DOWNLOAD LG LT-B2860HL Service Manual ↓ Size: 2.71 MB | Pages: 64 in PDF or view online for FREE

• The following parts is option.

¤

Hanging Bolt    - W 3/8 or M10, length 650 mm

¤Ł

Nut                   - W 3/8 or M10

¤Ø

Spring Washer - M10

¤Œ

Plate Washer   - M10

• Drill the piping hole on the wall slightly tilted to

the outdoor side using a Ø 70 hole-core drill.

–25–

Wall

5~7mm

Indoor

Outdoor

Set screw of
paper model (4 pieces)

Paper model
for installation

Ceiling board

100mm

Adjust the same height

Ceiling board

Ceiling 

Flat washer for M10

(accessory)

Keep the length of the bolt

from the bracket to 40mm

Open the ceiling board
along the outer edge of the 
paper model

Flat washer for M10

(accessory)

Hanging bolt

(W3/8 or M10)

Nut
(W3/8 or M10)

Nut

(W3/8 or M10)

Spring washer

(M10)

Air Conditioner body

• Tighten the nut and bolt to prevent unit falling.

• Although the room temperature sensor is in the indoor unit, the remote control box should be installed in such

places away from direct sunlight and high humidity.

Installation of the remote control box
• Select places that are not splashed with water.
• Select control position after receiving customer approval.
• The room temperature sensor of the thermostat for temperature control is built in the indoor unit.
• This remote controller equipped with liquid crystal display. If this position is higher or lower, display is difficult

to see.(The standard height is 1.2 ~ 1.5m high)

Routing of the remote control cord
• Keep the remote control cord away from the refrigerant piping and the drain piping.
• To protect the remote control cord from electrical noise, place the cord at least 5cm away from other power

cables (audio equipment, television set, etc.)

• If the remote control cord is secured to a wall, provide a trap at the top of the cord to prevent water droplets

from running.

–26–

Remove the battery cover from the remote con-
troller.
• Slide the cover according to the arrow direction.

Insert the two batteries.
• Be sure that the (+) and (-) directions are correct.
• Be sure that both batteries are new.

Re-attach the cover.
• Slide it back into position.

• Fix the under plate on the wall

• Separate the under plate from Remote control box.

• Fix the cord clamps on the wall by

ø 3 tapping screws (accessory).

• Fix the remote control cord.

Remote control 

box body

Cord clmp
(accessory)

Lever carefully 

the box open 

using a screw 

driver, etc.

Front case

The lower part

Face of wall

Under plate

Screw (accessory)

• Do not use rechargeable bat-

teries, such batteries differ
from standard dry cells in
shape, dimensions, and per-
formance.

• Romove the batteries from the

remote controller if the air con-
ditioner is not going to be used
for some long time.

 

Wire and make sure that teminal

numbers are matched on unit side and

remote controller side.

The maximum length of the cord is 100m.

If the length of the cord exceeds 50m,

use a wire size greater than 0.5mm

2

.

Remote controller

 Yellow, Red, Brown  

(Main board)

CN REMO

–27–

• Open the control box cover and connect the Remote control cord and Indoor power wires.

The power cord connected to the outdoor unit 
should be complied with the following specifications 
(Rubber insulation, type H05RN-F approved by HAR 
 or SAA).

The connecting cable connected to the indoor and 
outdoor unit should be complied with the following 
specifications (Rubber insulation, type H05RN-F 
approved by HAR or SAA).

8.5mm

20mm

GN/YL

Capacity 1 Phase 3 Phase

36K BTU/h 5.5mm

2

2.5mm

2

24,28,30K

BTU/h

2.5mm

2

-

7.5mm

20mm

GN/YL

Remote control
cord

Control 
box cover

Control box cover

fitting screw (4 units)

[Air inlet side view]

Wire taking inlet

Indoor Power wires

Terminal Block of Indoor Unit

3(N) 4(L)

5

6

7

S

R

T

3(N)

N

4(L)

5

6

7

8

Terminal Block of Outdoor Unit

Power Cord

Terminal Block of Indoor Unit

3(N) 4(L)

5

6

7

S

R

T

3(N)

N

4(L)

5

6

7

8

Terminal Block of Outdoor Unit

Power Cord

Terminal Block of Indoor Unit

3(N) 4(L)

5

6

7

1(N) 2(L)

3(N) 4(L)

5

6

7

8

Terminal Block of Outdoor Unit

Power Cord

Terminal Block of Indoor Unit

3(N) 4(L)

5

6

7

1(N) 2(L)

3(N) 4(L)

5

6

7

8

Terminal Block of Outdoor Unit

Power Cord

Make sure that the screws of the terminal are free from looseness.

If the supply cord is damaged, it must be replaced by a special cord or assembly available from
the manufacturer or its service agent.

■

• Cooling Model

■

• Cooling Model

–28–

1. All wiring must comply with LOCAL REGULATIONS.
2. Select a power source that is capable of supplying the current required by the air conditioner.
3. Feed the power source to the unit via a distribution switch board designed for this purpose.
4. The terminal screws inside the control box may be loose due to vibration during transport. 

Check the screws for loose connection. 
(Running the air conditioner with loose connection can overload and damage electrical components.)

5. Always ground the air conditioner with a grounding wire and connector to meet the LOCAL REGULATION.

Main power source

Switch box

Refrigerant pipe

Circuit Breaker

Use a 25A circuit breaker or time delay fuse.