DOWNLOAD LG LWG0760ACG / LWG0760ACG / LWG0760BCG / LWG0960ACG / LWG0960BCG Service Manual ↓ Size: 912.23 KB | Pages: 29 in PDF or view online for FREE

—14—

Equipment needed: Vacuum pump, Charging cylinder,  Manifold gauge, Brazing equipment. Pin-off tool capable
of making a vapor-proof seal, Leak detector, Tubing cutter, Hand Tools to remove components, Service valve.

A

COMPOUND GAUGE

EVAPORATOR
(LOW PRESSURE SIDE)

COMPRESSOR

CAPILLARY TUBE

CONDENSER
(HIGH PRESSURE SIDE)

SEE INSETS

BELOW

MANIFOLD

GAUGE

B

A

B

EXTERNAL
VACUUM PUMP

A

CHARGING
CYLINDER

LOW

HI

B

C

—15—

1.To prevent vibration and noise, make sure the unit

is installed securely and firmly.

2.Install the unit where the sunlight does not shine

directly on the unit.

3.The outside of the cabinet must extend outward for

at least 11" and there should be no obstacles, such
as a fence or wall, within 20" from the back of the
cabinet because it will prevent heat radiation of the
condenser.
Restriction of outside air will greatly reduce the
cooling efficiency of the air conditioner.

4.Install the unit a little slanted so the back is slightly

lower than the front (about 

1

/

2

"). This will help force

condensed water to the outside.

5.Install the unit from the bottom about 30"~60"

above the floor level.

The setting conditions must be checked prior to
initial starting.
The undermentioned items are especially important
checking points when the installation is finished.

1. Grounding wire (Green or Green and Yellow) is

provided in the power cord. The green wire must
be grounded.

2. Connect to a single-outlet 15A circuit.
3. To avoid vibration or noise, make sure the air

conditioner is installed securely.

4 Avoid placing furniture or draperies in front of the

air inlet and outlet.

The air conditioner must be installed horizontally or
tilted slightly to the outside for proper water
drainage.
On exceptionally hot and humid days the air
conditioner may overflow condensed water.
If the air conditioner is used in a hot and high
humidity zone, exchange the 

¥L

HOLE RUBBER

for the 

¥M

DRAIN PIPE.(See figure 18, figure 19.)

All side louvers of the cabinet must remain
exposed to the outside of the structure.

AWNING

COOLED AIR

HEAT

RADIATION

30"~60"

ABOUT 

1

/

2

"

Over 20"

FENCE

BASE PAN

HOLE RUBBER

DRAIN PIPE

1

BOTTOM

2

BASE PAN

BOTTOM

—16—

1. Before installing the room air conditioner, please

install the knob. (If it is not fixed on the unit.)

2. Remove the screws which fasten the cabinet at

both sides and at the back.

3. Slide the unit from the cabinet by gripping the base

pan handle and pulling forward while 
bracing the cabinet.

4. Slide the air conditioner into the case.

Reinstall the 2 screws removed earlier on each side
of the case.

CAUTION: The power cord must be connected to an independent

circuit. The green wire must be grounded.

5. Stuff the foam between the top of the unit and the

wall to prevent air and insects from getting into the
room.

6. Attach the front grille to the case by inserting the

tabs on the grille into the slots on the front of the
case. Push the grille in until it snaps into place.

When you detach the front grille from the case,
push the grille to your right side and pull it toward
you.

7. Lift the inlet grill and secure the front grille with a

screw. Lower the inlet grille into place.
(In case of some models, you can secure the front grille
from the right side or lower side.)

Shipping

screws

—17—

1. If you want to pull out the filter upward, open the

inlet grille slightly. Turn inside out the front grille.
Disassemble the inlet grille from the front grille
with separating the hinged part by inserting a "—"
type screw-driver tip.
Rotate the inlet grille 180 degrees and insert the
hooks into the lower holes of front grille.
Then, insert the filter (See Figure 25, 26)

2. Attach the front grille to the cabinet by inserting the

tabs on the grille into the tabs on the front of the
cabinet. Push the grille in until it snaps into place.
(See Figue 27)

3. Lift the inlet grille and secure it with a type A screw

through the front grille.
(See Figure 28)

4. If you want to pull out the filter downward, use the

reversible inlet grille without change.
(The grille is already assembled for that way.)

Inlet Grille