DOWNLOAD LG LWC1260ACG Service Manual ↓ Size: 3.43 MB | Pages: 127 in PDF or view online for FREE

—13—

1. Remove the front grille. (Refer to section 2.1.1)

2. Remove the cabinet. (Refer to section 2.1.2)

3. Remove the control box. (Refer to section 2.1.3)

4. Remove the 4 screws which fasten the brace.

5. Remove the brace.

6. Remove the 2 screws which fasten the evaporator.

7. Move the evaporator high side forward and pulling

it upside slightly. (See Figure 4)

8. Move the evaporator sideways carefully. 

9. Pull out upside hook of orifice by pushing the tabs

and remove it. (See Figure 5)

10. Remove the clamp with hand plier which secures

the blower.

11. Remove the blower.
12. Remove the 4 screws which fasten the air guide

from the barrier.

13. Move the air guide backward and pulling out from

the base pan

14. Re-install the components by referring to the

removal procedure, above. 

1. Remove the cabinet. (Refer to section 2.1.2)

2. Remove the brace (Refer to section 2.2.1)

3. Remove the 4 screws which fasten the condenser.

4. Move the condenser sideways carefully.

5. Remove the clamp which secures the fan.

6. Remove the fan. (See Figure 6)

7. Re-install by referring to the removal procedure. 

—14—

1. Remove the fan. (Refer to section 2.2.2)
2. Remove the screw which fastens the shroud.

3. Remove the shroud. (See Figure 7)

4. Re-install the component by referring to the

removal procedure, above.

1. Remove the cabinet. (Refer to section 2.1.2)

2. Remove the nut which fastens the terminal cover.

3. Remove the terminal cover. (See Figure 8)

4. Remove all the leads from the overload protector.

5. Remove the overload protector.

6. Re-install the component by referring to the

removal procedure, above. 

1. Remove the cabinet. (Refer to section 2.1.2)

2. Discharge the refrigerant system using a Freon

TM

Recovery System.
If there is no valve to attach the recovery system,
install one (such as a WATCO A-1) before venting
the Freon

TM

. Leave the valve in place after 

servicing the system.

3. Remove the overload protector. (Refer to section

2.3.1)

4. After purging the unit completely, unbraze the

suction and discharge tubes at the compressor
connections.

5. Remove the 3 nuts and the 3 washers which 

fasten the compressor.

6. Remove the compressor. (See Figure 9)

7. Re-install the components by referring to the

removal procedure, above.

—15—

1. Remove the control box. (Refer to section 2.1.3)
2. Remove the knobs and the screw which fasten

control panel from control box.

3. Remove the screw which located in the front.
4. Open the bottom side of control box.
5. Remove the screw and the clamp which fastens

the capacitor.

6. Disconnect all the leads of capacitor terminals.
7. Re-install the components by referring to the

removal procedure, above. (See Figure 10)

1. Remove the control box. (Refer to section 2.1.3)
2. Open the control box. (Refer to section 2.3.3)
3. Disconnect the grounding screw from the control

box.

4. Disconnect the 2 receptacles.
5. Remove a screw which fastens the clip cord. 

(See Figure 11)

6. Remove the power cord. 
7. Re-install the component by referring to the above

removed procedure, above.
(Use only one ground-marked hole      for ground
connection.)

8. If the supply cord is damaged, it must be replaced

by a special cord or assembly available from the
manufacturer or its service agent.

1. Remove the control box. (Refer to section 2.1.3)
2. Open the control box. (Refer to section 2.3.3)
3. Remove the 2 screws which fasten the thermostat.
4. Disconnect 2 leads of thermostat terminals.
5. Remove the thermostat.
6. Re-install the components by refereing to the

above removal procedure. (See Figure 12)

1. Remove the control box. (Refer to section 2.1.3)
2. Open the control box. (Refer to section 2.3.3)
3. Remove the 2 screws which fasten the rotary

switch.

4. Disconnect all the leads of the rotary switch

terminals.

5. Remove the rotary switch.
6. Re-install the components by referring to the

above removal procedure. (See Figure 13)

—16—

1. Remove the cabinet. (Refer to section 2.1.2)
2. Remove the evaporator. (Refer to section 2.2.1)
3. Remove the orifice. (Refer to section 2.2.1)
4. Remove the blower. (Refer to section 2.2.1)
5. Remove the fan. (Refer to section 2.2.2)
6. Remove the control box cover and disconnect 5 or

4 wires of motor housing. (Refer to section 2.1.3)

7. Remove the 4 screws which fasten the motor from

the mount motor. (See Figure 14.)

8. Remove the motor.
9. Re-install the components by referring to the

removal procedure, above.(See Figure 14.)

1. Remove the cabinet. (Refer to section 2.1.2)
2. Remove the 4 screws which fasten the

brace.(Refer to section 2.2.1)

3. Remove the 5 screws which fasten the condenser

and shroud.

4. After discharging the refrigerant completely,

unbraze the interconnecting tube at the condenser
connections.

5. Remove the condenser.
6. Re-install the component by referring to notes.

(See Figure 15)

1. Remove the cabinet. (Refer to section 2.1.2)
2. Remove the 2 screws which fasten the evaporator.
3. Move the evaporator sideways carefully.

(Refer to section 2.2.1)

4. After discharging the refrigerant completely,

unbraze the interconnecting tube at the evaporator
connections.

5. Remove the evaporator.
6. Re-install the component by referring to notes.

(See Figure 16)

Discharge the refrigerant system using a
Freon

TM

Recovery System.

If there is no valve to attach the recovery 
system, install one (such as a WATCO A-1)
before venting the Freon

TM

. Leave the valve in

place after servicing the system.