DOWNLOAD LG 32HIZ20 (CHASSIS:LP61D) Service Manual ↓ Size: 2.5 MB | Pages: 31 in PDF or view online for FREE

This spec sheet is applied all of the26/32" LCD TV, LP61D
chassis(HURRICANE 3 MIDDLE) by manufacturing LG TV
Plant all over the world.  

2.1 Because this is not a hot chassis, it is not necessary to

use an isolation transformer. However, the use of isolation
transformer will help protect test instrument.

2.2 Adjustment must be done in the correct order.
2.3 The adjustment must be performed in the circumstance of

25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.

2.4 The input voltage of the receiver must keep 100-220V~,

50/60Hz.

2.5 Before adjustment, execute Heat-Run for 30 minutes at

RF no signal.

* Caution : Each PCB assembly must be checked by check JIG

set. (Because power PCB Assembly damages to
LCD Module,especially be careful)

1) Adjusting PC with S/W for writing EDID Data.(S/W :

EDID TESTER Ver.2.5)

2) A Jig for EDID Download
3) Cable : Serial(9Pin or USB) to D-sub 15Pin cable, D-sub

15Pin cable, DVI to HDMI cable.

1) As above Fig. 1, Connect the Set, EDID Download Jig,,

PC & Cable

2) Turn on the PC & EDID Download Jig. And  Execute the

S/W : EDID TESTER Ver.2.5

3) Set up the S/W option 

Repeat Number : 5
Device Address : A0
PageByte : 8

4) Power on the Set

- DDC data of Analog-RGB

(1) Init the data

(2) Load the EDID data.( Open File ).

[ Anaolg – RGB   : LP61A/C _RGB.ANA ]
[ Digital – HDMI  : LP61A/C _HDMI.DVI ]

(3) Set the S/W as below.

4) Push the “Write Data & Verify” button. And confirm “Yes”.

- 9 -

<Fig. 1> Connection Diagram of DDC download

<Fig. 2>

<Fig. 3>

<Fig. 4>

- 10 -

5) If the writing is finished, you will see the “ OK” message. 

<EDID DATA Analog Set : 128bytes>

< EDID DATA Digital Set : 256bytes>

=> Detail EDID Options are below(a, b, c, d, e)

a. Product ID

b. Serial No :  Controlled on production line

c. Month, Year : Controlled on production line  

ex) Montly: '03'  =>  '03' 

Year:  '2005' =>  '0F'

d. Model Name(Hex): 

e. Checksum: Changeable by total EDID data

1) Remote controller for adjustment 
2) Color Analyzer (CA-110 or CA-210 or same product)
3) Auto W/B adjustment instrument(only for Auto adjustment)
4) AV Pattern Generator 

# Auto adjustment Map(RS-232C) 

Model

Product ID

Name

DEC

HEX

EDID table

26LC2RH

22045(A)

561D

1D56

30229

25621

1E56

32LC2RH

30057(A)

7569

6975

30058(D)

756A

6A75

Model Name

Model Name(HEX)

26LC2RH-ZJ

32    36    4C    43    32    52    2D    5A    4A

32LC2RH-ZJ

33    32    4C    43    32    52    2D    5A    4A

Communication

Type

LP61D

Protocol

Baud Rate

Data bit

Stop bit

Parity

115200

8

1

None

Protocol

Index

Cmd 1 Cmd 2 Data Min Value Max Value

Setting

R Gain

j

a

00(00)

255(FF)

G Gain

j

b

00(00)

255(FF)

B Gain

j

c

00(00)

255(FF)

R Offset

j

d

00(00)

255(FF)

G Offset

j

e

00(00)

255(FF)

B Offset

j

f

00(00)

255(FF)

<Fig. 5> EDID DATA

<Fig. 6> Connection diagram of auto W/B adjustment

- Operate the zero-calibration of the CA-110, then stick sensor

to LCD module when you adjust. 

- For manual adjustment, it is also possible by the following

sequence

1) Select RF no signal by pressing POWER ON key on remote

control for adjustment then operate heat run more than 15
minutes. 

2) As below Fig. 7, Supply 216Level (85 IRE) full screen

pattern to Video input.

3) Press the TV/AV KEY on R/C for converting input mode.
4) Set the PSM to Standard mode in Picture menu.
5) Enter the White Balance adjustment mode by pressing the

INSTART key twice(White Balance) on R/C.

6) Stick sensor to center of the screen and select each items

(Red/Green/Blue Gain and Offset) using 

F /G (CH +/-) key

on R/C.

