DOWNLOAD LG LWM1560BHE / LWM1861BHE / LWM1861BHG / LWN1862BHG / LWN2262BHG Service Manual ↓ Size: 2.32 MB | Pages: 67 in PDF or view online for FREE

—10—

1. Remove the fan. (Refer to section 2.2.3)
2. Remove the 2 screws which fasten the shroud.
3. Remove the shroud. (See figure 8)
4. Re-install the component by referring to the

removal procedure, above.

1. Remove the cabinet. (Refer to section 2.1.2)
2. Remove the cover control and disconnect a wire

housing in control box. (Refer to section 2.1.3)

3. Remove the blower. (Refer to section 2.2.2)
4. Remove the fan. (Refer to section 2.2.3)
5. Remove the 4 screws which fasten the motor.

(See figure 9)

6. Remove the motor.
7. Re-install the components by referring to the

removal procedure, above.

1. Remove the cabinet. (Refer to section 2.1.2)
2. Discharge the refrigerant system using Freon

TM

Recovery System.
If there is no valve to attach the recovery system,
install one (such as a WATCO A-1) before venting
the Freon

TM 

. Leave the valve in place after 

servicing the system.

3. Disconnect the 3 leads from the compressor.
4. After purging the unit completely, unbrace the

suction and discharge tubes at the compressor
connections.

5. Remove the 3 nuts and the 3 washers which

fasten the compressor.

6. Remove the compressor. (See figure 10)
7. Re-instill the components by referring to the

removal procedure, above.

—11—

1. Remove the control box. (Refer to section 2.1.3)
2. Remove the screw and knobs which fasten the

display panel.

3. Disconnect the 2 leads from the rocker switch.
4. Disconnect the lamp lead from the terminal block

and remove the panel.

5. Remove a screw and unfold the control box. 

(See figure 11)

6. Remove the screw and the clamp which fastens

the capacitor. (See figure 11)

7. Disconnect all the leads of capacitor terminals.
8. Re-install the components by referring to the

removal procedure, above.

1. Remove the control box. (Refer to section 2.1.3)
2. Unfold the control box. (Refer to section 2.3.3)
3. Disconnect the grounding screw from the control

box.

4. Disconnect 2 receptacles.
5. Remove a screw which fastens the clip cord.
6. Pull the power cord. (See figure 12)
7. Re-install the component by referring to the

removal procedure, above.
(Use only one ground-marked hole      for ground
connection.)

8. If the supply cord of this appliance is damaged, it

must be replaced by the special cord. 
(The special cord means the cord which has the
same specification marked on the supply cord
fitted to the unit.)

1. Remove the control box. (Refer to section 2.1.3)
2. Unfold the control box. (Refer to section 2.3.3)
3. Remove the 2 screws which fasten the thermostat.
4. Disconnect all the leads of thermostat terminals.
5. Remove the thermostat. (See figure 13)
6. Re-install the components by referring to the

removal procedure, above.

1. Remove the control box. (Refer to section 2.1.3)
2. Unfold the control box. (Refer to section 2.3.3)
3. Remove 2 screws which fasten the rotary switch.
4. Disconnect all the leads of the rotary switch

terminals.

5. Remove the rotary switch. (See figure 14)
6. Re-install the components by referring to the

above removal procedure, above.

1. Remove the control box. (Refer to section 2.1.3)
2. Unfold the control box. (Refer to section 2.3.3)
3. Remove the cam.
4. Disconnect all the leads of the synchronous

motor.

5. Remove the 2 screws which fasten the

synchronous motor. (See figure 15)

6. Re-install the components by referring to the

removal procedure, above.

1. Remove the cabinet. (Refer to section 2.1.2)
2. Remove the reversing coil from the reversing valve

assembly by loosening the screw.

3. Discharge the refrigerant system using a Freon

TM

recovery system.
If there is no valve to attach the recovery system,
install one (such as a WATCO A-1) before venting
the Freon

TM

.

Leave the valve in place after servicing.

4. After discharging the refrigerant completely,

unbraze the interconnecting tube at the reversing
vlave assembly connections.

5. Re-install the components by referring to the

removal procedure, above.

When connect the reversing valve assembly,
braze the reversing valve and inter-connecting
tube immersing in water not to make the tempera-
ture of surface exceed more than 120°C(248°F)

—12—

Reversing valve

Reversing coil

—13—

1. Remove the cabinet. (Refer to section 2.1.2)
2. Remove the brace and the shroud cover.

(Refer to section 2.2.1)

3. Remove 6 screws which fasten the condenser.
4. After discharging the refrigerant completely,

unbraze the interconnecting tube at the condenser
connections.

5. Remove the condenser.
6. Re-install the components by referring to notes.

(See figure 17)

1. Remove the cabinet. (Refer to section 2.1.2)
2. Remove the top cover and the brace. 

(Refer to section 2.2.1)

3. Discharge the refrigerant completely.
4. Remove the 3 screws which fasten the evaporator

at the left side and the top side.

5. Move the evaporator sideward carefully and then

unbraze the interconnecting tube at the evaporator
connectors.

6. Remove the evaporator.
7. Re-install the components by referring to notes.

(See figure 18)

1. Remove the cabinet. (Refer to section 2.1.2)
2. Remove the brace. (Refer to section 2.2.1)
3. After discharging the refrigerant completely,

unbraze the interconnecting tube at the capillary
tube.

4. Remove the capillary tube.
5. Re-install the components by referring to notes.

Discharge the refrigerant system using Freon

TM

Recovery System.
If there is no valve to attach the recovery system,
install one (such as a WATCO A-1) before
venting the Freon

TM

. Leave the valve in place

after servicing the system.