DOWNLOAD LG 22LV2130 (CHASSIS:LP91U) Service Manual ↓ Size: 3.03 MB | Pages: 31 in PDF or view online for FREE

5.2.2. Adjustment of White Balance (for Manual adjustment)

(1) Color analyzer(CA100+, CA210) should be used in the

calibrated ch by CS-1000.

(2) Operate the zero-calibration of the CA100+ or CA-210,

then stick sensor to the module when adjusting.

(3) For manual adjustment, it is also possible by the following

sequence.

1) Select white pattern of heat-run by pressing “POWER

ON” key on remote control for adjustment then operate
heat run longer than 15 minutes. (If not executed this
step, the condition for W/B may be different.)

2) Push “Exit” key.
3) Change to the AV mode by remote control.
4) Input external pattern (85 % white pattern)
5) Push the ADJ key -> Enter “0000” (Password)
6) Select “3. W/B ADJUST”.
7) Enter the W/B ADJUST Mode.
8) Stick the sensor to the center of the screen and select

each items (Red/Green/Blue Gain and Offset) using

D

/

E

(CH +/-) key on Remote control.

9) Adjust R/G/B Gain using 

F

/

G

(VOL +/-) key on Remote

control.

10) Adjust three modes all (Cool/ Medium/ Warm) : Fix the

one of R/G/B gain and change the others

11) When adjustment is completed, Enter “COPY ALL”.
12) Exit adjustment mode using EXIT key on Remote control.

* CASE

First adjust the coordinate far away from the target value(x, y).
1. x, y > target

i) Decrease the R, G. 

2. x, y < target

i) First decrease the B gain, 
ii) Decrease the one of the others.

3. x > target, y < target

i) First decrease B, so make y a little more than the target.
ii) Adjust x value by decreasing the R.

4. x < target, y > target

i) First decrease B, so make x a little more than the target.
ii) Adjust x value by decreasing the G.

(4) Standard color coordinate and temperature when using the

CA100+ or CA210 equipment

1) All Edge LED(except LGD), lamp over 26 inch

under 22 inch.

3) W/B table in process of time which must be applied for

LGD edge LED module(Target color coordinate is
different by aging time)

- To check the Coordinates of White Balance, you have to

measure at the below conditions.

Picture Mode : Select Vivid and change Dynamic Contrast :
Off, Dynamic Colour : Off -> Picture Mode change ->
Vivid(User)
(If you miss the upper condition, the coordinates of W/B can
be lower than the spec.

- 13 -

Coordinate

Mode

x

y

Temp

uv∆

Cool

0.269 ± 0.002  0.273 ± 0.002

13,000 K

0.000

Medium

0.285 ± 0.002

0.293 ± 0.002

9,300 K

0.000

Warm

0.313 ± 0.002

0.329 ± 0.002

6,500 K

0.003

Coordinate 

Mode

x

y

Temp

uv∆

Cool

0.285 ± 0.002

0.293 ± 0.002

9,300 K

0.000

Medium

0.295 ± 0.002

0.305 ± 0.002

8,000 K

0.000

Warm 0.313 

± 0.002

0.329 

± 0.002

6,500 

K

0.003

Aging Time

Cool

Medium

Warm

GP2R

(Min.)

X

Y

X

Y

X

Y

269

273

285

293

313

329

1

0-2

279

288

295

308

319

338

2

3-5

278

286

294

306

318

336

3

6-9

277

285

293

305

317

335

4

10-19

276

283

292

303

316

333

5

20-35

274

280

290

300

314

330

6

36-49

272

277

288

297

312

327

7

50-79

271

275

287

295

311

325

8

80-149

270

274

286

294

310

324

9

Over 150

269

273

285

293

309

323

- 14 -

No power

(LED indicator off)

Check 24V, 12V, 3.5V 

of Power B/D

Check short of Main B/D 

or Change Power B/D

Pass

Check Output of

IC1001, IC1002, IC1003,

 IC1005, IC1007 

Check P403 Connector 

Change LED Assembly 

:  

[A] PROCESS(for non-adapter models)

Fail

Fail

Pass

Pass

Check LED Assembly 

Change IC1002, IC1008, Q1003

Pass

Check short of

IC1001, IC1002, IC1003,

 IC1005, IC1007

Fail

Re-soldering or Change defect part

Fail

No Raster

[B]: Process

Check LED status

On Display Unit

Repeat [A]/[A-1] Process

Pass

Fail

Check PANEL_VCC

of LVDS wafer

Check Output of Q1003

Fail

Change Inverter Connector

Or Inverter

Fail

Pass

Fail

Pass

Change LVDS cable

Fail

Check LVDS Cable

Pass

Check Panel Link Cable 

Or Module

Change Panel Link Cable

Or Module

Check Inverter Connector

Or Inverter

Pass

- 15 -

No Raster on PC Signal

Check Input source Cable

And Jack

Pass

Re-soldering or 
Change the defect part

Pass

Check the Input/Output

Of IC201

Fail

Re-soldering or 

Change the defect part,

Check RGB EDID Data

Repeat [A]/[A-1], & [B] Process

Pass

Check the Input/Output

Of J202

Fail

Pass

Check the Input/Output

Of IC800

Fail

Re-soldering or 

Change the defect part

Pass

No Raster on COMMPONENT Signal

Check Input source 

Cable And Jack

Pass

Re-soldering or 

Change the defect part

Check the Input/Output

Of IC800

Fail

Pass

Re-soldering or 

Change the defect part

Repeat [A]/[A-1], & [B] Process

Check The Input/Output

Of JK101

Fail

Pass

No Raster on HDMI Signal

Check Input source 

Cable And Jack

Pass

Check the Input/Output
of JK301, JK302, JK303

Fail

Re-soldering or 

Change the defect part

Pass

Pass

Check the Input/Output
of IC300, IC301, IC303

Fail

Re-soldering or 

Change the defect part
Check HDMI EDID Data

Re-download HDCP

Pass

Pass

Check the Input/Output

of IC800

Fail

Re-soldering or 

Change the defect part

Repeat [A]/[A-1], & [B] Process

- 16 -

No Sound

Check The Input Sourse 

Check The Input/

Output of IC501

Re-soldering or 

Change the defect part

Fail

Pass

Pass

Check The Speaker

Change Speaker 

Fail

Check The Speaker Wire

Pass

Change The Source Input

Fail

No Raster On AV Video Signal

No Signal On TV(RF) Signal

Check Input source 

Cable And Jack

Pass

Check Input source 

Cable and Jack

Pass

Check The Input/

Output of JK103

Re-soldering or 

Change the defect part

Pass

Fail

Pass

Repeat [A]/[A-1], & [B] Process

Pass

Check the Input/

Output of IC800

Fail

Re-soldering or 

Change the defect part

Pass

Check The Input/

Output of TU600

Of TU500

Re-soldering or 

Change the defect part

Pass

Fail

Pass

Check the Input/

Output of IC800

Fail

Re-soldering or 

Change the defect part

Repeat [A]/[A-1], & [B] Process