DOWNLOAD LG 26LC45 / 26LC46 / 26LC4D (CHASSIS:LD73A) Service Manual ↓ Size: 5.47 MB | Pages: 44 in PDF or view online for FREE

- 13 -

- Remote controller for adjustment
- MSPG-925F Pattern Generator

(Which has XGA [1024*768] 60Hz 8 Color Bar pattern
shown in Fig. 1)

1) Input the PC 1024x768@60Hz 100% Color Bar pattern

(MSPG-925F model:37, pattern:33) into RGB. 
(Using D-sub to D-sub cable)

2) Set the PSM to Dynamic mode in Picture menu.
3) Press the IN-START key on R/C for adjustment
4) Press the 

G

(Vol.+) key operate To set , then it becomes

automatically.

5)  Auto-RGB OK means adjustment is completed.

* Test Equipment

Color Analyzer (CA-210/CH.9)
-> When you adjust LCD color temperature, on Color
analyzer (CA-210), you should use Channel 9 which is
Matrix compensated (White, Red, Green, Blue revised) by
CS-1000 and adjust in accordance with White balance
adjustment coordinate which is specified on the next.

* Color temperature standards according to CSM and Module

Cool : 11,000k
Medium : 9,300k
Warm : 6,500k

* White balance adjustment coordinate and color temperature

- PC (for communication through RS-232C)

-> UART Baud rate : 115200 bps

- Luminance Y AV : upper 150 cd/ß≥ (Typ : 350 cd/ß≥)

-> Applying to Cool, Medium, Warm mode

* Connecting picture of  the measuring instrument (On

Automatic control )
Inside PATTERN is used when W/B is controlled. Connect to
auto controller or push control R/C IN-START  
-> Enter the mode of White-Balance, the pattern will come
out.

* Auto-control interface and directions

1) Adjust in the place where the influx of light like floodlight

around is blocked. (illumination is less than 10ux).

2) Adhere closely  the Color Analyzer ( CA-210 ) to the

module less than 10cm distance, keep it with the surface
of the Module and Color Analyzer’s Prove
vertically.(80~100°).

3) Aging time  

- After aging start, keep the power on (no suspension of

power supply) and heat-run over 15 minutes.

- Using ‘no signal’ or ‘full white pattern’ or the others,

check the back light on.

- One of R Gain / G Gain / B Gain should be kept on 80, and

others  are controlled lowering from 80 

1) Press ‘power on’ of the control R/C, set heat run to white by

pressing 

G

, and heat run over 15 minutes. (Set : RS-233

Host : PC, Baud Rate : 115200bps, Download : Cortez)

2) Zero Calibrate CA-210, and when controlling, stick the

sensor to the center of LCD module surface.

3) Double click In-start key on Controlling R/C and get in ‘white

balance’.

4) Set test-pattern on and display inside pattern. Control is

carried out on three color temperature, COOL, MEDIUM,
WARM. (Control is carried out three times,)

5) When the R/G/B GAIN is 80 on OSD, it is the FULL

DYNAMIC Range of the Module. In order to control white
balance without the saturation of FULL DYNAMIC Range
and DATA, one of R Gain / G Gain / B Gain should be kept
on 80, and other two is controlled lowering from 80.

* Color Temperature: Cool, Medium, Warm

1) When R GAIN is set to 80

- Control G GAIN and B GAIN by lowering from 80. 

2) When B GAIN is set to 80

- Control R GAIN and G GAIN by lowering from 80.

3) When G GAIN is set to 80

- Control R GAIN and B GAIN by lowering from 80.

One of R Gain / G Gain / B Gain should be kept on 80,
and adjust other two lower than 80.
(When R/G/B GAIN are all 80, it is the FULL DYNAMIC
Range of Module)

x

0.276

0.276±0.002

y

0.283

0.283±0.002

Δuv

0.000

0.000

x

0.285

0.285±0.002

y

0.293

0.293±0.002

Δuv

0.000

0.000

x

0.313

0.313±0.002

y

0.329

0.329±0.002

Δuv

0.004

0.004

<Fig. 2> Connecting picture (On Automatic Control)

(1) Setting up like bottom figure (After setting white balance,

this is set)
1) Press ADJ Key in the Adjust remocon.
2) Select  “System Control 2” by using 

D

/

E

(CH+/-) key,

and press 

A

(ENTER).

3) Using Adjust remocon, RS-232 Host & Baud Rate &

Download value change (RS-232 Host:Gprobe, Baud
Rate:115200bps, Download:Cortez)

(2) Bar-code scanning

1) Push the menu button in DTV mode. 

Select the STATION -> Diagnostics -> To set

2) Check the Serial Number.

- 14 -

- 15 -

Start check

Manufacture’s model

passage

1. Check the Power Off

status.

Does the whole
screen appear?

Is it 

identical to when the

power is off?

No

Yes

No

Yes

Yes

Yes

Yes

2. Check the Interface

signal status.

Is the Interface 

signal operating?

Yes

3. Check the St-by 5V

signal circuit.

Does the 

low pressure output

appear?

Does the 

St-by 5V signal 

appear?

No

No

Yes

4. Check the 5V Monitor

signal circuit.

Does the 

5V Monitor signal 

appear?

No

7. Check the VSC Vs-ON

signal 

Does the 

high tension output

appear?

Does the 

VSC signal Vs-ON

appear?

No

No

Does the

high tension 

output voltage

occur?

When

removing  the Y B/D

Module input connector,

does output voltage

drop?

When the

Y, Z B/D Module

input connector, does Power

Board high tension 

output voltage drop?

No

No

No

9. Check the Power

Board Output high

tension circuit

Yes

10. Check the Z B/D

Module output circuit

Yes

When 

removing the Z B/D

Module input connector,

does output voltage

drop?

11. Check the Y B/D

Module output circuit

Yes

Yes

8. Check the Vs, Va

voltage output circuit.

Does the 

Vs, Va voltage output

appear?

No

Yes

Yes

5. Check the VSC RL-ON

signal.

Does the 

VSC signal RL-ON

appear?

No

6. Check the VSC low

pressure output

Does the 

VSC low pressure

output appear?

No

- 16 -

1) Does not  minute discharge at module. 
2) Non does not come into the front LED. 

Is the power cord plugged in?

Plug in the power cord.

Yes

No

Is the Line Filter and Power

Board Cable connected?

Connect the Cable.

Yes

No

Is the appropriate Fuse(F101) on

the Power Board?

Replace the Fuse.

Yes

No

Is the Power Board and 13P of

VSC Board Cable connected?

Connect the Cable.

Yes

No

After removing the cables, connect them to the Power Board(except the
SC101 connection cable), and change the AC voltage marking to manual.
When ST-BY 5V does not operate, replace the Power Board.