JBL MA6002 (serv.man2) Service Manual ▷ View online
MA6002 PACKAGE
4
MARINE
series
MA6002
MA6004 PACKAGE
5
MARINE
series
MA6004
3
INSTALLATION
POWER CONNECTIONS
The amplifier requires a reliable
connection to the boat’s electrical
system in order to perform optimally.
See Figures 1 and 2 for terminal con-
nection locations. Please adhere to
the following instructions carefully:
The amplifier requires a reliable
connection to the boat’s electrical
system in order to perform optimally.
See Figures 1 and 2 for terminal con-
nection locations. Please adhere to
the following instructions carefully:
Ground Connection
Connect the amplifier’s Ground (GND)
terminal to the battery’s negative terminal,
using a ring terminal. Refer to the wire gauge
chart to determine minimum wire gauge size.
Connect the amplifier’s Ground (GND)
terminal to the battery’s negative terminal,
using a ring terminal. Refer to the wire gauge
chart to determine minimum wire gauge size.
Power Connection
Connect a wire (see chart at right for
appropriate gauge) directly to the positive
battery terminal, and install an appropriate
fuse holder within 18" of the battery terminal.
Do not install the fuse at this time. Route
the wire to the amplifier’s location, and
connect it to the amplifier’s Positive (+12V)
terminal. Be sure to use appropriate
grommets whenever routing wires through
a bulkhead or other obstruction. Failure to
adequately protect the positive wire from
potential damage may result in a fire. When
you are done routing and connecting this
wire, you may install the fuse at the battery.
Connect a wire (see chart at right for
appropriate gauge) directly to the positive
battery terminal, and install an appropriate
fuse holder within 18" of the battery terminal.
Do not install the fuse at this time. Route
the wire to the amplifier’s location, and
connect it to the amplifier’s Positive (+12V)
terminal. Be sure to use appropriate
grommets whenever routing wires through
a bulkhead or other obstruction. Failure to
adequately protect the positive wire from
potential damage may result in a fire. When
you are done routing and connecting this
wire, you may install the fuse at the battery.
Remote Connection
Connect the amplifier’s Remote (REM)
terminal to the source unit’s Remote Turn-
On lead using a minimum of 18-gauge wire.
Connect the amplifier’s Remote (REM)
terminal to the source unit’s Remote Turn-
On lead using a minimum of 18-gauge wire.
NOTE: If your source unit does not have
a remote turn-on connection, connect
the amplifier’s (REM) terminal to a wire
that provides +12V when the boat’s acces-
sories are on or when the key is switched
on. If no such circuit exists, install a
switch. See Figure 3.
a remote turn-on connection, connect
the amplifier’s (REM) terminal to a wire
that provides +12V when the boat’s acces-
sories are on or when the key is switched
on. If no such circuit exists, install a
switch. See Figure 3.
Figure 3. Install a switch for the Remote
Turn-On lead.
Turn-On lead.
Speaker Connections
Refer to the application guides on the
pages that follow. Speaker connections
should be made using a minimum of
16-gauge wire.
Refer to the application guides on the
pages that follow. Speaker connections
should be made using a minimum of
16-gauge wire.
Wire Gauge Chart
Amplifier
Amplifier
Maximum
Minimum
Model
Current Draw
Wire Gauge
MA6002
22A #8
AWG
MA6004
40A #8
AWG
These recommendations assume 10' – 12'
wire runs. If your amplifier will be mounted
farther than 12' from the boat’s battery, use
a larger gauge.
wire runs. If your amplifier will be mounted
farther than 12' from the boat’s battery, use
a larger gauge.
Figure 2. Terminal connection end plate for MA6002.
Figure 1. Terminal connection end plate for MA6004.
NC
NO
+12V
AMP REM
6
MARINE
series
MA6002/6004
4
APPLICATIONS – MA6004
The MA6004 can be set up for stereo
4-channel, 3-channel or bridged
2-channel operation, as shown in
Figures 4 through 6.
4-channel, 3-channel or bridged
2-channel operation, as shown in
Figures 4 through 6.
NOTE: For simplicity, Figures 4 through
6 do not show power, remote and input
connections.
6 do not show power, remote and input
connections.
NOTE: Minimum speaker impedance
for stereo operation is 2 ohms.
Minimum speaker impedance for
bridged operation is 4 ohms.
for stereo operation is 2 ohms.
Minimum speaker impedance for
bridged operation is 4 ohms.
Figure 4. MA6004 amplifier in 4-channel (stereo)
operation to drive front and rear full-range speakers.
operation to drive front and rear full-range speakers.
Figure 5. MA6004 is set up for 3-channel operation
to drive a set of full-range speakers and a subwoofer.
to drive a set of full-range speakers and a subwoofer.
Front Right
Front Left
Rear Right
Rear Left
Front Right
Front Left
Figure 6. MA6004 used in bridged 2-channel mode to
drive a set of components or subwoofers. Set crossovers
according to application.
drive a set of components or subwoofers. Set crossovers
according to application.
Rear Right
Rear Left
Front Right
Front Left
Front Right
Front Left
7
Click on the first or last page to see other MA6002 (serv.man2) service manuals if exist.