LG LS-J0960NL Service Manual ▷ View online
-16-
7.3 Fuzzy operation for dehumidification
• At the beginning of Fuzzy mode operation, the setting temperature is automatically selected according to the
intake air temperature at that time.
• According to the setting temperature selected by Fuzzy rule, the operating frequency of compressor is
determined like dehumidefication mode operation.
8. Jet cool mode operation
■
For Cooling Only model
• If the Jet Cool key is input at any operation mode while in appliance operation, the Jet Cool mode operates.
• In the Jet Cool mode, the indoor fan is operated at super-high speed for 30 min at cooling mode operation.
• In the Jet Cool mode operation, the room temperature is controlled to the setting temperature, 18°C
• When the sleep timer mode is input while in the Jet Cool mode operation, the Jet Cool mode has the
• In the Jet Cool mode, the indoor fan is operated at super-high speed for 30 min at cooling mode operation.
• In the Jet Cool mode operation, the room temperature is controlled to the setting temperature, 18°C
• When the sleep timer mode is input while in the Jet Cool mode operation, the Jet Cool mode has the
priority.
• When the Jet Cool key is input, the upper/lower vanes are reset to those of the initial cooling mode and
then operated in order that the air outflow could reach further.
■
For Heat Pump model
• While in heating mode or Fuzzy operation, the Jet Cool key cannot be input. When it is input while in the
other mode operation(cooling, dehumidification, ventilation), the Jet Cool mode is operated.
• In the Jet Cool mode, the indoor fan is operated super-high speed for 30 min. at cooling mode operation.
• In the Jet Cool mode, the room temperature is controlled to the setting temperature, 18°C.
• When the sleep timer mode input while the Jet Cool mode operation, the Jet Cool mode has the priority.
• When the Jet Cool key is input, the upper/lower vane is reset to those of the initial cooling mode and then
• In the Jet Cool mode, the room temperature is controlled to the setting temperature, 18°C.
• When the sleep timer mode input while the Jet Cool mode operation, the Jet Cool mode has the priority.
• When the Jet Cool key is input, the upper/lower vane is reset to those of the initial cooling mode and then
operated in order that the air outflow could reach further.
at beginning
during operation
Outdoor temp.
over 26°C
18~26°C
below 18°C
Setting temp.
25°C
intake air temp. -0.5°C
18°C
the same as dehumidification mode
Fan speed
CHAOS airflow
9. Swing mode
9.1 Chaos swing mode of not fuzzy mode operation
• By the Chaos swing key input, the upper/lower vane automatically operates with the Chaos swing or it is fixed
to the desired direction.
Chaos swing
9.2 Auto swing of Fuzzy mode operation
• While in Fuzzy mode operation, Chaos swing is operated according to 1/f fluctuation.
1/f fluctuation
-17-
CLOSED
Open
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
Beginning
of cooling
Mode 8
< Cooling Mode >
8
°
135
°
< Heating Mode >
CLOSED
Open
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
Beginning
of heating
of heating
Mode 8
8
°
135
°
CLOSED
Open
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
Mode 8
8
°
135
°
10. Sleep timer operation
• When the sleep time is reached after [1,2,3,4,5,6,7hr] is input by the remote control while in appliance , the
operation of the appliance stops.
• When the appliance is on pause, the sleep timer mode cannot be input.
10.1 Sleep timer operation for cooling cycle
• While in cooling mode operation, 60 min. later since the start of the sleep timer, the setting temperature
increase by 0.5°C. After another 60min. elapse, it increases by 1°C again.
10.2 Sleep timer operation for heating cycle
• While in heating mode operation, 60 min. later since the start of the sleep timer, the setting temperature
decrease by 0.5°C. After another 60min. elapse, it decreases by 1°C again.
Setting temp, for heating cycle
-18-
Setting temp. (
°
C)
Cooling ON temp.
(Setting temp. +0.5
°
C)
Cooling OFF temp.
(Setting temp. -0.5
°
C)
1
2
Sleep time (hr)
Setting temp. (
°
C)
Heating ON temp.
(Setting temp)
Heating OFF temp.
(Setting temp. +3.0
°
C)
1
2
Sleep time (hr)
10.1 Sleep timer operation for cooling cycle
• While in cooling mode operation, 60 min. later since the start of the sleep timer, the setting temperature
increase by 0.5°C. After another 60min. elapse, it increases by 1°C again.
10.2 Sleep timer operation for heating cycle
• While in heating mode operation, 60 min. later since the start of the sleep timer, the setting temperature
decrease by 0.5°C. After another 60min. elapse, it decreases by 1°C again.
Setting temp, for heating cycle
-18-
Setting temp. (
°
C)
Cooling ON temp.
(Setting temp. +0.5
°
C)
Cooling OFF temp.
(Setting temp. -0.5
°
C)
1
2
Sleep time (hr)
Setting temp. (
°
C)
Heating ON temp.
(Setting temp)
Heating OFF temp.
(Setting temp. +3.0
°
C)
1
2
Sleep time (hr)