LG 32LD450C (CHASSIS:LC01B) Service Manual ▷ View online
4.5. V-COM Adjust
(Only M+S models which use LGD module)
- Why need Vcom adjustment?
- Why need Vcom adjustment?
A
The Vcom (Common Voltage) is a Reference Voltage of
Liquid Crystal Driving.
Liquid Crystal Driving.
-> Liquid Crystal need for Polarity Change with every frame.
- Adjust sequence (Method 1)
· Push ‘PIP’ key.
· If there is no flicker at default value, turn down or turn up
· If there is no flicker at default value, turn down or turn up
until no flicker, push ‘OK’ key to store.
· Push ‘Exit’ key to exit.
- Adjust sequence (Method 2)
· Enter ‘EZ ADJUST’ mode by pushing “ADJ” key.
· Select and enter ‘12. V-Com’ mode.
· If there is no flicker at default value, turn down or turn up
· Select and enter ‘12. V-Com’ mode.
· If there is no flicker at default value, turn down or turn up
until no flicker, push ‘OK’ key to store.
· Push ‘Exit’ key to exit.
4.6. Outgoing condition Configuration
- Push ‘IN-STOP’ key, the in-stop processing will start.
If processing i complete, TV will turn off automatically.
(Must not AC power OFF during blinking)
(Must not AC power OFF during blinking)
Confirm whether is normal or not when between power
board's ac block and GND is impacted on 1.5kV(dc) or
2.2kV(dc) for one second.
board's ac block and GND is impacted on 1.5kV(dc) or
2.2kV(dc) for one second.
- 13 -
V-Com
V-Com
425
EZ ADJUST
0. Tool Option1
1. Tool Option2
2. Tool Option3
3. Tool Option4
4. Tool Option5
5. Country Group
6. ADC Calibration
7. White Balance
8. 10 Point WB
9. Test Pattern
10. EDID D/L
11. Sub B/C
11. Sub B/C
12. V-Com
13. P-Gamma
Press ( ) to save.
Row Li ne
Column Line
C
LC
C
ST
Pane l
S
Y
S
T
E
M
Gat
e
Driv
e
IC
So urce D r i v e I C
Circuit Block
Ti m i n g
Co nt r o ll e r
Co nt r o ll e r
Po w e r
Blo ck
Blo ck
V
COM
Ga mma
Re f e r e nce V o ltage
Re f e r e nce V o ltage
Gamm a Reference
Volta ge
Volta ge
Data (R ,G,B ) & C ont ro l s ignal
Con t rol si gnal
Data (R ,G,B ) &
Con t rol si gnal
Con t rol si gnal
In
te
te
rf
a
c
e
TFT
Po w e r I n p u t
Power Input
Da t a I n p u t
Da t a I n p u t
V
COM
Liquid
Crys tal
Crys tal
V
COM
Model
V-COM default
32LD450C-CA
417
- 14 -
BLOCK DIAGRAM
1. INPUT
...
...
- 15 -
2. OUTPUT
...
...
...
’
- 16 -
LV
1
200
300
400
540
900
910
810
521
530
800
500
A10
A2
120
510
A4
550
* Set + Stand
* Stand base + body
EXPLODED VIEW
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
IMPORTANT SAFETY NOTICE
Click on the first or last page to see other 32LD450C (CHASSIS:LC01B) service manuals if exist.