DOWNLOAD LG GR-267 Service Manual ↓ Size: 22.52 MB | Pages: 127 in PDF or view online for FREE

Model
GR-267
Pages
127
Size
22.52 MB
Type
PDF
Document
Service Manual
Brand
Device
Refrigerator
File
gr-267.zip
Date

LG GR-267 Service Manual ▷ View online

8. ICEMAKER ASSY 
8-1. Dispenser Model
1) How to disassemble:
(1) Remove ice bank from the freezer compartment.
(2) Loosen two screws on the upper part of icemaker
bracket.
(3) Disconnect icemaker bracket so that it can slide
forward.
(4) Disconnect icemaker housing and sensor housing.
(5) Disconnect icemaker horizontally by pressing bracket
hook part. ( Don’t disassemble further. The set value
may be changed.)
2) How to assemble : The assembly is the reverse order of
the above disassembly.  
Note :
When the ice tray is not horizontal after assembly,
assembly must be wrong. Check and assemble
again.
8-2. Basic Model
1) How to disassemble:
(1) Remove ice tray assy from the freezer compartment.
(2) Pull out knob from the ice tray in arrow direction.
(At this time, pull out a knob in arrow direction while
shaking right and left as the knob is connected to
pins in  A .)
(3) Spring can be removed by pulling ice tray in arrow
direction and pulling out a spring inserted in ice tray
axis from the hole of supporter ice tray.
2) How to assemble : Assembly is the reverse order of
disassembly.
Note :
It is important to put one end of spring into the hole
of the supporter ice tray and the other end on the
lower part of an ice tray when inserting spring into
the shaft.
HOW TO DISASSEMBLE AND ASSEMBLE
- 97 -
Bracket, Ice Maker
Hook
Ice Maker Unit
Lever
Tray, Ice
Sensor
Insulation
Cover, Sensor
Supporter Ice Tray
Pin
Knob
Ice Tray
Spring
9. DISPENSER
1) Disconnect button assembly by pulling down until it
stops and then pulling forward.
2) Remove display frame Assy by making a gap between a
display frame Assy. and funnel Assy. with a balde
screwdriver and pulling it forward. The cover dispenser
is fixed with a hook. 
3) Display Assy can be disconnected by pressing the
upper part of a cover dispenser and pushing a display
Assy. after disconnecting display frame Assy. housing.
4) Loosen four screws with a phillips screwdriver and pull a
funnel Assy to disconnect.
5) Duct cap Assy is disconnected if hold lever connecting
screw is loosened with a phillips screwdriver.
6) For assembling a duct cap Assy., insert one end of a
spring into the right hole of dispenser lever, and insert
the other end into the right hole in upper part of
dispenser. And then assemble a holder lever after fixing
a holder at a solenoid Assy working part. 
HOW TO DISASSEMBLE AND ASSEMBLE
- 98 -
Button
Funnel Assy
Funnel
Assy
Holder
Lever
Solenoid Assy
Cap 
Spring
Heater, Sheet
Lever,Dispenser
Solenoid Assy
7) Dispenser Related Parts
HOW TO DISASSEMBLE AND ASSEMBLE
- 99 -
15
17
14
2
4
5
3
1
6
22
24
23
21
13
12
7
16
18
21
19
9
10
8
11
1
FRAME ASSY, DISPLAY
2
COVER, DISPENSER
3
COVER, DISPLAY
4
PWB(PCB) ASSY, DISPLAY
5
BUTTON(DISPLAY)
6
DECO, DISPENSER
7
FUNNEL ASSY
8
SWITCH, MICRO
9
FRAME, FUNNEL
10 LEVER(SWITCH)
11 FUNNEL
12 RUBBER, FUNNEL
13 COVER, LAMP
14 SOLENOID ASSY
15 SPRING
16 HOLDER, LEVER
17 CAP, DUCT
19 LEVER, DISPENSER
20 RUBBER, CAP
21 BUTTON ASSY
22 BUTTON
23 HOLDER, BUTTON
24 DECO, DRAIN
< 17  Cap Assy, Duct Detailed Drawings>
10. WATER TANK AND WATER LINE
u
The water tank at back and lower part of a refrigerator is
fixed by one screw and has a capacity containing 7
glasses (180cc per glass) of cold water. It will take time
to make more cold water in the tank. 
* The first portion of dispensed water is not cold even
though the refrigerator is working. In this case,
dispense ice first in the cup and then water to make a
cold water. 
10-1. How to disassemble the water supply pipe 
a
1) Disconnect five fixtures mounted on the rear wall of the
refrigerator after disconnecting the water supply pipe 
a
from a water valve.
2) Remove a tie-wrap and two screws connected to the
rubber inject.
3) Replace the water supply pipe 
a
after disconnecting the
water supply pipe 
a
from a rubber inject. And assemble
the parts by performing disassembly in reverse order.
10-2. How to disassemble the water tank and the
water supply pipe   
1) Disconnect the water supply pipe 
b
from a water valve
on the back and lower part of the freezer. 
2) Disconnect the connector Assy. in water supply pipe at
lower part of the freezer door. 
3) Pull out the water supply pipe 
b
from the thermal
insulation materials after removing one screw and six
tie-wraps in the lower part of a refrigerator compartment. 
4) Replace a water tank or a water supply pipe 
b
and
assemble the parts by performing disassembly in
reverse order.
Note :
• The water supply pipe 
c
cannot be disassembled.
• Tightly fasten six tie-wraps to prevent leakage.
11. HOME BAR
11-1. Home Bar related parts 
11-2. Home Bar parts disassembly and assembly
1) Disconnect H/Bar Door Assy 
a
.
2) Loosen two screws 
h
attached on the refrigerator
compartment door with a phillips screwdriver. And
loosen 4 screws 
b
and two screws 
c
. Pull H/Bar door
Assy 
a
. forward to disassemble.
3) Loosen two screws 
k
j
fixed on H/Bar door Assy. and
two screws 
l
with a cross driver to disassemble arm
Assy.
4) Assemble parts by performing the disassembly in
reverse order.
Note : 
• Assemble carefully parts 
k
h
l
until they are
fixed firmly when assembling them. 
• Adjust exterior gap by adjusting parts 
b
h
and
when assembling.
HOW TO DISASSEMBLE AND ASSEMBLE
- 100 -
Rubber inject
Water Valve
Connect
Assy
2
3
Water supply pipe
Water supply pipe
Tie-Wrap
Connecting
Rubber
1
9
7
8
6
12
11
10
9
8
7
3
5
4
2
2.0
5.0
1.8
1.8
1   DOOR ASSY, H/BAR
7    CAP, ARM
2   SEREW, TAP TITE(HINGE-H/B)
8    SCREW TAP TITE(ARM)
3   BRACKET HINGE
9    ARM ASSY
4   SCREW MACHINE(HINGE-H/B)
10   STOPPER
5   HINGE ASSY H/BAR
11   SCREW, MACHINE(STOP ARM-H/B)
6   HINGE ASSY H/BAR
12   SCREW MACHINE(HINGE-H/B)
Page of 127
Display

Click on the first or last page to see other GR-267 service manuals if exist.