LG 32LT560H-SA (CHASSIS:LJ2AW) Service Manual ▷ View online
- 9 -
3.1. ADC Process(TBD)
3.1.1. ADC
■ Enter Service Mode by pushing “ADJ” key,
Calibration”
=> Caution : Using ‘power on’ button of the Adjustment R/C,
power on TV.
※
ADC Calibration Protocol (RS232C/USB)
NO
Item
CMD 1 CMD 2 Data 0
Enter
Adjust MODE
Adjust
‘Mode In’
A
A
0
0 When transfer the
‘Mode In’,
Carry the command.
ADC adjust
ADC
Adjust
A
D
1
0 Automatically adjust-
ment
(The use of a inter-
nal pattern)
※
Adjust Sequence
▪ aa 00 00 [Enter Adjust Mode]
▪ xb 00 40 [Component1 Input (480i)]
▪ ad 00 10 [Adjust 480i Comp1]
▪ xb 00 60 [RGB Input (1024*768)]
▪ ad 00 10 [Adjust 1024*768 RGB]
▪ aa 00 90 End Adjust mode
* Required equipment : Adjustment R/C.
3.2. Function Check
3.2.1. Check display and sound
■ Check Input and Signal items. (cf. work instructions)
(1) TV
(2) AV (CVBS)
(3) COMPONENT (480i)
(4) RGB (PC : 1024 x 768 @ 60hz)
(5) HDMI
(6) PC Audio In
* Display and Sound check is executed by Remote controller.
※
※
Caution : Not to push the INSTOP KEY after completion if
the function inspection
4. Total Assembly line process
4.1. Adjustment Preparation
■ W/B Equipment condition
CA210 : CH 9, Test signal : Inner pattern (80IRE) – in case of
CCFL back light
CA210 : CH14, Test signal : Inner pattern (80IRE) – in case of
LED back light
■ Above 5 minutes H/run in the inner pattern. (“power on” key of
adjust remote control)
※
LCD LAMP MODEL : The spec of color temperature and
coordinate
19” and 22”
Cool (C50)
9,300K
x = 0.285 (±0.002)
y = 0.293 (±0.002)
<Test signal>
- Inner pattern for W/B
adjust
- External white
pattern
(80IRE, 204gray)
Medium (0)
8,000K
x = 0.295 (±0.002)
y = 0.305 (±0.002)
Warm (W50)
6,500K
x = 0.313 (±0.002)
y = 0.329 (±0.002)
Over 26”
Cool (C50)
13,000K x = 0.269 (±0.002)
y = 0.273 (±0.002)
<Test signal>
- Inner pattern for W/B
adjust
- External white
pattern
(80IRE, 204gray)
Medium (0)
9,300K
x = 0.285 (±0.002)
y = 0.293 (±0.002)
Warm (W50)
6,500K
x = 0.313 (±0.002)
y = 0.329 (±0.002)
※
LED Model : W/B adjust target value
Cool
Medium
Warm
Remark
X
y
x
y
x
y
SPEC
269 273 285 293 313 329 ALL LED Model
26/32/42LT360C
32/37/42LT560H
TARGET 271 276 287 296 315 332
- 10 -
※
Connecting picture of the measuring instrument
(On Automatic control)
Inside PATTERN is used when W/B is controlled. Connect to
auto controller or push Adjustment R/C POWER-ON -> Enter
the mode of White-Balance, the pattern will come out.
●
Auto-control interface and directions
(1) Adjust in the place where the influx of light like floodlight
around is blocked. (Illumination is less than 10ux).
(2) Adhere closely the Color Analyzer ( CA210 ) to the module
less than 10cm distance, keep it with the surface of the
Module and Color Analyzer’s Prove vertically.(80~100°).
(3) Aging time
- After aging start, keep the power on (no suspension of
power supply) and heat-run over 5 minutes.
- Using ‘no signal’ or ‘full white pattern’ or the others, check
the back light on.
