DOWNLOAD LG 32LG30 (CHASSIS:LA85D) Service Manual ↓ Size: 5.87 MB | Pages: 35 in PDF or view online for FREE

Model
32LG30 (CHASSIS:LA85D)
Pages
35
Size
5.87 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / LCD
File
32lg30-chassis-la85d.pdf
Date

LG 32LG30 (CHASSIS:LA85D) Service Manual ▷ View online

- 5 -
IC Remove/Replacement
Some chassis circuit boards have slotted holes (oblong) through
which the IC leads are inserted and then bent flat against the
circuit foil. When holes are the slotted type, the following technique
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique
as outlined in paragraphs 5 and 6 above.
Removal
1.  Desolder and straighten each IC lead in one operation by gently
prying up on the lead with the soldering iron tip as the solder
melts.
2.  Draw away the melted solder with an anti-static suction-type
solder removal device (or with solder braid) before removing the
IC.
Replacement
1.  Carefully insert the replacement IC in the circuit board.
2.  Carefully bend each IC lead against the circuit foil pad and
solder it.
3.  Clean the soldered areas with a small wire-bristle brush.
(It is not necessary to reapply acrylic coating to the areas).
"Small-Signal" Discrete Transistor
Removal/Replacement
1.  Remove the defective transistor by clipping its leads as close as
possible to the component body.
2.  Bend into a "U" shape the end of each of three leads remaining
on the circuit board.
3.  Bend into a "U" shape the replacement transistor leads.
4.  Connect the replacement transistor leads to the corresponding
leads extending from the circuit board and crimp the "U" with
long nose pliers to insure metal to metal contact then solder
each connection.
Power Output, Transistor Device
Removal/Replacement
1.  Heat and remove all solder from around the transistor leads.
2. Remove the heat sink mounting screw (if so equipped).
3.  Carefully remove the transistor from the heat sink of the circuit
board.
4.  Insert new transistor in the circuit board.
5. Solder each transistor lead, and clip off excess lead.
6.  Replace heat sink.
Diode Removal/Replacement
1.  Remove defective diode by clipping its leads as close as
possible to diode body.
2.  Bend the two remaining leads perpendicular y to the circuit
board.
3.  Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4.  Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.
Fuse and Conventional Resistor
Removal/Replacement
1.  Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2.  Securely crimp the leads of replacement component around
notch at stake top.
3.  Solder the connections.
CAUTION: Maintain original spacing between the replaced
component and adjacent components and the circuit board to
prevent excessive component temperatures.
Circuit Board Foil Repair
Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
board causing the foil to separate from or "lift-off" the board. The
following guidelines and procedures should be followed whenever
this condition is encountered.
At IC Connections
To repair a defective copper pattern at IC connections use the
following procedure to install a jumper wire on the copper pattern
side of the circuit board. (Use this technique only on IC
connections).
1.  Carefully remove the damaged copper pattern with a sharp
knife. (Remove only as much copper as absolutely necessary).
2.  carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.
3.  Bend a small "U" in one end of a small gauge jumper wire and
carefully crimp it around the IC pin. Solder the IC connection.
4.  Route the jumper wire along the path of the out-away copper
pattern and let it overlap the previously scraped end of the good
copper pattern. Solder the overlapped area and clip off any
excess jumper wire.
At Other Connections
Use the following technique to repair the defective copper pattern
at connections other than IC Pins. This technique involves the
installation of a jumper wire on the component side of the circuit
board.
1.  Remove the defective copper pattern with a sharp knife.
Remove at least 1/4 inch of copper, to ensure that a hazardous
condition will not exist if the jumper wire opens.
2.  Trace along the copper pattern from both sides of the pattern
break and locate the nearest component that is directly
connected to the affected copper pattern.
3.  Connect insulated 20-gauge jumper wire from the lead of the
nearest component on one side of the pattern break to the lead
