DOWNLOAD LG AS-H186V_L1_L2 Service Manual ↓ Size: 4.48 MB | Pages: 63 in PDF or view online for FREE

1. Push the front panel backward and lift it up to remove the two screws.

2. As soon as you lift the both lower parts of panel front, you can hear the sound from panel front. At this moment

panel front is separated

3. After pulling down this panel a bit, separate connecting wire from the product.

1. Remove two screws(for fixing cover pipe)
2. Pull up the side cover of desired connecting direction,

then cover side is separated.

3. Pick the pipe hole of the side cover.

When making pipe path through rear
wall, you don’t need to pick the pipe hole.

1. Remove the rubber stopple in the desired drain direc-

tion.

2. Insert drain hose into the handle of drain pan, and

join drain hose and connecting hose according to the
figure by.

Panel Front 

Connector

Pipe hole

Side cover

rubber cap

Only one

desiring direction

Connecting

part

Adhesive

Drain

hose

The wall you select should be strong and solid
enough to prevent vibration

1. Mount the installation plate on the wall with 

type "A" screws. If mounting the unit on a concrete
wall, use anchor bolts.

• Mount the installation plate horizontally by aligning

the centerline using a level.

2. Measure the wall and mark the centerline. It is also

important to use caution concerning the location of
the installation plate-routing of the wiring to power
outlets is through the walls typically. Drilling the
hole through the wall for piping connections must
be done safely.

Installation Plate

Type "A" screw

240mm

60mm

240mm

60mm

Ø 70mm

Ø 70mm

• Drill the piping hole with a ø70mm hole core drill.

Drill the piping hole at either the right or the left with
the hole slightly slanted to the outdoor side.

5-7mm

(3/16"~5/16")

Indoor

WALL

Outdoor

Main cause for gas leakage is due to defect in flaring work. Carry out correct flaring work in the following procedure.

1. Use the piping kit accessory or the pipes purchased

locally.

2. Measure the distance between the indoor and the

outdoor unit.

3. Cut the pipes a little longer than measured distance.

4. Cut the cable 1.5m longer than the pipe length.

1. Completely remove all burrs from the cut cross sec-

tion of pipe/tube.

2. Put the end of the copper tube/pipe in a downward

direction as you remove burrs in order to avoid drop-
ping burrs into the tubing.

• Remove flare nuts attached to indoor and outdoor unit,

then put them on pipe/tube having completed burr
removal.
(not possible to put them on after flaring work)

1. Firmly hold copper pipe in a die in the dimension

shown in the table below.

2. Carry out flaring work with the flaring tool.

Copper

pipe

90

°

Slanted   Uneven  Rough

Pipe

Reamer

Point down

Flare nut

Copper tube

mm

inch

mm

Ø6.35

1/4

0~0.5

Ø9.52

3/8

0~0.5

Ø12.7

1/2

0~0.5

Ø15.88

5/8

0~1.0

Ø19.05

3/4

1.0~1.3

Outside diameter

A

Bar

Copper pipe

Clamp handle

Red arrow mark

Cone

Yoke

Handle

Bar

"A"

1. Compare the flared work with the figure by.

2. If a flared section is defective, cut it off and do flaring

work again.

Preparing the indoor unit's piping and drain hose for installation through the wall.

1. Route the indoor tubing and the drain hose in the

direction of rear left or right

2. Tape the tubing, drain hose and the connecting cable.

Be sure that the drain hose is located at the lowest
side of the bundle. Locating at the upper side can
cause drain pan to overflow inside the unit.

Inclined

Inside is shiny without scratches

Smooth all round

Even length

all round

Surface

damaged

Cracked Uneven

thickness

= Improper flaring =

Drain hose

Connecting
cable

Gas side piping

Liquid side piping

Drain hose

Loop