LG GR-372SF Service Manual ▷ View online
NOTE : This is a basic model. The shape of refrigerator is subject to change.
2. PARTS IDENTIFICATION
- 5 -
Egg Storage Rack
Freezer Door Rack
Refrigerator Door
Rack
Rack
Leveling Screw
FREEZER
COMPARTMENT
Freezer Temperature
Control Dial
Ice Trays
Twisting Ice Serve(Option)
or
General Type Ice Making
Freezer Shelf
(Plastic or Steel)
REFRIGERATOR
COMPARTMENT
Deodorizer
(Option)
Chilled Room
Temperature
Control Dial
Lamp
F.I.R Lamp (Option)
Shelves
(Plastic or Steel)
Multi Flow Duct
Distributes cold air to
each part of refrigerator
compartment.
Vegetable Drawer
Used to keep fruits
and vegetables, etc.
fresh and crisp.
Dairy Corner
(Option)
(Option)
Bottle Guide
Movable Rack
Wine Rack(Option)
3-1 DOOR
●
Freezer Door
1. Remove the hinge cover by pulling it upwards.
2. Loosen hexagonal bolts fixing the upper hinge to the
2. Loosen hexagonal bolts fixing the upper hinge to the
body and lift the freezer door.
3. Pull out the door gasket to remove from the door foam
Ass'y.
●
Refrigerator Door
1. Loosen hexagonal bolts fixing the lower hinge to the
body to remove the refrigerator door only.
2. Pull out the door gasket to remove from the door foam
Ass'y.
3-2 DOOR SWITCH
1. To remove the door switch, pull out it with a '—' type
driver as shown in (figure 9).
2. Disconnect the lead wire from the switch.
3-3 THERMOSTAT
1. Remove the Cover Lamp-R by the use of '–––' type driver
inserting in the low holes of the cover.
2. Loose 2 screw.
3. Pull the Control Box-R.
4. Disconnect the Housing of lead wire.
5. Separate the INSU'Multi Duct and Control Box-R.
6. Dissasemble the Knob.
7. Separate the Thermostat and Control Box-R.
8. Separate the Thermostat and Resistor.
9. Disconnect the lead wire.
3. Pull the Control Box-R.
4. Disconnect the Housing of lead wire.
5. Separate the INSU'Multi Duct and Control Box-R.
6. Dissasemble the Knob.
7. Separate the Thermostat and Control Box-R.
8. Separate the Thermostat and Resistor.
9. Disconnect the lead wire.
3.4 FAN AND FAN MOTOR
1. Remove the freezer shelf.
2. Separate the twist by pulling right.
3. Loosen 1 cap screw fixing the Grille Fan.
4. Loose 1 screw.
5. Pull out the Grille Fan and Shroud-F.
2. Separate the twist by pulling right.
3. Loosen 1 cap screw fixing the Grille Fan.
4. Loose 1 screw.
5. Pull out the Grille Fan and Shroud-F.
3. DISASSEMBLY
- 6 -
BOLT
HINGE
HINGE COVER
GASKET
LOWER HINGE
BOLT
Figure 6
Figure 7
Figure 8
Figure 9
INSU' MULTI DUCT
THERMOSTAT
CONT' BOX-R
COVER LAMP-R
RESISTOR
Figure 10
CAP
Figure 11
6. Disconnect the housing of lead wire.
7. Separate the Fan Assy.
8. Loose 2 screw fixed to the Bracket.
9. Pull out Shroud-F remove the Fan Motor Assy.
10. Separate the Motor Bracket and Rubber.
7. Separate the Fan Assy.
8. Loose 2 screw fixed to the Bracket.
9. Pull out Shroud-F remove the Fan Motor Assy.
10. Separate the Motor Bracket and Rubber.
3-5 DEF' CONTROL ASSY
Def control Assy consists of Defrost Thermostat and FUSE–M.
Defrost Thermostat functions to defrost automatically and it
is attached to metal side of the Evaporator and senses
Temp.
Fuse-M is a kind of safety device for preventing over-
heating of the Heater when defrosting.
At the temperature of 77°C, it stops the emission of heat
from the Heater.
1. Pull out the Shroud after removing the Grille.
2. Separate the connector connected with the Def Control
Defrost Thermostat functions to defrost automatically and it
is attached to metal side of the Evaporator and senses
Temp.
Fuse-M is a kind of safety device for preventing over-
heating of the Heater when defrosting.
At the temperature of 77°C, it stops the emission of heat
from the Heater.
1. Pull out the Shroud after removing the Grille.
2. Separate the connector connected with the Def Control
Assy and replace the Def Control Assy after cutting the
Tie Wrap and removing the Holder Fuse. (Figure 14)
Tie Wrap and removing the Holder Fuse. (Figure 14)
3-6 REFRIGERATOR ROOM LAMP
1. Remove the cover lamp-R by pulling with a '–––' type
driver.
2. Remove the lamp-R by turning.
3-7 CONTROL BOX-R
1. Remove the Cover Lamp-R.
2. Loosen 2 screws.
3. Full the Control Box-R.
4. Separate the lead wire Housing.
- 7 -
FAN
SHROUD
FAN MOTOR
BRACKET
GRILLE
Figure 12
SHROUD-F
Figure 13
FAN
DEF-THERMO
FUSE-M
HOLDER FUSE
Figure 14
REFRIGERATOR ROOM LAMP
Figure 17
CONTROL BOX-R
COVER LAMP
Figure 18
3-8 REPLACEMENT OF DOOR OPENING TYPE
●
Precaution
1. Before replacing the door opening type, first of all, you should take out
foodstuffs and accessories like shelves or trays, and so on which are not fixed
in the refrigerator.
in the refrigerator.
2. Use the '+' Driver, Bolt Driver, Torque Wrench or Spanner to fix or remove the
bolt.
3. Be careful not to fall down the refrigerator in disassembling or assembling the
Hinge Lower and the Adjustable Screw Asm. Don't lay the refrigerator down in
working with it, it will cause to get out of order.
working with it, it will cause to get out of order.
4. Be careful not to drop the door in disassembling or assembling the freezer or
the refrigerator door.
5. This refrigerator, according to the install position or user's liking, can be used
as the type of opening from the right or the left.
W
HOW TO REPLACE THE DOOR OPENING TYPE
- 8 -
1
Separate the Cap
➊
and Hinge Upper
➋
.
2
Separating the Freezer Door
➌
.
3
Separating the Hinge-C
➍
and the Refrigerator
Door
➎
.
4
Separating the Hinge Lower
➏
.
2
1
4
5
6
3
- Converting Door is Optional
Click on the first or last page to see other GR-372SF service manuals if exist.