of the nearest component on the other side.
Carefully crimp and solder the connections.
CAUTION: Be sure the insulated jumper wire is dressed so the
it does not touch components or sharp edges.
- 6 -
4. General Specification(TV) 
No.
Item
Specification Remark 
1. 
Receiving System 
ATSC/ NTSC-M
2.
Available Channel
1) VHF : 02~13
2) UHF : 14~69
3) DTV : 02-69
4) CATV : 01~135
5) CADTV : 01~135
3.
Input Voltage
1) 100- 240V~, 50/60Hz
Mark : 110V, 60Hz
4.
Market
NORTH AMERICA
5.
Screen Size
32 inch Wide (1366 x 768)
HD
6.
Aspect Ratio
16:9
7.
Tuning System
FS
8.
LCD Module
LK315T3LZ94
SHARP
9.
Operating Environment
1) Temp   :  0 ~ 40 deg
2) Humidity :   ~ 80 %
10.
Storage Environment
1) Temp    : -20 ~ 60 deg
2) Humidity : 0 ~ 85 %
1. Application Range
This spec sheet is applied to the LCD TV used LA85D
chassis.
2. Specification
Each part is tested as below without special appointment  
1) Temperature :  25 ± 5°C (77 ± 9ºF), CST : 40 ± 5ºC
2) Relative Humidity : 65 ±10% 
3) Power Voltage :  Standard input voltage
(100-240V@ 50/60Hz)
* Standard Voltage of each products is marked by models 
4) Specification and performance of each parts are followed
each drawing and specification by part number in
accordance with BOM.
5) The receiver must be operated for about 20 minutes prior to
the adjustment.
3. Test method
1) Performance : LGE TV test method followed.
2) Demanded other specification 
- Safety : UL1492, CSA C22.2 No.1
- EMC : FCC Class B, IC Class B
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
- 7 -
5. Chroma & Brightness
No
Item
Min.
Typ.
Max.
Unit
Remark
1
White peak brightness
350
450
cd/m
2
(Center 1-point / Full White Pattern)
2
White average brightness
cd/m
2
N/A
3
Brightness uniformity
80
%
Full white
4
Color coordinate
RED
X
0.640
± 0.03
Y
0.330
± 0.03
GREEN
X
0.280
± 0.03
Y
0.600
± 0.03
BLUE
X
0.150
± 0.03
Y
0.060
± 0.03
WHITE
X
0.272
± 0.03
Y
0.277
± 0.03
5
Color coordinate uniformity
N/A
6
Contrast ratio
1000:1
1500:1
32LG30-UD
10000:1
DCR
7
Color Temperature
Cool
10,000
11,000
12,000
<Test Signal>
Standard
8,300
9,300
10,300
HDMI input
Warm
5,500
6,500
7,500
85% Full white pattern
8
Color Distortion, DG
10.0
%
9
Color Distortion, DP 
10.0
deg
10
Color S/N, AM/FM
43.0
dB
11
Color Killer Sensitivity
-80
dBm
6.  Component Video Input  (Y, C
B
/P
B
, C
R
/P
R
)  
No.
Specification            
Remark
Resolution H-freq(kHz)
V-freq(Hz)
Pixel 
clock
1. 
720*480
15.73
60
13.5135
SDTV ,DVD 480I
2. 
720*480
15.73
59.94
13.5
SDTV ,DVD 480I
3. 720*480
31.47
60
27.027
SDTV 
480P
4. 720*480
31.47
59.94
27.0
SDTV 
480P
5. 1280*720
45.00
60.00
74.25
HDTV 
720P
6. 1280*720
44.96
59.94
74.176
HDTV 
720P
7. 1920*1080
33.75
60.00
74.25
HDTV 
1080I
8. 1920*1080
33.72
59.94
74.176
HDTV 
1080I
9. 1920*1080
67.500
60
148.50
HDTV 
1080P
10. 1920*1080
67.432
59.939
148.352
HDTV 
1080P
11. 1920*1080
27.000
24.000
74.25
HDTV 
1080P
12. 1920*1080
26.97
23.976
74.176
HDTV 
1080P
13. 1920*1080
33.75
30.000
74.25
HDTV 
1080P
14. 1920*1080
33.71
29.97
74.176
HDTV 
1080P
- 8 -
No. Specification 
Remark 
Resolution H-freq(kHz) 
V-freq(Hz)
Pixel 
clock(MHz)
PC
DDC
1
640*350
31.469
70.08
25.17
DOS
2
720*400
31.469
70.08
28.32
DOS
O
3
640*480
31.469
59.94
25.17
VESA(VGA)
O
4
800*600
37.879
60.31
40.00
VESA(SVGA)
O
5
1024*768
48.363
60.00
65.00
VESA(XGA)
O
6
1280*768
47.776
59.87
79.50
CVT(WXGA)
O
7
1360*768
47.720
59.799
84.75
CVT(WXGA)
O
8
1366*768
47.13
59.65
72
7. RGB input (PC)
8. HDMI input (PC/DTV)
No. Resolution
H-freq(kHz)  V-freq(Hz)
Pixel 
clock(MHz)
Remark
PC
DDC
1. 640*480
31.469
59.94
25.17
VESA(VGA)
O
2. 800*600
37.879
60.31
40.00
VESA(SVGA)
O
3. 1024*768
48.363
60.00
65.00
VESA(XGA)
O
4. 1280*768
47.776
59.87
79.50
CVT(WXGA)
O
5. 1360*768
47.720
59.799
84.75
CVT(WXGA)
O
6. 1366*768
47.13
59.65
72
DTV
1
720*480
31.47
60
27.027
SDTV 480P
2
720*480
31.47
59.94
27.00
SDTV 480P
3
1280*720
45.00
60.00
74.25
HDTV 720P
4
1280*720
44.96
59.94
74.176
HDTV 720P
5
1920*1080
33.75
60.00
74.25
HDTV 1080I
6
1920*1080
33.72
59.94
74.176
HDTV 1080I
7
1920*1080
67.500
60
148.50
HDTV 1080P
8
1920*1080
67.432
59.939
148.352
HDTV 1080P
9
1920*1080
27.000
24.000
74.25
HDTV 1080P
10
1920*1080
26.97
23.976
74.176
HDTV 1080P
11
1920*1080
33.75
30.000
74.25
HDTV 1080P
12
1920*1080
33.71
29.97
74.176
HDTV 1080P
Page of 35
Display

Click on the first or last page to see other 32LG30 (CHASSIS:LA85D) service manuals if exist.