DOWNLOAD LG GR-B-L207EC-ER Service Manual ↓ Size: 5.21 MB | Pages: 127 in PDF or view online for FREE

■

1. The icemaker requires the water pressure of 1.5 -

8.5kgf/cm

2

. (It is acceptable if city water fills a cup of 

180cc with water for 3 seconds)

2. Install booster pump where the city water pressure is 

below 1.5kgf/cm

2

for normal operation of water and ice 

dispenser.

3. The total length of water pipe shall be less than 12m. Do

not bend the pipe at right angle. If the length is more
than 12m, there will be troubles on water supply due to 
water pressure drop.

4. Please install water pipe where there is no heat around.

■

- 19 -

Valve Feed

5221JA3001A

Common Use

Connector, (MECH) Pipe

4932JA3003A

Conversion Connector(3/4")

6631JA3004A

No Holes

Balance Conector(3/4")

6631JA3004B

Packing(ø24x3t)

3920JA3001B

Connector, (MECH) Pipe

4932JA3003B
Conversion Connector(W25)

6631JA3004C

No Holes

Balance Conectoor(W25)

6631JA3004D

Packing(ø23x3t)

3920JA3001A

Connector, (MECH) Pipe

4932JA3003C

Conversion Connector(W28)

6631JA3004E

No Holes

Balance Conector(W28)

6631JA3004F

Packing(ø26x3t)

3920JA3001C

Connector, (MECH) Pipe

4932JA3003D

Conversion Connector(1/2")

6631JA3004G

No Holes

Balance Conector(1/2")

6631JA3004H

Packing(ø19x3t)

3920JA3001D

Conve-
rtible
Water
Valve

Water
Conn-
ector

Valve Feed

Rubber, Packing

Connector, Pipe

Tape, Teflon

Connector, Pipe

1) Turn off main valve of water pipe.

2) Disconnect water tap from piping by loosening nuts.

3) Connect pipe connector A and B to piping after sealing

the pipe connector with sealing tapes.

4) Connect feed valve to pipe connector A.

5) If there is only one tap water pipe, connect pipe 

connector A only and  install feed pipe.

1) After the installation of feed water, plug the refrigerator 

to the earthered wall outlet, press the water dispenser
button for 2 - 3 minutes, and confirm that the water
comes out.

Caution : • Feed pipe should be connected to cold water 

line. If it is connected to hot water line, trouble 
may occur.

• Please check rubber packing when connecting 

feed pipe.

2) Check leakage at connecting part, then arrange water

tube and locate the refrigerator at its regular place if
there is no leaking.

- 20 -

Feed

Valve

Feed

Valve

Feed

Valve

Feed

Valve

Pipe Connector B

Hot Water

Pipe Connector A

Feed

Valve

Cold Water

How to wind

Sealing Tapes.

Water Tube

Water Tube

Nut

*If customer wants to use bottled water, extra pump should be installed as shown below.

1. The pump system should not be on the floor (it may cause noise and vibration). Securely fasten the inlet and outlet

nuts of pump.

2. If there is any leakage after installation, cut the water tube at right angle and reassemble.
3. When put the water tube end into the bottle, leave a clearance between bottle bottom and water tube end.
4 Check water coming out and any leakage.

Caution : • If feed tube is more than 4m, less water will come out due to pressure drops.

• Use standard feed tube to prevent leaking.

■

1) Connect feed tube to the filter outlet and water valve connecting tube.

2) Fix the filter at proper place around the sink where it is easy to replace the filter and to receive the cleaning water. 

Please consider the length of tube shall be less than 12m when locating filter.

3) When fixing the filter, use fixing plate and cable depending on the surrounding conditions.

1) Connect feed tube to the inlet of feed valve and filter.

2) Clean the main valve and feed valve with water for at

least one minute until clean water comes out.

- 21 -

Water Tube

Nut

Inlet

Outlet

Fixing Plate

Fixing Plate

Fixing Cable

Water

Filter

Filter Inlet

Feed Valve

Hot Water

Cold Water

■

■

1. Before installing the filter, take out the top shelf of the

refrigerator after tilting it to the direction (

a

) and lifting it

to the direction (

b

) and move it to the lower part.

2. Remove the lamp cover by  pressing the protrusion

under the cover and pulling the cover to the front.

■

1. Initial installation of water filter

Remove the filter substitute cap by turning it
counterclockwise (

a

) by 90 degrees and pulling it down.

Note : Keep it safe to use it later when you do not use the

filter.

Remove the red cap from the filter and attach the sticker.
Insert the upper part of the filter (

a

) after aligning with

the guideline marked on the control box, and fasten it by
turning it clockwise by 90 degrees.

Note : Check that the guideline and the fastening

indication line are aligned.

2. Replacement of water filter

While holding the lower part of the filter, turn it
counterclockwise (

a

) by 90 degrees and pull it down.

Note : Check that the guideline and the loosening

indication line are aligned.

■

Reassemble the lamp cover and the top shelf of the
refrigerator. To place the top shelf of the refrigerator, raise
the front part of the shelf a bit so that the hook of the shelf
is fit into the groove.
In order to clean the water filter system, drain water for
about 3 min.

Note : Then open the door of the refrigerator and check for

water droppings on the shelf under the filter.

- 22 -

Control box

Aligning with the guide line
and the fastening indication line

Control box

Aligning with the guide line
and the loosening indication line

Separation
of red cap

Adhesion
sticker

Substitute
cap