DOWNLOAD LG 32LG40 (CHASSIS:LA89A) Service Manual ↓ Size: 7.6 MB | Pages: 35 in PDF or view online for FREE

- 13 -

(3) Adjustment Map

(Automatic Adjustment)

1) The adjustment condition should be set by the Power On

key.

2) Perform the zero calibration of the Color Analyzer and

place the probe close to the display center.

3) Connect the communication cable (RS-232C).
4) Select the desired model of the adjustment program and

perform the adjustment.

5) After the adjustment is ended (check the OK sign), check

the adjustment condition for each mode of the set.
(Warm, Medium, Cool)

6) Disconnect the probe and the communication cable to end

the adjustment.

* The adjustment should be started with "wb 00 00" and

ended with "wb 00 ff", and the offset should be adjusted
when necessary.

1) The adjustment condition should be set by the Power On

key.

2) Press the ADJ of the R/C to enter into 'EZ-ADJUST'.
3) Select '10.TEST PATTERN' with the CH +/- key and press

the Enter key for 30 minutes or longer to perform the heat
run.

4) Perform the zero calibration of the Color Analyzer and fix

the sensor with the 10cm or less distance at the center of
the LCD module surface when adjusting.

5) Press the ADJ of the R/C to select '7.White-Balance' of the

Ez-Adjust and press the right arrow key(

G

) to enter into the

adjustment mode. (As soon as you press '

G

', the screen is

entered into the full white inner pattern.)

6) Fix one of the R/G/B gains to 192 and decrease the

remaining two gains to adjust not to exceed 192.

7) The adjustment is done at three white balances of Cool,

Medium and Warm.

* The inner pattern is used basically, and if it is not possible,

the adjustment can be done by selecting the HDMI input.
NONE, INNER or HDMI can be selected by the bottom
option at the Ez Adjust Menu 7.White Balance menu and it is
set to INNER as default. If the adjustment cannot be done by
the inner pattern, select the HDMI to adjust.

* Adjustment environment and reference

1) Environment illuminance

Adjust it to 10 LUX or less at the place where the light
source such as lamp should be blocked at maximum.

2) Probe location

: Maintain the Color Analyzer (CA-210) close to the

module surface by 10cm or less and keep the probe of
the Color Analyzer perpendicular to the module
surface (80°~ 100°).

3) Aging time

- Keep the power on after the aging start (with no power

off) to perform the heat run for 15 minutes or longer.

- Make sure that the back light is turned on by using no

signal and the full white pattern or others.

(1) Brightness : Full white 216 Gray 
(2) Standard color coordinate and white balance when using

the CS-1000

(3) Standard color coordinate and white balance when using

the CA-210 (CH 10)

model only, which selects the rating related country.

2) Applied models: LA89A Chassis applied None USA

Model(Canada, Mexico)

1) Press the In-Start key of the R/C and press the red oval

OP1(PIP CH-) key to enter into the Factory Option menu.

2) Select 1.USA, 2.CANADA or 3.MEXICO from the country

select according to the destination. At this time, use the
volume +/- key to adjust 

ITEM

Command

Data Range

Default

(Hex.)

(Decimal)

Cmd 1

Cmd 2

Min

Max

Cool

R-Gain

j

g

00

C0

TBD

G-Gain

j

h

00

C0

TBD

B-Gain

j

i

00

C0

TBD

R-Cut

TBD

G-Cut

TBD

B-Cut

TBD

Medium

R-Gain

j

a

00

C0

TBD

G-Gain

j

b

00

C0

TBD

B-Gain

j

c

00

C0

TBD

R-Cut

TBD

G-Cut

TBD

B-Cut

TBD

Warm

R-Gain

j

d

00

C0

TBD

G-Gain

j

e

00

C0

TBD

B-Gain

j

f

00

C0

TBD

R-Cut

TBD

G-Cut

TBD

Mode

Color Coordination

Temp

∆UV

x

y

COOL

0.276

0.283

11000K

0.0000

MEDIUM

0.285

0.293

9300K

0.0000

WARM

0.313

0.324

6500K

0.0000

Mode

Color Coordination

Temp

∆UV

x

y

COOL

0.276±0.002

0.283±0.002

11000K

0.0000

MEDIUM

0.285±0.002

0.293±0.002

9300K

0.0000

WARM

0.313+0.002

0.324±0.002

6500K

0.0000

- After completing the final test, in order to set the set to the

shipping condition, press the In-Stop key of the R/C to make
sure that the set is turned off.