7) Adjust Only High Light with R Gain / B Gain using  D/E

(VOL +/-) key on R/C.

8) Adjust it until color coordination becomes as below. 

(Initially, R/G/B gain and R/G/B offset values are fixed as below 
Red Gain :  2A8 ,    Green Gain :  2A8 ,     Blue Gain : 2A8
Red Offset :  00,     Green Offset :  00 ,     Blue Offset : 00 )

Brightness  :

High Light :      80 ± 20 Cd/m2

Color-Coordinate : 

High Light :  

X ; 0.285 ± 0.003
Y ; 0.290 ± 0.003

Color Temperature : 9,300±K ±500K 

7) Adjust it until color coordination becomes as below. 

(Initially, R/G/B gain and R/G/B offset values are fixed as

below)

Red Gain :   80 ,    Green Gain :    80 ,     Blue Gain :   80
Red Offset : 80,     Green Offset :  80 ,     Blue Offset : 80

8) When adjustment is completed, Exit adjustment mode

using EXIT key on R/C

1) Push the ADJ key in a Adjust Remocon.
2) Input the Option Number that was specified in the BOM,

into the Shipping area.

3) The work is finished, Push 

A

Key.

- 11 -

<Fig 7> Pattern for Adjustment of White Balance

- 12 -

To turn the TV on or off

To turn the TV on automatically if the power is supplied to the TV.(Use the

POWER key to deactivate): It should be deactivated when delivered.

To activate the mute function.

To check TV screen image easily.

To check TV screen sound easily

To select size of the main screen (Normal, Spectacle, Wide or Zoom)

Switch to closed caption broadcasting

To toggle on/off the teletext mode

To select an external input for the TV screen

To start turbo sound

To start turbo picture

To enter adjustment mode when manufacturing the TV sets.

To adjust the screen voltage (automatic): In-start 

mute 

Adjust 

AV(Enter into W/B adjustment mode)

W/B adjustment (automatic): After adjusting the screen 

W/B

adjustment

Exit two times (Adjustment completed)

To enter into the adjustment mode. To adjust horizontal line and sub-brightness.

To select the multiple sound mode (Mono, Stereo or Foreign language)

To release the adjustment mode

To easily adjust the screen according to surrounding brightness

To easily adjust sound according to the program type

To check component input

To check the front AV

To move channel up/down or to select a function displayed on the screen.

To adjust the volume or accurately control a specific function.

To set a specific function or complete setting.

To move the channel down in the PIP screen.

To use as a red key in the teletext mode

To move the channel in the PIP screen

To use as a green key in the teletext mode

To switch between the main and sub screens

To use as a yellow key in the teletext mode

To select the input status in the PIP screen

To use as a blue key in the teletext mode

To set a function that will automatically adjust screen status to match

the surrounding brightness so natural color can be displayed.

To select the functions such as video, voice, function or channel.

To set the delivery condition status after manufacturing the TV set.

To halt the main screen in the normal mode, or the sub screen at the PIP screen.

Used as a hold key in the teletext mode (Page updating is stopped.)

Displays the teletext time in the normal mode

Enables to select the sub code in the teletext mode

Used as the size key in the PIP screen in the normal mode

Used as the size key in the teletext mode

Used as the index key in the teletext mode (Top index will be

displayed if it is the top text.)

To select the position of the PIP screen in the normal mode

Used as the update key in the teletext mode (Text will be

displayed if the current page is updated.)

Used as Mode in the teletext mode

To select the simultaneous screen

To adjust screen tilt

To manually select the channel.

1

POWER

2

POWER ON

3

MUTE

4

P-CHECK

5

S-CHECK

6

ARC

7

CAPTION

8

TXT

9

TV/AV

10

TURBO SOUND

11

TURBO PICTURE

12

IN-START

13

ADJ

14

MPX

15

EXIT

16

APC(PSM)

17

ASC(SSM)

18

MULTIMIDIA

19

FRONT-AV

20

CH ±

21

VOL ±

22

ENTER

23

PIP CH-(OP1)

24

PIP CH+(OP2)

25

PIP SWAP(OP3)

26

PIP INPUT(OP4)

27

EYE

28

MENU

29

IN-STOP

30

STILL

31

TIME

32

SIZE

33

MULTI PIP

34

POSITION

35

MODE

36

PIP

37

TILT

38

0~9

NO

KEY

FUNCTION

REAMARK

Shortcut keys

Shortcut keys

Shortcut keys

Use the AV
key to enter
the screen
W/B
adjustment
mode.

Shortcut keys

Shortcut keys

Shortcut keys