LG MC-7682W Service Manual ▷ View online
4-2
OPERATING SEQUENCE
The following is a description of component functions
during oven operation.
during oven operation.
1. SETTING THE CLOCK
2. MICROWAVE COOKING
3. GRILL COOKING
4. CONVECTION COOKING
To pre-heat
To cook
5. COMBINATION COOKING
To Grill Combi
To Convection Combi
6. AUTO WEIGHT DEFROST
7. AUTO ROAST
8. AUTO COOK
9. QUICK START
10. MORE AND LESS
Clock
Desired
minute
Start
Desired
hour
Stop/
Clear
Function
MWO
Stop/Clear
Desired
power
level
Start
Desired
cooking
time
Start
Stop/
Clear
Function
Grill
Desired
cooking
time
Desired
cooking
time
Start
Stop/Clear
Start
Stop/
Clear
Dial
(Turn right and left)
Desired
auto cook
Stop/Clear
Stop/Clear
Function
Combi-1
Desired
defrost
category
Food
weight
Start
Stop/Clear
Desired
Auto Roast
category
Start
Stop/Clear
Desired
auto cook
category
Food
weight
Start
Start
Stop/
Clear
Function
Convection
Desired convection
temp
(40˚C, 100˚C~250˚C)
Start
Stop/
Clear
Function
Convection
Desired convection
temp
(40˚C, 100˚C~250˚C)
Start
Start
Desired
cooking time
Stop/
Clear
Function
Combi-1
Desired
cooking
time
Desired convection
temp
(40˚C, 100˚C~250˚C)
Start
Start
SCHEMATIC DIAGRAM
4-3
CIRCUIT DESCRIPTION
GENERAL DETAILS
• The low voltage transformer supplies the necessary
voltage to the micom controller when power cord is
plugged in.
plugged in.
• When the door is closed, the primary switch is ON, the
secondary switch is ON, and the monitor switch opens
(contact COM and NO).
(contact COM and NO).
WHEN SELECTING COOKING POWER
LEVEL AND TIME
• The micom controller memorizes the function you set.
• The time you set appears in the display window.
• Each indicator light turns on to indicate that the stage
• The time you set appears in the display window.
• Each indicator light turns on to indicate that the stage
has been set.
WHEN TOUCHING THE START PAD
• The coil of the relay is energized by the micom
controller.
• Power input is supplied to the high voltage transformer
through the fuse to the primary switch and relay 2.
• Turntable rotates.
• The fan motor rotates and cools the magnetron by
blowing the air (coming from the intake on the
baseplate).
baseplate).
• The air is also directed into the oven to exhaust the
vapor in the oven through the upper plate.
• Cooking time starts counting down.
• 3.2 volts AC is generated from the filament winding of
• 3.2 volts AC is generated from the filament winding of
the high voltage transformer. This 3.2 volts is applied to
the magnetron to heat the magnetron filament through
two noise-preventing choke coils.
the magnetron to heat the magnetron filament through
two noise-preventing choke coils.
• A high voltage of approximately 2100 volts AC is
generated in the secondary of the high voltage
transformer which is increased by the action of the high
voltage diode and charging of the high voltage
capacitor.
transformer which is increased by the action of the high
voltage diode and charging of the high voltage
capacitor.
• The negative 4,000 Volts DC is applied to the filament
of the magnetron.
WHEN THE OVEN IS SET AT ANY LEVEL
EXCEPT MAXIMUM.
• The micom controller controls the ON-OFF time of
relay 2 by the applied signal to vary the average output
power of microwave oven as POWER LEVEL.
(refer to page 1-1)
• One complete cycle of relay 2 is 22 seconds.
WHEN THE DOOR IS OPENED DURING
COOKING
• Both the primary switch and relay 2 are cut off primary
winding voltage of the high voltage transformer.
• ON-OFF of relay 2 is coupled electrically with opening
and closing of the secondary switch.
• When the door is opened, the secondary switch is
opened and when the door is closed, the secondary
switch is closed.
switch is closed.
• The cooking time stops counting down.
• Relay stops functioning.
• As the door is opened, if the contact of primary switch
• Relay stops functioning.
• As the door is opened, if the contact of primary switch
fails to open, the fuse opens due to the large current
surge caused by the monitor switch activation, which in
turn stops magnetron oscillation.
surge caused by the monitor switch activation, which in
turn stops magnetron oscillation.
WHEN TOUCHING THE START KEY
WITH THE GRILL COOKING FUNCTION
SELECTED
• The contacts of the primary switch and the secondary
switch close the circuit.
• A.C. voltage is applied to the grill heater through grill
thermostat as shown by the solid line.
• Turntable rotates.
• The fan motor rotates.
• The air is also directed into the oven to exhaust the
• The fan motor rotates.
• The air is also directed into the oven to exhaust the
vapor in the oven through the base plate and upper
plate.
plate.
4-4
L
FUSE
H.V.
TRANS-
FORMER
RELAY 2
MICOM CONTROLLER
SECONDARY
SWITCH
SWITCH
PRIMARY
SWITCH
N
MONITOR
SWITCH
L
FUSE
H.V.
TRANS-
FORMER
RELAY 2
MICOM CONTROLLER
SECONDARY
SWITCH
SWITCH
PRIMARY
SWITCH
N
MONITOR
SWITCH
RELAY 3
L
N
GRILL
HEATER
L
G -Y
N
E
8-1
SCHEMATIC DIAGRAM OF P.C.B
Click on the first or last page to see other MC-7682W service manuals if exist.