader Version”
as 42.
ADJUSTMENT INSTRUCTIONS
slave mode
- 8 -
(6) Click the “Erase Flash” button
(7) Double click the download file low then, “edit” window will
be opened
(8) Chick the choice button In the “edit window”, then “file
choice window’ will be opened
(9) Choose the Hex file in folder and execute downloading
with click “open button”
(10) Click OK button at the “edit window”
(11) Under Downloading progress
(12) If download is failed, for example “No acknowledge from
slave”, execute download again from (1)
ADJUSTMENT INSTRUCTIONS
Click on the first or last page to see other 32PC5RV-UG (CHASSIS:PP78C) service manuals if exist.