DOWNLOAD LG 32LB9D (CHASSIS:LT73A) Service Manual ↓ Size: 6.66 MB | Pages: 33 in PDF or view online for FREE

- 13 -

5.1 Adjustment of RF / AV / S-VIDEO

* Required Equipments
8 Remote controller for adjustment.
8 MSPG-925FS Pattern Generator (Which has Video

Signal: 7 Color Bar Pattern shown in Fig. 1).

=>  Model: 207 / Pattern: 65  

5.1.1 Method of Auto RF / AV / S-VIDEO Color Balance

(NTSC-J).

1) Input the Video Signal: 7 Color Bar signal into AV1
2) Set the PSM to Dynamic mode in the Picture menu.

[Fig.1]

3) Press IN-START key on R/C for adjustment.

[Fig.2]

4) Press  the  G (Vol.+) key to operate the set, then it

becomes automatically.

5) Auto-RGB OK means the adjustment is completed.

5.2 Adjustment of Component
*Required Equipments
8 Remote controller for adjustment
8 MSPG-925FS Pattern Generator. (Which has 720p/60Hz

YPbPr output Pattern shown in Fig. 2)

=>  Model: 216 / Pattern: 65

5.2.1 Method of Auto Component Color Balance

1) Input the Component 720p/60Hz 7 Color Bar (MSPG-

925FS model:216, pattern:65) signal into Component.

2) Set the PSM to Dynamic mode in the Picture menu.

[Fig.1]

3) Press IN-START key on R/C for adjustment.
4) Press  the  G (Vol.+) key to operate the set, then it

becomes automatically.

5.3 Adjustment of RGB
*Required Equipments
8 Remote controller for adjustment
8 MSPG-925FS Pattern Generator

(Which has XGA [1024*768] 60Hz 8 color bar 100%
pattern shown in Fig. 3 )

5.3.1 Method of Auto RGB Color Balance

1) Input the PC 1024x768 @ 60Hz 7 Color Bar (MSPG-

925FS model:3, pattern:65)  signal into RGB. (using
D-sub to D-sub cable)

2) Set the PSM to Dynamic mode in Picture menu.
3) Press the IN-START key on R/C for adjustment.

[Fig.3]

4) Press  the  G (Vol.+) key operate To set , then it

becomes automatically.

5)  Auto-RGB OK means adjustment is completed

- 14 -

*Test Equipment
8 Color Analyzer (CA-210/CH.9)

=> When you adjust LCD color temperature, on Color

analyzer (CA-210), you should use Channel 9 which
is Matrix compensated (White, Red, Green, Blue
revised) by CS-1000 and adjust in accordance with
White balance adjustment coordinate which is
specified on the next..

* Color temperature standards according to CSM and Module 

CSM

Plasma

LCD

Cool

11,000k         11,000k

Medium

9,300k           9,300k

Warm

6,500k           6,500k

* White balance adjustment coordinate and color temperature

8 PC (for communication through RS-232C) => UART

Baud rate : 115200 bps

8 l Luminance Y AV : upper 200 cd/ß≥ (Typ : 350 cd/m

2

) =>

Applying to Cool

- Connecting picture of  the measuring instrument (On

Automatic control )

Inside PATTERN is used when W/B is controlled. Connect
to auto controller or push control R/C IN-START => Enter
the mode of White-Balance, the pattern will come out.

* Auto adjustment Map(RS-232C)

*Auto-control interface and directions

1 Adjust in the place where the influx of light like floodlight

around is blocked. (illumination is less than 10ux).

2.1 In case of PDP: Measure and adjust after sticking the Color

Analyzer (CA-100+, CA-210) to the side of the module.

2.2 In case of LCD: Adhere closely  the Color Analyzer (CA-210)

to the module less than 10cm distance, keep it with the
surface of the Module and Color Analyzer’s Prove
vertically.(80~100°).

2.3 Aging time  

- After aging start, keep the power on (no suspension of

power supply) and heat-run over 15 minutes.

- In case of PDP, keep white pattern using inside pattern.
- In case of LCD, using ‘no signal’ or ‘full white pattern’ or the

others, check the back light on

Communication

Type

LT73A

Protocol

Baud Rate

Data bit

Stop bit

Parity

115200

8

1

None

Protocol

Index

Cmd 1 Cmd 2 Data Min Value Max Value

Setting

R-Gain_Normal

j

a

00(00)

128(80)

G-Gain_Normal

j

b

00(00)

128(80)

B-Gain_Normal

j

c

00(00)

128(80)

R-Gain_Warm

j

d

00(00)

128(80)

G-Gain_Warm

j

e

00(00)

128(80)

B-Gain_Warm

j

f

00(00)

128(80)

R-Gain_Cool

j

g

00(00)

128(80)

G-Gain_Cool

j

h

00(00)

128(80)

B-Gain_Cool

j

i

00(00)

128(80)

R-Offset_Normal

l

j

00(00)

128(80)

G-Offset_Normal

l

k

00(00)

128(80)

B-Offset_Normal

l

l

00(00)

128(80)

R-Offset_Warm

l

m

00(00)

128(80)

Offset_Warm

l

n

00(00)

128(80)

B-Offset_Warm

l

o

00(00)

128(80)

R-Offset_Cool

l

p

00(00)

128(80)

G-Offset_Cool

l

q

00(00)

128(80)

B-Offset_Cool

l

r

00(00)

128(80)

Inside Pattern signal

w

b

00

W/B Adjust start

Inside Pattern signal

w

b

10

Inside Pattern

Inside Pattern signal

w

b

ff

W/B Adjust end

- 15 -

One of R Gain / G Gain / B Gain should be kept on 80, and
others  are controlled lowering from 80 

1) Press 'power on' of  the control R/C, set heat run to white by

pressing G, and heat run over 15 minutes 

(Set: RS-233 Host: PC, Baud Rate: 115200bps, Download:

Cortez).

2) Zero Calibrate CA-210, and when controlling, stick the sensor

to the center of LCD module surface.

3) Double click In-start key on Controlling R/C and get in ‘white

balance’.

4) Set test-pattern on and display inside pattern. Control is

carried out on three color temperature, COOL, MEDIUM,
WARM. (Control is carried out three times,)

5) When the R/G/B GAIN is 80 on OSD, it is the FULL DYNAMIC

Range of the Module. In order to control white balance without
the saturation of FULL DYNAMIC Range and DATA, one of R
Gain / G Gain / B Gain should be kept on 80, and other two is
controlled lowering from 80.

1. When R GAIN is set to 80

- Control G GAIN and B GAIN by lowering from 80. 

2. When B GAIN is set to 80

- Control R GAIN and G GAIN by lowering from 80.

3. When G GAIN is set to 80

- Control R GAIN and B GAIN by lowering from 80.

One of R Gain / G Gain / B Gain should be kept on 80, and
adjust other two lower than 80.
(When R/G/B GAIN are all 80, it is the FULL DYNAMIC

Range of Module) 

- 16 -