(1) Preparing for the automatic test on the GND & resisting

pressure 

- Make sure that the power cord is inserted into the set

completely. (When it is disconnected or loosened, test
after inserting it)

(2) Perform the automatic test on the GND & resisting pressure

1) The set with power cord, the cord and the A/V

completely inserted into the tuner is loaded on the pallet
and entered into the automatic test process.

2) Connect the D-terminal AV JACK tester
3) Turn on the automatic (GWS103-4)
4) Perform the GND TEST
5) If it is not good, the buzzer is operated to notify the test

result to the operator.

6) If it is OK, it is automatically switched to the resisting

pressure test. (Disconnect the cord and the A/V from the
AV JACK BOX)

6) Perform the resisting pressure test
7) If it is not good, the buzzer is operated to notify the test

result to the operator.

8) If it is OK, the GOOD LAMP is turned and the stopper is

moves down, and it moves to the next process.

(1) TEST voltage

- GND : 1.5KV/min at 100mA
- SIGNAL : 3KV/min at 100mA

(2) TEST time:1 second
(3) TEST POINT

- GND test = between Power cord GND and Signal cable

metal GND

- Resisting pressure test = between Power cord GND and

Live & Neutral

(4) LEAKAGE CURRENT: Set to 0.5mArms 

The Micom upgrade via the external port for the service for
the customer.

1) PC
2) B/D for the interface (IIC & ISP)
3) Jig for downloading (for the power supply)

1) IC name & circuit number: MYSON MTV416GMF & IC4015
2) Power supply: 5V (P4004 Pin 3)
3) SCL: D-sub Pin 10
4) SDA: D-sub Pin  7

1) After executing LGE Monitor Tools v1.1, click the first icon.

(See the figure)

2) When the screen is displayed as shown at the below figure,

set the items as follows:

- MCU Select: MTV512M64
- R/W Option: Auto Write(Verify)
- Jig Option: Myson
- Transmit Speed: Medium
- Check: blank
- PORT: Select the Parallel Port to use (LPT1 in general)
* caution: Select the EPP as LPT from the ROM BIAS

setting.

3) Click the Load File Button, and select the desired Hex File

to download. (If no file is displayed, make sure that the file
format is selected as Hex file (*.hex))

- 14 -

Interface B/D

Main B/D

PC

Pin301

4) Click 'Send Button

The USB download is for the quick service response via the
S/W upgrade and for applying the S/W upgrade necessary for
the board adjustment

1) After turning on the set, make sure that the display screen

is turned on.

2) When the USB Memory Stick with the upgrade file applied

is inserted into the USB jack on the main board, the
following screen (example) is displayed after several
seconds

3) Check the current version at [Current TV Software Version

Information], check the S/W version to upgrade at [New
Found TV Software Version Information], and press the
Enter button of the TV remote controller.

4) Downloading is proceeded as shown at the below screen,

and when it is ended, turning on/off is automatically done.

(When the automatic proceeding is not smoothly done,
manually perform the power On/Off).

5) When downloading is ended, remove the USB Memory

Stick from the USB jack.

6) Press the IN-START button of the remote controller to

check the upgraded S/W version.

- 15 -

   

Do not plug off.

Press EXIT to cancel the upgrade.

   

Do not plug off.

Press EXIT to cancel the upgrade.

- 16 -

Check TU800 Pin 16 (Video output).

Can you see the normal signal?

Check the input (Pin 1) of LPF(IC800).

Can you  see the normal waveform?

Could you measure voltage of TU800 &

IIC lines? Are they all normal?

You should replace TUNER.

Yes

No

Yes

Yes

Check the input (PinAN16) of BCM355x

(IC100). Measure waveform at C658

because it;s more easy to check.

Can you see the normal waveform?

You should check power line

& IIC lines

No

After checking video signal line & the Power of

LPF you should decide to  replace item or not.

No

Check the output (Pin 8) of LPF(IC800).

Can you  see the normal waveform?

Yes

Yes

After checking Power of LPF you should decide

to replace item or not.

No

This board has big problem because Main chip

(BCM355x) have some troubles.

After checking thoroughly all path once again,

You should decide to replace BCM355x or not.

No

Check JK701, JK706.

Can you see the normal waveform?

Check the input (PinAN17, AM19) of

BCM355x (IC100). Measure waveform at

C651 because it’s more easy to check.

Can you see the normal waveform?

JK701, JK706 may have problem.

Replace this Jack.

No

This board has big problem because Main chip

(BCM355x) have some troubles.

After checking thoroughly all path once again,

You should decide to replace BCM355x or not.

No