LG 32LN520B (CHASSIS:LT36B) Service Manual ▷ View online
- 13 -
*Manual W/B process using adjusts Remote control.(TBD)
■ Color analyzer(CA100+, CA210) should be used in the
calibrated ch by CS-1000
■ Operate the zero-calibration of the CA100+ or CA-210, then
stick sensor to the module when adjusting.
■ After enter Service Mode by pushing “ADJ” key,
■Enter White Balance by pushing “►” key at “8. White Balance”.
■ For manual adjustment, it is also possible by the following
sequence.
(1) Set TV in Adj. mode using POWER ON
(2) Zero Calibrate the probe of Color Analyzer, then place it on
the center of LCD module within 10cm of the surface
(3) Press ADJ key -> EZ adjust using adj. R/C -> 8. White-
Balance then press the cursor to the right (KEY►). When
KEY(►) is pressed 206 Gray internal pattern will be displayed.
(4) Adjust Cool modes
(i). Fix the one of R/G/B gain to 192 (default data) and decrease
the others
(If G gain is adjusted over 172 and R and B gain less than
192, increase G gain to 192 and increase R gain and B gain
same amount of increasing G gain.)
(ii). If G gain is less than 172,
Increase G gain by up to 172, and then increase R gain and
G gain same amount of increasing G gain.
(iii). If R gain or B gain is over 255,
Readjust G gain less than 172, Conform to R gain is 255 or B
gain is 255
(5) Adjust two modes (Medium / Warm) Fix the one of R/G/B gain
to 192 (default data) and decrease the others.
(6) Adj. is completed, Exit adjust mode using “EXIT” key on
Remote controller.
▪ If internal pattern is not available, use RF input. In EZ Adj. menu
8. White Balance, you can select one of 2 Test-pattern: ON,
OFF. Default is inner (ON). By selecting OFF, you can adjust
using RF signal in 206 Gray pattern.
※
CASE Cool
First adjust the coordinate far away from the target value(x, y).
(1) x, y > target
i) Decrease the R, G.
(2) x, y < target
i) First decrease the B gain,
ii) Decrease the one of the others.
(3) x > target , y< target
i) First decrease B, so make y a little more than the target.
ii) Adjust x value by decreasing the R
(4) x < target , y >target
i) First decrease B, so make x a little more than the target.
ii) Adjust x value by decreasing the G
How to adjust
(1) If G gain is adjusted over 172 and R gain and B gain less
than 192 , Adjust is O.K.
(2) If G gain is less than 172 , increase G gain by up to 172,
and then increase R gain and B gain same amount of increasing
G gain.
(3) If R gain or B gain is over 255 , Readjust G gain less than
172, Conform to R gain is 255 or B gain is 255
※
CASE Medium / Warm
First adjust the coordinate far away from the target value(x, y).
(1) x, y > target
i) Decrease the R, G.
(2) x, y < target
i) First decrease the B gain,
ii) Decrease the one of the others.
(3) x > target , y< target
i) First decrease B, so make y a little more than the target.
ii) Adjust x value by decreasing the R
(4) x < target , y >target
i) First decrease B, so make x a little more than the target.
ii) Adjust x value by decreasing the G
▪ After You finish all adjustments, Press “In-start” button and
compare Tool option and Area option value with its BOM, if it is
correctly same then unplug the AC cable. If it is not same, then
correct it same with BOM and unplug AC cable. For correct it to
the model’s module from factory JIG model.
▪ Push the “IN STOP KEY” after completing the function
inspection.
- 14 -
4.2. DPM operation confirmation
(Only Apply for MNT Model)
Check if Power LED Color and Power Consumption operate
as standard.
■ Set Input to RGB and connect D-sub cable to set
■ Measurement Condition: (100~240V@ 50/60Hz)
■ Confirm DPM operation at the state of screen without Signal
4.3. DDC EDID Write (HDMI 256Byte)
■ Connect HDMI Signal Cable to HDMI Jack.
■ Write EDID DATA to EEPROM(24C02) by using DDC2B
protocol.
■ Check whether written EDID data is correct or not.
* For SVC Ass’y, EDID have to be downloaded.
4.4. EDID DATA
1) All Data : HEXA Value
2) Changeable Data :
*: Serial No : Controlled / Data:01
**: Month : Controlled / Data:00
***:Year : Controlled
****:Check sum
- Auto Download
■ After enter Service Mode by pushing “ADJ” key,
■ Enter EDID D/L mode.
■ Enter “START” by pushing “OK” key.
※
Edid data and Model option download (RS232C)
NO
Item
CMD 1 CMD 2
Data 0
Enter
download
MODE
Download
‘Mode In’
A
A
0
0
When transfer
the ‘Mode In’,
Carry the com-
mand
Edid data
and Model
option
download
Download
A
E
00
10
Automatically
download
(The use of a
internal Data)
※
Caution
* Use the proper signal cable for EDID Download
- Analog EDID : Pin3 exists
- Digital EDID : Pin3 exists
=> Caution
- Never connect HDMI & D-sub Cable at the same time.
- Use the proper cables below for EDID Writing.
- Download HDMI1, HDMI2 separately because HDMI1 is
different from HDMI2.
For Analog EDID
For HDMI EDID
D-sub to D-sub
DVI-D to HDMI or HDMI to HDMI
No.
Item
Condition
Hex Data
1
Manufacturer ID
GSM
1E6D
2
Version
Digital : 1
01
3
Revision
Digital : 3
03
●
EDID DATA
(1) HD 2D EDID Data
CheckSum
Physical Address (0x9E)
HDMI 1
A3/5B
10
HDMI 2
A3/4B
20
- 15 -
(2) FHD 2D EDID Data (Support Deep Color – 10bit)
CheckSum
Physical Address (0x9E)
HDMI 1
42/DE
10
HDMI 2
42/CE
20
(3) FHD 2D EDID Data (Not Support Deep Color – 8bit)
CheckSum
Physical Address (0x9E)
HDMI 1
42/25
10
HDMI 2
42/15
20
(4) HD 3D EDID Data
CheckSum
Physical Address (0x9E)
HDMI 1
A3/59
10
HDMI 2
A3/49
20
- HDMI
(5) FHD 3D EDID Data (Not Support Deep Color – 8bit)
CheckSum
Physical Address (0x9E)
HDMI 1
42/23
10
HDMI 2
42/13
20
- HDMI
- 16 -
(6) FHD 3D EDID Data (Support Deep Color – 10bit)
CheckSum
Physical Address (0x9E)
HDMI 1
42/DC
10
HDMI 2
42/CC
20
(7) HD 3D DTS EDID Data
CheckSum
Physical Address (0x9E)
HDMI 1
A3/C0
10
HDMI 2
A3/B0
20
(8) FHD 3D DTS EDID Data (Not Support Deep Color – 8bit)
CheckSum
Physical Address (0x9E)
HDMI 1
42/8A
10
HDMI 2
42/7A
20
- HDMI
(9) HD 2D DTS EDID Data
CheckSum
Physical Address (0x9E)
HDMI 1
A3/C2
10
HDMI 2
A3/B2
20
- HDMI
Click on the first or last page to see other 32LN520B (CHASSIS:LT36B) service manuals if exist.