JBL P9632 User Manual / Operation Manual ▷ View online
Remove the orange wire cover by inserting a small
screwdriver into the notch between the two terminals and
prying upwards. Disconnect the tweeter wires from the
terminal. Reinstall the cover after removing the tweeter.
screwdriver into the notch between the two terminals and
prying upwards. Disconnect the tweeter wires from the
terminal. Reinstall the cover after removing the tweeter.
Detach the tweeter by turning it counterclockwise to
unlock it, then pull it away from the woofer while feeding
the wires through the pole piece.
Install the woofer phase plug and turn it clockwise to lock
it in place.
unlock it, then pull it away from the woofer while feeding
the wires through the pole piece.
Install the woofer phase plug and turn it clockwise to lock
it in place.
05
Figure 5a.
Converting the P-432, P-532 and P-632 to a component system using the optional P-Kit
(sold separately), as shown on pages 5 and 6.
(sold separately), as shown on pages 5 and 6.
Separating the tweeter and woofer, as shown in Figures 5a and 5b.
Figure 5b.
P-Series Owner's Manual 5/25/99 9:46 AM Page 5
06
Figure 6a.
Figure 6b.
Remove the top of the passive crossover by squeezing
the sides and lifting off the top. Mount the crossover
with screws or wire ties through the mounting holes.
Connect the wires between the crossover, and between
the woofer and tweeter as shown.
the sides and lifting off the top. Mount the crossover
with screws or wire ties through the mounting holes.
Connect the wires between the crossover, and between
the woofer and tweeter as shown.
Position the "Lo Pass" and "Twt Frq" according to the
speaker you are using as shown in the callouts in Figure 7b.
speaker you are using as shown in the callouts in Figure 7b.
Jumper Functions
Lo Pass (Low Pass): You may engage or disengage the
woofer low-pass filter with this jumper. Because the
natural rolloff of the P-532 and the P-632 begin at a lower
frequency than that of the P-432, this jumper should only
be in the "on" position when the P-432 is being used.
Lo Pass (Low Pass): You may engage or disengage the
woofer low-pass filter with this jumper. Because the
natural rolloff of the P-532 and the P-632 begin at a lower
frequency than that of the P-432, this jumper should only
be in the "on" position when the P-432 is being used.
Twt Lvl (Tweeter Level): You may attenuate the level of
the tweeter's output using this jumper.
the tweeter's output using this jumper.
Twt Frq (Tweeter Frequency): Because the P-432 has
usable frequency response higher than that of the P-532
or P-632, the optimum crossover frequency for the tweeter
is slightly higher when the P-23t is used with the 4" woofer.
usable frequency response higher than that of the P-532
or P-632, the optimum crossover frequency for the tweeter
is slightly higher when the P-23t is used with the 4" woofer.
Note: For the most accurate sound reproduction,
the jumper positions should be set according to JBL
recommendations. If an alternate setting better suits
your preference or works better for your particular
installation, you may position the jumpers as you like
without affecting your warranty.
the jumper positions should be set according to JBL
recommendations. If an alternate setting better suits
your preference or works better for your particular
installation, you may position the jumpers as you like
without affecting your warranty.
Note: You may upgrade the performance of the P-432,
P-532 or P-632 (when it is used as a multielement speak-
er) by utilizing the passive crossover contained in the
P-Kit and leaving the tweeter mounted on the woofer.
P-532 or P-632 (when it is used as a multielement speak-
er) by utilizing the passive crossover contained in the
P-Kit and leaving the tweeter mounted on the woofer.
Surface-mounting the P-23t.
Flush-mounting the P-23t (use a hole saw to cut a 1-9/16"
hole in the mounting surface).
hole in the mounting surface).
Figure 7a.
Figure 7b.
Mounting the tweeter (P-23t), as shown in Figures 6a
and 6b. The tweeter may be either surface-mounted or
flush-mounted with parts supplied in the P-Kit.
and 6b. The tweeter may be either surface-mounted or
flush-mounted with parts supplied in the P-Kit.
Connecting the woofer and tweeter to the
passive crossover, as shown in Figures 7a and 7b.
passive crossover, as shown in Figures 7a and 7b.
P-Series Owner's Manual 5/25/99 9:46 AM Page 6
07
P-432
P-532
P-632
P-9632
P-9633
4" 2-Way or
5-1/4" 2-Way or
6-1/2" 2-Way or
6" x 9" 2-Way
6" x 9" 3-Way
Component System
Component System
Component System
Component System
Component System
with Optional P-Kit
with Optional P-Kit
with Optional P-Kit
Woofer-Cone Material
Thermalum™
Thermalum™
Thermalum™
Thermalum™
Thermalum™
Tweeter-Diaphragm Material
NeoGlass™
NeoGlass™
NeoGlass™
NeoGlass™
NeoGlass™
Frequency Response
65Hz – 22kHz
55Hz – 22kHz
45Hz – 22kHz
25Hz – 22kHz
25Hz – 22kHz
Sensitivity
90dB
90dB
91dB
92dB
92dB
Recommended Amplifier
Power Range as Multielement
5W – 120W
5W – 150W
5W – 175W
5W – 250W
5W – 250W
Recommended Amplifier Power
Range as Component
5W – 175W
5W – 200W
5W – 225W
N/A
N/A
Mounting Depth
2" (51mm)
2-1/4" (57mm)
2-1/2" (64mm)
3-1/8" (80mm)
3-1/8" (80mm)
Specifications
P-332
P-6432
P-7532
P-23t
P-Kit
3-1/2" 2-Way
4" x 6" 2-Way
5" x 7" 2-Way or
Component
Conversion Kit
Component System
Plate
Component System
Tweeter
for P-432, P-532,
with Optional P-Kit
P-632, P-7532
Woofer-Cone Material
Thermalum™
Thermalum™
Thermalum™
N/A
N/A
Tweeter-Diaphragm Material
NeoGlass™
NeoGlass™
NeoGlass™
NeoGlass™
N/A
Frequency Response
70Hz – 22kHz
65Hz – 22kHz
45Hz – 22kHz
5kHz – 22kHz
N/A
Sensitivity
89dB
90dB
91dB
91dB
N/A
Recommended Amplifier
(with crossover)
Power Range as Multielement
5W – 90W
5W – 150W
5W – 175W
5W – 100W
N/A
Recommended Amplifier Power
Range as Component
N/A
N/A
N/A
N/A
N/A
Mounting Depth
1-3/4" (45mm)
1-7/8" (48mm)
2-1/4" (58mm)
7/8" (23mm)
7/8" (23mm)
P-Series Owner's Manual 5/25/99 9:46 AM Page 7
JBL Consumer Products, 250 Crossways Park Drive, Woodbury, NY 11797
800-336-4JBL (4525) www.jbl.com Part No. POWSPKRSOM Made in China
800-336-4JBL (4525) www.jbl.com Part No. POWSPKRSOM Made in China
Declaration of Conformity
Kongevejen 194B
DK-3460 Birkerød
DENMARK
DK-3460 Birkerød
DENMARK
declare in own responsibility, that the products
described in this owner’s manual are in compliance
with technical standards:
EN 50081-1:1992
EN 50082-1:1992
Steen Michaelsen
Birkerød. DENMARK. 3/99
P-Series Owner's Manual 5/25/99 9:46 AM Page 8
Display