DOWNLOAD JBL P6432 Service Manual ↓ Size: 165.03 KB | Pages: 8 in PDF or view online for FREE

Remove the orange wire cover by inserting a small 
screwdriver into the notch between the two terminals and
prying upwards.  Disconnect the tweeter wires from the
terminal.  Reinstall the cover after removing the tweeter.

Detach the tweeter by turning it counterclockwise to
unlock it, then pull it away from the woofer while feeding
the wires through the pole piece. 
Install the woofer phase plug and turn it clockwise to lock
it in place.

05

Figure 5a.

Converting the P-432, P-532 and P-632 to a component system using the optional P-Kit 
(sold separately), as shown on pages 5 and 6.

Separating the tweeter and woofer, as shown in Figures 5a and 5b.

Figure 5b.

P-Series Owner's Manual  5/25/99  9:46 AM  Page 5

06

Figure 6a. 

Figure 6b.

Remove the top of the passive crossover by squeezing
the sides and lifting off the top. Mount the crossover
with screws or wire ties through the mounting holes.
Connect the wires between the crossover, and between
the woofer and tweeter as shown.

Position the "Lo Pass" and "Twt Frq" according to the
speaker you are using as shown in the callouts in Figure 7b.

Jumper Functions
Lo Pass (Low Pass): You may engage or disengage the
woofer low-pass filter with this jumper. Because  the 
natural rolloff of the P-532 and the P-632 begin at a lower
frequency than that of the P-432, this jumper should only
be in the "on" position when the P-432 is being used.

Twt Lvl (Tweeter Level): You may attenuate the level of
the tweeter's output using this jumper.

Twt Frq (Tweeter Frequency): Because the P-432 has
usable frequency response higher than that of the P-532
or P-632, the optimum crossover frequency for the tweeter
is slightly higher when the P-23t is used with the 4" woofer.

Note: For the most accurate sound reproduction, 
the jumper positions should be set according to JBL 
recommendations. If an alternate setting better suits
your preference or works better for your particular 
installation, you may position the jumpers as you like
without affecting your warranty.

Note: You may upgrade the performance of the P-432, 
P-532 or P-632 (when it is used as a multielement speak-
er) by utilizing the passive crossover contained in the 
P-Kit and leaving the tweeter mounted on the woofer.

Surface-mounting the P-23t.

Flush-mounting the P-23t (use a hole saw to cut a 1-9/16"
hole in the mounting surface).

Figure 7a.

Figure 7b. 

Mounting the tweeter (P-23t), as shown in Figures 6a
and 6b. The tweeter may be either surface-mounted or
flush-mounted with parts supplied in the P-Kit. 

Connecting the woofer and tweeter to the 
passive crossover, as shown in Figures 7a and 7b.

P-Series Owner's Manual  5/25/99  9:46 AM  Page 6

07

4" 2-Way or

5-1/4" 2-Way or

6-1/2" 2-Way or

6" x 9" 2-Way

6" x 9" 3-Way

Component System

Component System

Component System

Component System

Component System

with Optional P-Kit

with Optional P-Kit

with Optional P-Kit

Thermalum™

Thermalum™

Thermalum™

Thermalum™

Thermalum™

NeoGlass™

NeoGlass™

NeoGlass™

NeoGlass™

NeoGlass™

65Hz – 22kHz

55Hz – 22kHz

45Hz – 22kHz

25Hz – 22kHz

25Hz – 22kHz

90dB

90dB

91dB

92dB

92dB

5W – 120W

5W – 150W 

5W – 175W

5W – 250W

5W – 250W 

5W – 175W

5W – 200W

5W – 225W

N/A

N/A

2" (51mm)

2-1/4" (57mm)

2-1/2" (64mm)

3-1/8" (80mm)

3-1/8" (80mm)

3-1/2" 2-Way

4" x 6" 2-Way

5" x 7" 2-Way or

Component

Conversion Kit

Component System

Plate

Component System

Tweeter

for P-432, P-532,

with Optional P-Kit

P-632, P-7532

Thermalum™

Thermalum™

Thermalum™

N/A

N/A

NeoGlass™

NeoGlass™

NeoGlass™

NeoGlass™

N/A

70Hz – 22kHz

65Hz – 22kHz

45Hz – 22kHz

5kHz – 22kHz

N/A

89dB

90dB

91dB

91dB

N/A

(with crossover)

5W – 90W

5W – 150W 

5W – 175W

5W – 100W 

N/A

N/A

N/A

N/A

N/A

N/A

1-3/4" (45mm)

1-7/8" (48mm)

2-1/4" (58mm)

7/8" (23mm)

7/8" (23mm)

P-Series Owner's Manual  5/25/99  9:46 AM  Page 7

JBL Consumer Products, 250 Crossways Park Drive, Woodbury, NY 11797
800-336-4JBL (4525)  www.jbl.com  Part No. POWSPKRSOM Made in China

Declaration of Conformity

Kongevejen 194B 
DK-3460 Birkerød
DENMARK

declare in own responsibility, that the products

described in this owner’s manual are in compliance

with technical standards: 

EN 50081-1:1992

EN 50082-1:1992

Steen Michaelsen

Birkerød. DENMARK. 3/99

P-Series Owner's Manual  5/25/99  9:46 AM  Page 8