DOWNLOAD LG LB-H1860HL / LB-H1860CL / LB-H2460HL / LB-H2460CL Service Manual ↓ Size: 1.61 MB | Pages: 51 in PDF or view online for FREE

–18–

• Select and mark the position for fixing bolts.
• Drill the hole for set anchor on the face of ceiling.

• Insert the set anchor and washer onto the suspen-

sion bolts for locking the suspension bolts on the ceil-
ing.

• Mount the suspension bolts to the set anchor firmly.
• Secure the installation plates onto the suspension

bolts (adjust level roughly) using nuts, washers and
spring washers.

Installation of the remote controller
• Select places that are not splashed with water.
• Select control position after receiving customer approval.
• The room temperature sensor is built in the indoor unit.
• This remote controller equipped with liquid crystal display. If this position is higher or lower, display is difficult

to see.(The standard height is 1.2 ~ 1.5m high)

Routing of the remote controller cord
• Keep the remote controller cord away from the refrigerant piping and the drain piping.
• To protect the remote controller cord from electrical noise, place the cord at least 5cm away from other power

cables (audio equipment, television set, etc.)

• If the remote controller cord is secured to the wall, provide a trap at the top of the cord to prevent water

droplets from running.

Tighten the nut and bolt to prevent unit falling.

1 Set anchor

2 Plate washer
3 Spring washer

4 Nut

5 Suspension
   bolts

• Local supply

➀ 

Set anchor

➁

Plate washer 

- M10

➂

Spring washer

- M10

➃

Nut 

- W3/8 or M10

➄

Suspension bolt

- W3/8 or M10

–19–

Remote control 

box body

Cord clamp
(accessory)

Lever carefully 

the box open 

using a screw 

driver, etc.

Front case

The lo

wer par

t

Face of wall

Under plate

Screw (accessory)

Remove the battery cover from the remote con-
troller.
• Slide the cover according to the arrow direction.

Insert the two batteries.
• Be sure that the (+) and (-) directions are correct.
• Be sure that both batteries are new.

Re-attach the cover.
• Slide it back into position.

• Fix the under plate on the wall

• Separate the under plate from Remote control box.

• Fix the cord clamps on the wall by ø 3 tapping

screws (accessory).

• Fix the remote control cord.

 

Wire and make sure that teminal

numbers are matched on unit side and

remote controller side.

The maximum length of the cord is 100m.

If the length of the cord exceeds 50m,

use a wire size greater than 0.5mm

2

.

Remote controller

(Main board)

CN REMO

• Do not use rechargeable batteries,

such batteries differ from standard dry
cells in shape, dimensions, and per-
formance.

• Romove the batteries from the remote

controller if the air conditioner is not
going to be used for some long time.

–20–

Connect the wires to the terminals on the control board individually according to the
outdoor unit connection.
• Ensure that the color of the wires of outdoor unit and the terminal No. are the same as

those of indoor unit respectively

36K Btu

1) Arrange 2 power cables on the control panel.
2) First, fasten the steel clamp with a screw to the inner boss of control panel.
3) For the cooling model, fix the other side of the clamp with a screw strongly.

For the heat pump model, put the 0.75mm

2

cable(thinner cable) on the clamp and tighten it

with a plastic clamp to the other boss of the control panel.

4) In Australia, the length of power supply cord measured from the entry of the power supply

cord to the middle of live pin on the power plug should be over 1.8m.

Make sure that the screws of the terminal are free from looseness.

POWER INPUT

• Cooling & Heating type

• Cooling only type

(380-415V3N~)

(220-240V~)

Terminals on the indoor unit

1

2

4

5

3

Terminals on the outdoor unit

1

2

4

5

3

POWER
INPUT

POWER
INPUT

• Cooling only type

Terminals on the indoor unit

1(L) 2(N)

4(N) 5

3(L)

Terminals on the outdoor unit

4(N)

5

6

3(L)

1(L) 2(N)

4(N)

5

6

7

8

3(L)

4(N)

5

6

7

3(L)

Terminals on the indoor unit

1

2

4

5

3

• Cooling & Heating type

Terminals on the indoor unit

Terminals on the outdoor unit

Terminals on the outdoor unit

1

2

4

5

3

1(L)

2(N)

POWER INPUT

R

S

T

N

The power cord connected to the outdoor unit should be 
complied with the following specifications (Rubber 
insulation, type H05RN-F approved by HAR or SAA).

If the supply cord is damaged, it must be replaced by a special cord or assembly availible from the manufacturer of its service agent.

The connecting cable connected to the indoor and outdoor 
unit should be complied with the following specifications 
(Rubber insulation, type H05RN-F approved by HAR or SAA).

20mm

GN/YL

20mm

GN/YL

Capacity

18K BTU/h

24K BTU/h

36K BTU/h

1 Phase

2.5mm

2

2.5mm

2

5.5mm

2

3 Phase

-

-

2.5mm

2

18K/24K Btu

–21–

Outdoor

Indoor

Control terminal board

Cord
clamper

Cover control

Main 

power source

Switch box

Circuit Breaker

Main terminal board

view

1

1

Control terminal board

Control box

Control box cover

(On which the Electric

Wiring Connection is put)

Cord clamper

Connection
cord between 
the indoor unit
and the 
outdoor unit

Remote
control cord

Perform the electrical wiring work according to the electrical
wiring connection.

• All wiring must comply with local requirements.
• Select a power source that is capable of supply-

ing the current required by the air conditioner.

• Use a recognized circuit breaker between the

power source and the unit. A disconnection
device to adequately disconnect all supply lines
must be fitted.

• Capacity of circuit breaker

• Remove the control box cover for elec-

trical connection between the indoor
and outdoor unit.(Remove two screws

➀

.)

• Use the cord clamper to fix the cord.

• Remove the control cover for wiring con-

nection.

• Use the cord clamper to fix the cord.
• Earthing work

Connect the cable of diameter 1.6mm

2

or more to the earthing terminal provid-
ed in the control box and do earthing.

Capacity

1 Phase

3 Phase

18K BTU/h

20A

-

24K BTU/h

25A

-

36K BTU/h

35A

25A