DOWNLOAD LG 26LC2R (CHASSIS:LN61A) Service Manual ↓ Size: 7.7 MB | Pages: 28 in PDF or view online for FREE

- 13 -

3) Execute ‘Download_CS.vi2c’ program in PC, then a

main widow will be opened.

4) Click "GO" button

If you don’t push the "go", the Hex file would not be
downloaded although the download proceeds
normally at first glance

5) Double click the blue box and confirm "Boot loader

Version" as 40.

6) Click the "Erase Flash" button

7) Double click the download file low then, "edit" window
will be opened

8) Chick the choice button I n the "edit window", then

"file choice window’ will be opened

9) Choose the Hex file in folder and execute

downloading with click "open button"

10) Click OK button at the "edit window"

11) Under Downloading progress

12) If download is failed, for example "No acknowledge

from slave", execute download again from (1)

Double click

- 14 -

4.1.3. Channel memory download

(1) Connect the download jig to D-sub jack
(2) Execute ‘Channel.vi2c’ program in PC, then a main

window will be opened.

(3) Push the button change and select the Channel

memory data

(4) Check the communication is OK or not.

=> Push the Read area (Ackn. Check) and check Cyan

area is OK message.

(5) Push the Update NVM from File

4.1.4. Tool Option Area Option Change

Before PCBA check, have to change the Tool option and
Area option.
Option values are in BOM. (If on changed the option, the
input menu can differ the model spec.)
The input methods are same as other chassises(Use adj
Key on the Adjust Remote control)

4.1.5. Color carrier Adjustment(Inspection process)

(1) Tuning the RF signal

NTSC Digital Pattern(with color Bar)

(2). push the "adj" key in the adjustment remote control.

* Caution : Each PCB assembly must be checked by check

JIG set.(Because power PCB Assembly damages
to LCD Module, especially be careful)

4.2.1 EDID(The Extended Display Identification Data)/ DDC

(Display Data Channel) download

* Caution

- Use the proper signal cable for EDID Download
- Never connect HDMI & D-SUB Cable at the same time.
- Use the proper cables below for EDID Writing

* EDID Data

<EDID DATA Analog Set : 128bytes>

[LC2R SERIES & LC2RA/LC2RB SERIES ONLY different 70
Line because of Model name]

For HDMI EDID

For RGB EDID

Item

Manufacturer ID

Version

Revision

Condition

GSM

Digital : 1

Digital :3

Data

1E6D

01

03

- 15 -

< EDID DATA HDMI Set : 256bytes>

[LC2R SERIES & LC2RA/LC2RB SERIES ONLY different 70
Line because of Model name]

=> Detail EDID Options are below(a, b, c, d, e)

a. Product ID

b. Serial No :  Controlled on production line
c. Month, Year : Controlled on production line

ex) Monthly: '03'  =>  '03' 

Year:  '2005' =>  '0F'

d. Model Name(Hex): 

e. Checksum: Changeable by total EDID data

4.3.1. Required Equipment

- Remote controller for adjustment 
- Color Analyzer (CA-110 or CA-210 or same product; ch : 9)
- Auto W/B adjustment instrument(only for Auto adjustment)
- AV Pattern Generator 

Model : 207(NTSC-J), pattern:78(216 Gray)

4.3.2. Connecting diagram of equipment for measuring (For

Automatic Adjustment) 

[Push the "POWER ON" key at the Adjust Remote control
before Adjustment of W/B, the Baud rate & PSM, CSM will
change 115200bps, Standard (MJ: Optimum), Normal]

# Auto adjustment Map(RS-232C)

4.3.3. Adjustment of white balance (for manual adjustment)

- Operate the zero-calibration of the CA-110, then stick

sensor to LCD module when you adjust. 

- For manual adjustment, it is also possible by the following

sequence

1) Select RF no signal by pressing 

POWER ON key on

remote control for adjustment then operate heat run
more than 15 minutes. 

(If not executed this step, the condition for W/B will be
differ. The W/B condition is PSM : Optimum, CSM :
Normal.)

2) As below picture, Supply 216Level (85 IRE) full screen

pattern to Video input.

26,32LC2R-UJ : VIDEO1 or VIDEO2 (Input 60Hz)

3) Press the POWER ON KEY on R/C for converting input

mode.

4) Enter the White Balance adjustment mode by pressing

the IN-START key (White Balance) on R/C.

5) Stick sensor to center of the screen and select each

items(Red/ Green/ Blue Gain and Offset) using 

D

/

E

(CH+/-) key on R/C.

6) Adjust Only High Light with R Gain / B Gain using 

F

/

G

(VOL +/-) key on R/C.

7) Adjust it until color coordination becomes as below.

(Initially, R/G/B gain and R/G/B offset values are fixed
as below)
Red Gain : 80 ,    Green Gain : 80 ,   Blue Gain : 80
Red Offset : 80,   Green Offset : 80,  Blue Offset : 80

Model Name

Model Name(HEX)

26LC2R-UJ

32

36

4C

43

32

52

2D

55

4A

Model Name

Product ID

Analog or

DEC

HEX

EDID table

Digital

26LC2R

A

22045

561D

1D56

D

22046

561E

1E56

Communication

Type

LP61A/C, LN61A

Protocol

Baud Rate

Data bit

Stop bit

Parity

115200

8

1

None

Protocol

Index

Cmd1 Cmd2

Data

Def. Value

Setting

Min Value Max Value

R Gain

j

a

00(00)

202(CA)

128(80)

G Gain

j

b

00(00)

202(CA)

128(80)

B Gain

j

c

00(00)

202(CA)

128(80)

R Offset

j

d

00(00)

255(FF)

128(80)

G Offset

j

e

00(00)

255(FF)

128(80)

B Offset

j

f

00(00)

255(FF)

128(80)

- 16 -

* Target Value [PSM: Optimum, CSM: Normal]

- Normal (9300K)    x ; 0.283±0.003  y ; 0.298±0.003
- Luminance(Y)    AV : upper 150 cd/m

2

(Typ. : 350 cd/m

2

)

[AT W/B condition - PSM:Optimum, CSM:Normal, Pattern:
78 (216Gray)]

=> Reference Value(Automatically fixed)

- Cool(11000K): x:0.274±0.003, y: 0.286±0.003
- Warm(7200K) : x:0.303±0.003, y: 0.319±0.003

<Pattern for Adjustment of White Balance>

8) When adjustment is completed, Exit adjustment mode

using EXIT key on R/C

4.4.4. Input the Shipping Option Data 

1) Push the ADJ key in a Adjust Remote control.
2) Input the Option Number that was specified in the BOM,

into the Shipping area.

3) The work is finished, Push 

A

Key.

(Default values maybe modified the module condition)

- White Balance

W h i t e

a l a n c e

B

<Default Value on OSD>