DOWNLOAD LG LWC1260ACG Service Manual ↓ Size: 3.43 MB | Pages: 127 in PDF or view online for FREE

—18—

1.To prevent vibration and noise, make sure the unit

in installed securely and firmly.

2.Install the unit where the sunlight does not shine

directly on the unit.

3.The outside of the cabinet must extend outward for

at least 12" and there should be no obstacles, such
as a fence or wall, within 20" from the back of the
cabinet because it will prevent heat radiation of the
condenser.
Restriction of outside air will greatly reduce the
cooling efficiency of the air condditioner.

4.Install the unit a little slanted so the back is slightly

lower than the front (about 

1

/

2

"). This will force con-

densed water to the outside.

5.Install the unit with the bottom about 30"~60" above

the floor level.

The setting conditions must be checked prior to
initial starting.
The undermentioned items are especially important
checking points when the installation is finished.

1. Grounding wire (Green or Green and Yellow) is

provided in the power cord. The green wire must
be grounded.

2. Connect to a single-outlet 15AMP circuit.
3. To avoid vibration or noise, make sure the air

conditioner is installed securely.

4 Avoid placing furniture or draperies in front of the

air inlet and outlet.

The air conditioner must be installed level or tilted
slightly to the outside for proper water drainage.
On exceptionally hot and humid days the air
conditioner may drain condensation through
overflow.
If the air conditioner is used in hot and a high
humidity zone, exchange the 

¥L

HOLE RUBBER

for the 

¥M

DRAIN PIPE.(See figure 19, figure 20.)

All side louvers of the cabinet must remain
exposed to the outside of the structure.

AWNING

COOLED AIR

HEAT

RADIATION

30"~60"

ABOUT 

1

/

2

"

Over 20"

FENCE

BASE PAN

HOLE RUBBER

DRAIN PIPE

1

BOTTOM

2

BASE PAN

BOTTOM

—19—

This unit is designed for installation in 
standard double hung windows with actual opening
widths from 27" to 39".
The top and bottom window sash must open
sufficiently to allow a clear vertical opening of 16"
from the bottom of the upper sash to the window
stool.

A

B

D

E

F

C

H

2

3

1

4

2

1

A

RIGHT SIDE

HORIZONTAL
LINE

B

1. WINDOW (WIDTH-A, HEIGHT-B)
2. GASKET
3. WALL

4. DETAILS 5.1 x 30 ROUND HEAD WOOD

SCREWS

A

B

C

D

E

F

H

I

625mm

392mm

280mm

30mm

0~25mm

OVER 420mm

5~10mm

-5~5mm

(24

5

/

8

")

(15

7

/

16

")

(11

1

/

32

")

(1

1

/

16

")

(0~1")

(OVER 16

17

/

32

")

(

3

/

16

"~

3

/

8

")

(-

3

/

16

"~

3

/

16

")

1

2

3

4

8

9

11

7

6

5

10

13

12

1

FRAME CURTAIN

2

2

SILL SUPPORT

2

3

BOLT

2

4

NUT

2

5

SCREW(TYPE A)

16

6

SCREW(TYPE B)

3

7

SCREW(TYPE C)

5

8

FOAM-STRIP

1

9

FOAM-PE

1

10

UPPER GUIDE

1

11

FOAM-PE

1

12

FRAME GUIDE

2

13

WINDOW LOCKING BRACKET

1

Stool

27" to 39"

16" min

Offset

1/2" to 1

1

/

4

"

Sill

Exterior

Interior wall

23

5

/

8

" min

(Without frame curtain)

—20—

1. Remove the screws which fasten the cabinet at

both sides and at the back.

2. Slide the unit from the cabinet by gripping the base

pan handle and pulling forward while 

bracing the cabinet.

3. Remove EPS Material.

4. Cut the window sash seal to the proper length. Peel

off the backing and attach the foam-pe 

¤

to the

underside of the window sash.

5. Remove the backing from the top upper guide

Foam PE 

¤æ

and attach it to the bottom of the upper

guide 

¤ .

6. Attach the upper guide onto the top of the cabinet

with 3 type A screws.

7. Insert the frame guides 

¤

into the bottom of the

cabinet.

8. Insert the Frame Curtain 

¤

into the upper guide 

¤

and frame guides 

¤

.

9. Fasten the curtains to the unit with 4 Type A

screws.

1. Open the window. Mark a line on center of the

window stool(or desired air conditioner 
location).
Carefully place the cabinet on the window stool and
align the center mark on the bottom front with the
center line marked in the window stool.

2. Pull the bottom window sash down behind the

upper guide until it meets.

NOTE: 
• Do not pull the window sash down so tightly that the

movement of Frame Curtain is restricted.

9

10

11

10

5

5

5

12

12

(Type A)

Window stool

Upper guide 

¤

Window Sash

Foam-pe 

¤

Cabinet

Frame Curtain 

¤

Foam-pe 

¤æ

Front Angle

Upper Guide

(Type A)

Shipping screws

EPS Material

—21—

3. Loosely assemble the sill support using the parts

in 

Figure 

23.

4. Select the position that will place the sill 

support near the outer most point on sill
(See 

Figure 

24)

NOTE: Be careful when you install the cabinet (frame

guides 

¤

are broken so easily).

5. Attach the sill support to the cabinet track hole in

relation to the selected position using 
2 Type A screws in each support(See 

Figure 2

4).

6. The cabinet should be installed with a very slight

") downward toward the outside (See

Figure 

25).

Adjust the bolt and the nut of sill support for
balancing the cabinet.

7. Attach the cabinet to the window stool by 

driving the screws 

¤

(Type B: Length sixteen

millimeters and below.) through the front angle into
window stool.

8. Pull each Frame curtain fully to each window sash

track, and repeat step 2.

9. Attach each Frame curtain the window sash using

screws 

¤

(Type C).

(See 

Figure

26)

Sill Support 

¤Ł

Nut 

¤Œ

Screw(Type A)

¤º

Screw(Type B)

¤

Screw(Type B)

¤

Sash track

Front Angle

Type C

¤

Sill support 

¤Ł

Sill support 

¤Ł

¤

Frame Guide

Cabinet

About 

1

/

2

"

About 

1

/

2

"

Bolt 

¤Ø

OUTDOOR

OUTDOOR

INDOOR

INDOOR