DOWNLOAD LG LV-B1861HL Service Manual ↓ Size: 2.17 MB | Pages: 61 in PDF or view online for FREE

–31–

The pipe can be connected to right side,  bottom

or back of the unit.

• After bending an end of the connecting tube, align the

center of the pipings and sufficiently tighten the flare
nut with fingers.

• Finally, tighten the flare nut with torque wrench until

the wrench clicks.

• Connect the Drain Hose insulated to the drain outlet.

Drain hose should be go through under the Hose
Bracket as shown in figure 

ƒŁ

.

• Hang the drain hose on the hose hanger and fix it to

the hole of the hose bracket with a screw.

• Remove the knock-out on the bottomside of Inlet Grille
• Align the center of the pipings and sufficiently tighten

the flare nut with fingers.

• Finally, tighten the flare nut with torque wrench until

the wrench clicks.

• Connect the Drain Hose insulated to the drain outlet.
• Hang the drain hose on the hose hanger and fix it to

the hole of cabinet bottom with a screw.

• The drain hose can be connected to not only the

right side but also left side of the unit.

• If the drain hose is connected to the left side, it

should go through the cabinet bottom.

• Hang the drain hose on the hose hanger and fix it to

the hole of cabinet bottom with a screw.

R

R

R

Drain Hose

Drain Hose

Piping

Hose

Bracket

1

3

4

5

2

Hose Hanger

Hose Hanger

Hose
Hanger

BOTTOM

–32–

• Remove the knock-out at the back side of the cabinet.
• After bending an end of the connecting tube, align the

center of the pipings and sufficiently tighten the flare
nut with fingers.

• Finally, tighten the flare nut with torque wrench until

the wrench clicks.

• Connect the Drain Hose insulated to the drain outlet.
• Tape the Drain Hose to the pipings to avoid coming

off the drain-outlet.

• After bending an end of the connecting tube, align the

center of the pipings and sufficiently tighten the flare
nut with fingers.

• Finally, tighten the flare nut with torque wrench until

the wrench clicks.

• Connect the Drain Hose insulated to the drain outlet.
• Tape the Drain Hose to the pipings to avoid coming

off the drain-outlet.

• Align the center of the pipings and sufficiently tighten

the flare nut with fingers.

• Finally, tighten the flare nut with torque wrench until

the wrench clicks.

• Connect the Drain Hose insulated to the drain outlet.

• The drain hose can be connected to not only right

side but also left side of the unit.

Taping

Drain Hose

Piping

Piping

Drain Hose

Connecting

Cable

Drain Hose

Piping

Drain Hose

REAR

BOTTOM

Taping

Taping

–33–

• When tightening the flare nut with torque wrench,

ensure the direction for tightening follows the arrow on
the wrench.   

• To remove air filter, take hold of tab and pull

slightly upwards.

• Spray one or two glasses of water upon the

evaporator.

• Ensure that water flows drain hose of indoor unit

without any leakage.

R

Liquid side piping
(Smaller Dia.)

Gas side piping
(Bigger Dia.) 

Torque wrench

R

Pipe Size      

Torque     

Liquid Side

1/4"

1.8kg·m

3/8"

4.2kg·m

Gas Side

1/2"

5.5kg·m 

5/8"

6.6kg·m 

–34–

1) Remove the Air guide - L by loosening 2

screws after removing the Inlet grille from the
Indoor unit.

2) Connect the wires to the terminals on the con-

trol board individually according to the outdoor
unit connection.

• Ensure that the color of the wires of outdoor

unit and the terminal No. are the same as
those of indoor unit respectively

R

AIR GUIDE-L

INDOOR UNIT

Control

Panel

1

2

Clamp

Terminals on the indoor unit

POWER

INPUT

GN/YL

POWER

INPUT

GN/YL

Terminals on the indoor unit 1(L) 2(N)

3

4

Terminals on the outdoor unit

3

4

Terminals on the outdoor unit

3

4

5

6

7

1(L) 2(N)

3

4

5

6

7

8

• Cooling & Heating type

• Cooling only type

NORMAL CROSS-
SECTIONAL AREA 
• 2.5mm

2

(24K)

• 2.0mm

2

(18K:for the Middle East)

• 1.5mm

2

(18K:for the other area) 

NORMAL CROSS-
SECTIONAL AREA 
• 2.5mm

2

(24K)

• 2.0mm

2

(18K:for the Middle East)

• 1.5mm

2

(18K:for the other area) 

NORMAL
CROSS-
SECTIONAL
AREA
0.75mm

2

The power cord connected to the
indoor unit should be complied with
the following specifications 
(Type H05VV-F(Indoor) 
approved by HAR or SAA).

The power connecting cable
connected between the indoor and 
outdoor unit should be complied 
with the following specifications  
(Type H07RN-F approved by HAR or SAA).

The connecting cable connected
between the indoor and outdoor unit
should be complied with the
following specifications 
(Type H07RN-F approved by HAR or SAA).

Ø8.0mm

Ø10.0mm

Ø8.0mm

Ø10.0mm

Ø6mm

1) Arrange 2 power cables on the control panel.
2) First, fasten the steel clamp with a screw to the inner boss of control panel.
3) For the cooling model, fix the other side of the clamp with a screw strongly.

For the heat pump model, put the 0.75mm

2

cable(thinner cable) on the clamp and tighten it with a plastic clamp to the oth-

er boss of the control panel.

4) In Australia, the length of power supply cord measured from the entry of the power supply cord to the middle of live pin on

the power plug should be over 1.8m.