● Auto adjustment Map(RS-232C)
RS-232C COMMAND
[ CMD ID DATA ]
Wb 00 00 White Balance Start
Wb 00 ff White Balance End
RS-232C COMMAND
[CMD ID DATA]
MIN
CENTER
(DEFAULT)
MAX
Cool
Mid
Warm
Cool
Mid
Warm
R Gain
jg
Ja
jd
00
172
192
192
192
G Gain
jh
Jb
je
00
172
192
192
192
B Gain
ji
Jc
jf
00
192
192
172
192
R Cut
64
64
64
128
G Cut
64
64
64
128
B Cut
64
64
64
128
** Caution **
Color Temperature : COOL, Medium, Warm.
One of R Gain/G Gain/ B Gain should be kept on 0xC0, and
adjust other two lower than C0.
(when R/G/B Gain are all C0, it is the FULL Dynamic Range of
Module)
*Manual W/B process using adjusts Remote control.
■After enter Service Mode by pushing “ADJ” key,
■Enter White Balance by pushing “►” key at “7. White Balance”.
※
After You finish all adjustments, Press “In-start” button and
compare Tool option and Area option value with its BOM, if it is
correctly same then unplug the AC cable.
If it is not same, then correct it same with BOM and unplug AC
cable. For correct it to the model’s module from factory JIG
model.
※
Push The “IN STOP KEY” after completing the function
inspection. And Mechanical Power Switch must be set “ON”.
- 11 -
4.2. DDC EDID Write (RGB 128Byte)
■ Connect D-sub Signal Cable to D-Sub Jack.
■ Write EDID DATA to EEPROM (24C02) by using DDC2B
protocol.
■ Check whether written EDID data is correct or not.
* For SVC main Ass’y, EDID have to be downloaded to Insert
Process in advance.
4.3. DDC EDID Write (HDMI 256Byte)
■ Connect HDMI Signal Cable to HDMI Jack.
■ Write EDID DATA to EEPROM(24C02) by using DDC2B
protocol.
■ Check whether written EDID data is correct or not.
* For SVC main Ass’y, EDID have to be downloaded to Insert
Process in advance.
4.4. EDID DATA
1) All Data : HEXA Value
2) Changeable Data :
*: Serial No : Controlled / Data:01
**: Month : Controlled / Data:00
***:Year : Controlled
****:Check sum
- Auto Download
■ After enter Service Mode by pushing “ADJ” key,
■ Enter EDID D/L mode.
■ Enter “START” by pushing “OK” key.
※
Edid data and Model option download (RS232C)
NO
Item
CMD 1 CMD 2
Data 0
Enter
download
MODE
Download
‘Mode In’
A
A
0
0
When transfer
the ‘Mode In’,
Carry the com-
mand
Edid data
and Model
option
download
Download
A
E
00
10
Automatically
download
(The use of a
internal Data)
※
Caution
* Use the proper signal cable for EDID Download
- Analog EDID : Pin3 exists
- Digital EDID : Pin3 exists
=> Caution
- Never connect HDMI & D-sub Cable at the same time.
- Use the proper cables below for EDID Writing.
- Download HDMI1, HDMI2 separately because HDMI1 is
different from HDMI2.
For Analog EDID
For HDMI EDID
D-sub to D-sub
DVI-D to HDMI or HDMI to HDMI
No.
Item
Condition
Hex Data
1
Manufacturer ID
GSM
1E6D
2
Version
Digital : 1
01
3
Revision
Digital : 3
03
●
EDID DATA
(1) HD EDID Data
CheckSum
Physical Address (0x9E)
HDMI 1
A4/5B
10
HDMI 2
A4/4B
20
- 12 -
(2) FHD EDID Data(Deep Color support)
CheckSum
Physical Address (0x9E)
HDMI 1
43/DE
10
HDMI 2
43/CE
20
HDMI 3
43/BE
30
- HDMI
-RGB
(3) FHD EDID Data(Deep Color not support)
CheckSum
Physical Address (0x9E)
HDMI 1
43/25
10
HDMI 2
43/15
20
HDMI 3
43/05
30
- HDMI
-RGB
- Model List
HD(LED)
FHD(LED)
26LT360C-SA
37LT560H-SA
32LT360C-SA
42LT360C-SA
32LT560H-SA
42LT560H-SA
Click on the first or last page to see other 32LT560H-SA (CHASSIS:LJ2AW) service manuals if exist.