DOWNLOAD LG HWC056JWAA0 / W05LC Service Manual ↓ Size: 12.42 MB | Pages: 43 in PDF or view online for FREE

Model
HWC056JWAA0 W05LC
Pages
43
Size
12.42 MB
Type
PDF
Document
Service Manual
Brand
Device
Air Conditioner
File
hwc056jwaa0-w05lc.zip
Date

LG HWC056JWAA0 / W05LC Service Manual ▷ View online

—17—
COMPLAINT
CAUSE
REMEDY
Fan motor noise.
Fan
If cracked, out of balance, or partially missing,
replace it.
Blower
If cracked, out of balance, or partially missing,
replace it.
Loose set screw
Tighten it.
Worn bearings
If knocking sounds continue when running or
loose, replace the motor. If the motor hums or
noise appears to be internal while running,
replace motor.
Compressor will not run,
Voltage
Check voltage. See the limits on the preceding
fan motor runs.
page. If not within limits, call an electrician.
Wiring
Check the wire connections; if loose, repair or
replace the terminal. If the wires are discon-
nected, refer to wiring diagram for identification,
and replace the wires. Check the wire connections;
If not according to the wiring diagram, correct
the connections.
Rotary Switch
Check for continuity, refer to the wiring diagram
for terminal identification. Replace the switch if
the circuit is open.
Thermostat
Check the position of knob. If not at the coldest
setting, advance the knob to this setting and
restart the unit.
Check the continuity of the thermostat. Replace
the thermostat if the circuit is open.
Capacitor (discharge
Check the capacitor.
capacitor before
Replace if not within ±10% of manufacturer’s
servicing.)
rating, replace if shorted, open, or damaged.
Compressor
Check the compressor for open circuit or
ground. If open or grounded, replace the
compressor.
Overload
Check the compressor overload if externally mounted.
Replace if open. (If the compressor temperature is
high, remove the overload, cool and retest.)
Compressor cycles on
Voltage
Check the voltage. See the limits on the
overload.
preceding page. If voltage is not within these limits,
call an electrician.
Overload
Check overload, if externally mounted.
Replace if open. (If the compressor temperature
is high, remove the overload, cool, and retest.)
—18—
COMPLAINT
CAUSE
REMEDY
Compressor cycles on
Fan motor
If not running, determine the cause. Replace if
overload
required.
Condenser air flow
Remove the cabinet, inspect the interior surface
restriction
of the condenser. If restricted, clean carefully
with a vacuum cleaner (do not damage fins) or
brush. Clean the interior base before
re-assembling.
Condenser fins
If the condenser fins are closed over a large
(damaged)
area on the coil surface, head pressures will
increase, causing the compressor to cycle.
Straighten the fins or replace the coil.
Capacitor
Test the capacitor.
Wiring
Check the terminals. If loose, repair or replace.
Refrigeration system
Check the system for a restriction.
Insufficient cooling.
Air filter
If restricted, clean or replace.
Unit undersized
Determine if the unit is properly sized for the
area to be cooled.
Excessive noise.
Blower or fan
Check the set screw, or clamp. If loose or miss-
ing, correct. If the blower or fan is hitting scroll
or shroud, rearrange the air handling parts.
Copper tubing
Remove the cabinet and carefully rearrange the
tubing not to contact the cabinet,
compressor, shroud, and air guide.
5. SCHEMATIC DIAGRAM
19—
5-1. CIRCUIT DIAGRAM
MODEL : HWC056JWAA0
DESCRIPTION & NAME
POWER CORD ASSY
FAN MOTOR
COMPRESSOR
ROTARY SWITCH
THERMOSTAT
CAPACITOR
OVERLOAD PROTECTOR
Q'TY
1
1
1
1
1
1
1
REF. NO
1
2
3
4
5
6
7
5
1
2
6
7
3
4
—2—
CONTENTS
1. PREFACE
.................................................................................................................................................. 3
1.1 FEATURES ................................................................................................................................................... 3
1.2 SPECIFICATIONS ........................................................................................................................................ 3
1.3 LOCATIONS OF CONTROLS ...................................................................................................................... 4
1.4 SAFETY PRECAUTIONS ............................................................................................................................. 4
1.5 INSULATION RESISTANCE TEST .............................................................................................................. 4
2. DISASSEMBLY INSTRUCTIONS
............................................................................................... 5
2.1 MECHANICAL PARTS ................................................................................................................................. 5
2.1.1 FRONT GRILLE ................................................................................................................................... 5
2.1.2 CABINET................................................................................................................................................5
2.1.3 CONTROL BOARD .............................................................................................................................. 5
2.2 AIR HANDLING PARTS ............................................................................................................................... 6
2.2.1 AIR GUIDE UPPER ............................................................................................................................. 6
2.2.2 ORIFICE, TURBO FAN AND FAN ........................................................................................................ 6
2.2.3 MOTOR ................................................................................................................................................. 7
2.2.4 AIR GUIDE............................................................................................................................................ 7
2.3 ELECTRICAL PARTS ................................................................................................................................... 7
2.3.1 OVERLOAD PROTECTOR .................................................................................................................. 7
2.3.2 COMPRESSOR ................................................................................................................................... 7
2.3.3 CAPACITOR ......................................................................................................................................... 8
2.3.4 THERMOSTAT ..................................................................................................................................... 8
2.3.5 ROTARY SWITCH ................................................................................................................................ 8
2.3.6 POWER CORD .................................................................................................................................... 8
2.4 REFRIGERANT CYCLE ................................................................................................................................8
2.4.1 CONDENSER ...................................................................................................................................... 8
2.4.2 EVAPORATOR ..................................................................................................................................... 9
2.4.3 CAPILLARY TUBE ............................................................................................................................... 9
3. INSTALLATION
................................................................................................................................... 11
3.1 SELECT THE BEST LOCATION ................................................................................................................ 11
3.2 CHECK OF INSTALLATION ....................................................................................................................... 11
3.3 HOW TO DRAIN ......................................................................................................................................... 11
3.4 HOW TO INSTALL ...................................................................................................................................... 12
4. TROUBLESHOOTING GUIDE
................................................................................................... 12
4.1 OUTSIDE DIMENSION .............................................................................................................................. 12
4.2 PIPING SYSTEM ....................................................................................................................................... 13
4.3 TROUBLESHOOTING GUIDE ................................................................................................................... 14
5. SCHEMATIC DIAGRAM
................................................................................................................. 19
5.1 CIRCUIT DIAGRAM .................................................................................................................................... 19
6. EXPLODED VIEW
............................................................................................................................. 20
7. SERVICE PARTS LIST
................................................................................................................... 21
Page of 43
Display

Click on the first or last page to see other HWC056JWAA0 / W05LC service manuals if exist.