LG LWH0560ACG_ACL Service Manual ▷ View online
3828AR3735S —2—
S : Service Parts
O : Non Service Parts
O : Non Service Parts
LWH0560ACG
LOCATION NO.
No.
DESCRIPTION
PART No.
Q'TY
REMARKS
264110
268770
269310
266003
W48601
W0CZZ
235000
W1NFZ
W1NZZ
567502
554160
W1NHA
548100
550140
352100
552111
35211A
354210
W48602
359012
152380
130410
A – 1
POWER CORD ASSY
1
S
2
CLIP
1
S
3
LEAD WIRE ASSY
1
S
4
CONDUCTOR ASSY
1
S
5
THERMOSTAT ASSY
1
S
6
SWITCH, ROTARY
1
S
7
CLAMP, CAPACITOR
1
S
8
CAPACITOR
1
S
9
BOARD, CONTROL (INDOOR)
1
S
10
CONDUCTOR ASSY
1
S
B – 1
NUT, HEXAGON FLANGE
1
O
2
NUT
1
O
3
COVER, TERMINAL
1
O
4
OVERLOAD PROTECTOR SPRING
1
O
5
O.L.P
1
O
6
GASKET
1
O
7
COMPRESSOR
1
S
8
NUT HEXAGON (1)
3
O
9
BRACKET, WASHER
3
O
10
ISOLATOR, COMP
3
O
C – 1
TUBE EVAPORATOR
1
S
2
TUBE ASSY, CAPILLARY
1
S
3
TUBE ASSY, SUCTION INDOOR
1
S
4
TUBE, DISCHARGE
1
S
D – 1
EVAPORATOR ASSY
1
S
2
CLAMP, SPRING
2
S
3
FAN ASSY, BLOWER
1
S
4
AIR GUIDE
1
S
5
SCROLL
1
S
6
BASE ASSY, SINGLE
1
S
2H01580M
4H01254A
6877A20001A
6631AR3843K
2H01109H
2H00154H
4H00442N
6120AR2194H
4994AR2149A
2H01045E
4H00947A
4H01058A
3550U-L002D
4970U-L002A
6750U-L047A
4986U-L001B
5416A20001E
1NHA0801206
4810AR4155B
5040AR4195A
5210A30124A
5211AR3332N
5211AR6204E
5210A30001C
5421A20024A
3H02932B
5834AR1592A
5238AR1591A
3072AR1589A
3041AR6199J
3828AR3735S —3—
LOCATION NO.
No.
DESCRIPTION
PART No.
Q'TY
REMARKS
149980
559011
554030
349480
130910
149410
135313
152302
135312
159902
159902
145200
D – 7
MOTOR ASSY
1
S
8
SHROUD
1
S
9
FAN ASSY, AXIAL
1
S
10
CONDENSER ASSY
1
S
11
ORIFICE
1
S
12
DRAIN, HOLE
1
O
WASHER, PLAIN
1
S
E - 1
CABINET ASSY, SINGLE
1
S
F - 1
KNOB ASSY
2
S
2
GRILLE ASSY, INLET
1
S
3
FILTER(MECH), A/C
1
S
4
GRILLE ASSY, FRONT
1
S
5
VANE, VERTICAL
2
S
6
VANE, VERTICAL
6
S
7
LINK
2
S
4681AR20001B
4998AR1608A
5900AR1594A
5403AR6200A
4948AR6166A
3H02773A
4H01029E
3091AR6055G
4941AR7315A
3530AR1616A
5231AR2148A
3530AR1615A
5990AR3190A
5990AR3190B
4520AR3191A
—5—
2. DISASSEMBLY INSTRUCTIONS
2.1 MECHANICAL PARTS
2.1.1 FRONT GRILLE
1. Disconnect the unit from the power source.
2. Remove the two knobs by pulling them off.
2. Remove the two knobs by pulling them off.
Using a screwdriver, remove the screw that
secures the front grille to control board.
(See Figure 1)
secures the front grille to control board.
(See Figure 1)
3. Push the front grille up from the bottom.
Pull the top of the front grille away from the
cabinet as the top tabs lift out of their slots.
(See Figure 2)
cabinet as the top tabs lift out of their slots.
(See Figure 2)
4. Replace the grille by placing the tabs in the slots
and push the grille until it snaps into place.
2.1.2 CABINET
1. Disconnect the unit from the power source.
2. Remove the front grille. (Refer to Section 2.1.1)
3. Remove 6 screws that secure the cabinet to the
2. Remove the front grille. (Refer to Section 2.1.1)
3. Remove 6 screws that secure the cabinet to the
base pan. (See Figure 3)
4. Lift the cabinet from the unit.
5. Re-install by referring to the procedures above.
5. Re-install by referring to the procedures above.
2.1.3 CONTROL BOARD
1. Disconnect the unit from the power source.
2. Remove the front grille. (Refer to Section 2.1.1)
3. Remove the cabinet. (Refer to Section 2.1.2)
4. Remove 2 screws that secure the control board to
2. Remove the front grille. (Refer to Section 2.1.1)
3. Remove the cabinet. (Refer to Section 2.1.2)
4. Remove 2 screws that secure the control board to
base pan and orifice. (See Figure 4)
5. Pull the control board toward yourself.
6. Disconnect one housing terminal and 3 wires for
the fan motor and compressor. (See Figure 5)
7. Re-install components by referring to procedures
above. (Refer to wiring diagram on page 20 in this
manual or inside control board.)
manual or inside control board.)
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
NOTE : Controls, wires, and capacitor are now
accessible for servicing. Discharge the
capacitor before servicing.
capacitor before servicing.
—6—
2.2 AIR HANDLING PARTS
2.2.1 ORIFICE
1. Disconnect the unit from the power source.
2. Remove the front grille. (Refer to Section 2.1.1)
3. Remove the cabinet. (Refer to Section 2.1.2)
4. Remove the control board.
2. Remove the front grille. (Refer to Section 2.1.1)
3. Remove the cabinet. (Refer to Section 2.1.2)
4. Remove the control board.
(Refer to Section 2.1.3)
5. Remove 2 screws that secure the orifice.
(See Figure 6)
6. Lift orifice upward.
7. Re-install by referring to the procedures above.
7. Re-install by referring to the procedures above.
2.2.2 BLOWER WHEEL, FAN AND SHROUD
1. Disconnect the unit from the power source.
2. Remove the front grille. (Refer to Section 2.1.1)
3. Remove the cabinet. (Refer to Section 2.1.2)
4. Remove the control board.
2. Remove the front grille. (Refer to Section 2.1.1)
3. Remove the cabinet. (Refer to Section 2.1.2)
4. Remove the control board.
(Refer to Section 2.1.3)
5. Remove the orifice. (Refer to Section 2.2.1)
6. Remove the screw that secures shroud and air
6. Remove the screw that secures shroud and air
guide. (Figure 7)
7. Remove 2 screws that secure the base pan.
(See Figure 8)
8. Remove the screw that secures the shroud to
channel of condenser.
9. Press the snap area of shroud with your thumbs.
This allows you to remove it from the condenser.
10. Lift the compressor upward with the evaporator
and condenser. (See Figure 8)
11. Remove the clamp springs which are clamped to
the boss of fan and blower wheel by hand plier.
(See Figure 9)
(See Figure 9)
12. Pull the fan and blower wheel outward tilting it
foward yourself.
13. Remove the shroud.
14. Re-install by referring to the procedures above.
14. Re-install by referring to the procedures above.
Figure 6
Figure 7
Figure 8
Figure 9