DOWNLOAD LG GR-267 Service Manual ↓ Size: 22.52 MB | Pages: 127 in PDF or view online for FREE

1) Loosen two screws after disconnecting a cap screw of a

grille fan(U) with a balde screwdriver.

2) Disassembly of a grille fan(U) : Pull forward after

opening hook at 

➝

part with a balde screwdriver.

3) Disconnect housing  A  of a grille fan (L) from the main

body.

4) Disassembly of a grille fan (L) : Hold  upper part of a

grille fan(L) and pull forward carefully.

5) Loosen two screws.

6) Disassembly of shroud. F(U) : Disconnect housing of  B

after removing two rail guides with a balde screwdriver. 

7) Disassembly of shroud. F(U) : Hold upper part and pull

forward.

8) Check foam PU sticking conditions around a shroud,

F(U) and F(L)  during assembling.  If damaged, torn or
badly sticked, assemble with a new one after sealing
well.

1) Disconnection of Cover Lamp, R(U) : Loosen one screw

in the center with a phillips screwdriver after pushing two
rail guides on the lower part of a control box, R with a
balde screwdriver, and pull a cover lamp, R(U) forward. 

2) Loosen four screws in  A  after taking out a lamp.  Hold

a lower part of control box and take out a control box by
pulling forward and disconnect housing  B  from the
main body.

1) Loosen four screws in 

a

and remove cover PWB by

pulling up in arrow direction.

2) When disassembling the whole case PWB, disassemble

all housings first and push a case PWB in arrow
direction to disassemble from the main body.  

3) When disassembling Main PWB Assy. and Sub. PWB

Assy from a case PWB, open each hook and
disconnect.

- 96 -

A

B

Shroud ,F(U)

Grille Fan(U)

Grille Fan(L)

Shroud ,F(L)

Cap,Screw

Cover Lamp,R(U)

A

B

1

PWB Assy, Sup

Case, PWB

PWB Assy, Main

HOUSING

1) How to disassemble:

(1) Remove ice bank from the freezer compartment.

(2) Loosen two screws on the upper part of icemaker

bracket.

(3) Disconnect icemaker bracket so that it can slide

forward.

(4) Disconnect icemaker housing and sensor housing.

(5) Disconnect icemaker horizontally by pressing bracket

hook part. ( Don’t disassemble further. The set value
may be changed.)

2) How to assemble : The assembly is the reverse order of

the above disassembly.  

When the ice tray is not horizontal after assembly,
assembly must be wrong. Check and assemble
again.

1) How to disassemble:

(1) Remove ice tray assy from the freezer compartment.

(2) Pull out knob from the ice tray in arrow direction.

(At this time, pull out a knob in arrow direction while
shaking right and left as the knob is connected to
pins in  A .)

(3) Spring can be removed by pulling ice tray in arrow

direction and pulling out a spring inserted in ice tray
axis from the hole of supporter ice tray.

2) How to assemble : Assembly is the reverse order of

disassembly.

It is important to put one end of spring into the hole
of the supporter ice tray and the other end on the
lower part of an ice tray when inserting spring into
the shaft.

- 97 -

Bracket, Ice Maker

Hook

Ice Maker Unit

Lever

Tray, Ice

Sensor

Insulation

Cover, Sensor

Supporter Ice Tray

Pin

Knob

Ice Tray

Spring

1) Disconnect button assembly by pulling down until it

stops and then pulling forward.

2) Remove display frame Assy by making a gap between a

display frame Assy. and funnel Assy. with a balde
screwdriver and pulling it forward. The cover dispenser
is fixed with a hook. 

3) Display Assy can be disconnected by pressing the

upper part of a cover dispenser and pushing a display
Assy. after disconnecting display frame Assy. housing.

4) Loosen four screws with a phillips screwdriver and pull a

funnel Assy to disconnect.

5) Duct cap Assy is disconnected if hold lever connecting

screw is loosened with a phillips screwdriver.

6) For assembling a duct cap Assy., insert one end of a

spring into the right hole of dispenser lever, and insert
the other end into the right hole in upper part of
dispenser. And then assemble a holder lever after fixing
a holder at a solenoid Assy working part. 

- 98 -

Button

Funnel Assy

Funnel
Assy

Holder

Lever

Solenoid Assy

Cap 

Spring

Heater, Sheet

Lever,Dispenser

Solenoid Assy

7) Dispenser Related Parts

- 99 -

15

17

14

2

4

5

3

1

6

22

24

23

21

13

12

7

16

18

21

19

9

10

8

11

1

FRAME ASSY, DISPLAY

2

COVER, DISPENSER

3

COVER, DISPLAY

4

PWB(PCB) ASSY, DISPLAY

5

BUTTON(DISPLAY)

6

DECO, DISPENSER

7

FUNNEL ASSY

8

SWITCH, MICRO

9

FRAME, FUNNEL

10 LEVER(SWITCH)

11 FUNNEL

12 RUBBER, FUNNEL

13 COVER, LAMP

14 SOLENOID ASSY

15 SPRING

16 HOLDER, LEVER

17 CAP, DUCT

19 LEVER, DISPENSER

20 RUBBER, CAP

21 BUTTON ASSY

22 BUTTON

23 HOLDER, BUTTON

24 DECO, DRAIN